BDI CENTRO, 6401 Assembly Instructions Manual

CENTROTM 6401

DESK

Product Registration

Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today and you will be entered to win free a BINK
table from BDI. www.bdiusa.com/product-registration/

[e-mail]

bdiusa.com

T1 4mm Hex Wrench

Placement and Maintenance

Centro™ Office furniture is designed for indoor use on level floors. Clean
glass with glass cleaner, and steel parts and wood veneer with a moist
cloth.

Your Centro™ Office furniture is engineered for easy assembly. Carefully
follow this procedure to prevent any damage.
Do not use power tools for assembly of this product.

Step 1

Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, please contact BDI Customer Service at customerservice@
bdiusa.com. For all other concerns, please contact your BDI retailer.

C1 Glass Panel x 1

H1 1/4-20 x 15 mm Screw x 16

H8 1/4-20 x 61 mm Screw x 5

H9 Leveler Glide x 4

H10 Bumper x 4

C5 Drawer Liner x 1

C2 Back Panel x 1

C8 Left Leg x 1

Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Centro & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2015, BDI
Made in Taiwan. 12.2.2015 V2

C6 Upper Trough x 1

C9 Right Leg x 1

C4 Desk Frame x 1

C3 Front Panel x 1

C7 Lower Trough x 1

Step 1 - Install Leveler Glides H9 to the bottom of Left Leg C8 and Right Leg C9.

H9 (x4)

C9

2

CENTRO 6401
DESK

C8

bdiusa.com

[e-mail]

Step 2 - Attach Left Leg C8 to Desk Frame using Screw H1 and Hex Wrench.

H1 (x4)

Step 3 - Attach Right Leg C9 to Desk Frame using Screw H1 and Hex Wrench.

H1 (x4)

3

CENTRO 6401
DESK

bdiusa.com

[e-mail]

Step 4 - Adhere Bumper H10 to top surface of Upper Trough C6.

H10 (x4)

Step 5 - Attach Upper Trough C6 to inside of Left and Right Leg using Screw H1 and Hex Wrench.

H1 (x4)

4

CENTRO 6401
DESK

bdiusa.com

[e-mail]

Step 6 - Attach Lower Trough C7 to inside of Left and Right Leg using Screw H1 and Hex Wrench.

H1 (x4)

5

CENTRO 6401
DESK

bdiusa.com

[e-mail]

Step 7 - With the help of another person, gently lower assembly onto Glass Panel. Both parts are upside down
for the assembly process.

Step 8 - Fasten into place using Screw H8 and Hex Wrench. DO NOT OVERTIGHTEN! Upon completion, turn
desk upright onto its base.

H8 (x5)

6

CENTRO 6401
DESK

bdiusa.com

[e-mail]

Step 9 (optional) - Attach Magnets to AC power strip/surge protector (not included)
Remove Magnets from the Upper Trough C6. Peel film from side of the Magnets and attach to clean, dry
back side of AC power strip (not included). Cleaning of power strip surface with rubbing alcohol will

ensure best adhesive bond. **UNPLUG POWER STRIP FROM POWER SOURCE BEFORE CLEANING**

7

CENTRO 6401
DESK

bdiusa.com

[e-mail]

Step 10 - Install Front Panel C3 as shown. The rear side of panel has pre-installed magnets that hold panel
into position. Note: The Centro Desk is designed to permit placement in front of an electrical outlet for easier
wiring access.

Optional
The Back Panel C2 is provided to conceal wire management if desk is located in the middle of a room.

8

CENTRO 6401
DESK

bdiusa.com

[e-mail]