BDI 6234 User Manual

ASPECT

ASSEMBLY INSTRUCTIONS

Component List

6234

A - Phillips Screwdriver
x 1

B - M4 x 20mm Screw
x 4

C - 10-32 x 1/2" Screw
x 8

D - Attachment Plate
x 2

E - Short Pull
x 2

F - Hutch
x 1

BDIUSA.COM [e-mail]

Aspect is engineered for easy assembly and is designed for use
only with Aspect Desk 6231, sold separately. Carefully follow this
procedure to prevent any damage.

Do not use power tools for assembly of this product.

Placement and Maintenance

Aspect is designed for indoor use on level floors. Clean steel parts
and wood veneer with a moist cloth.

Step 1
Unpack and Identify

Unpack and identify the components at left. Note that some
components are shipped inside the hutch. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at [e-mail]. For all other concerns, please
contact your BDI Retailer.

Step 2

With the help of another person, position the Aspect Desk at least
12"/ 31 cm from the wall of the desired location.

2 Person Task

G - Removable Shelf
x 1

H - Large Adjustable Shelf
x 1

12" /

31 cm

Designed by Matthew Weatherly.

These distinctive product congurations are protected by US and

international patents, trade dress, and/or copyright laws.
BDI and Aspect are trademarks of Becker Designed, Inc.
All Rights reserved. ©2014, BDI
Made in China. 6234REV112114v2

1

Step 3
With the help of another person, carefully lower Hutch (F) onto the Aspect
Desk.

F

2 Person Task

Step 4
Fasten back of Hutch (F) with Attachment Plate (D) using Screw (C) and

Phillips Screwdriver (A).

C x 8

D x 2

Step 5

With the help of another person, position the Desk/Hutch assembly in its
desired location.

ASPE CT

62 34

2

2 Person Task

assembly instructio ns

bdiusa.com [e-mail]

Step 6
Install Short Pull (E) onto the Hutch doors using Screw (B) and install
Shelves (G and H) into the Hutch.

G

E x 2

B x 4

H

ASPE CT

62 34

3

assembly instructio ns

bdiusa.com [e-mail]

Fine tuning your new BDI Aspect Hutch

These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your Aspect Hutch. Due to jostling in freight or perhaps an uneven floor, the doors on your Aspect Hutch may
not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware
that depending on your situation, patience and a bit of trial and error are required. The high-quality European
hinge hardware is infinitely adjustable, but changing one element can cause the need for further adjustments.
Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are
sitting perfectly on your Aspect unit.

INCORRECT! Door is
out of alignment with
the rest of the unit.

CORRECT! Door is
sitting squarely and
evenly spaced on tops
and sides.

STEP 2 - Adjust Door Hinges (if needed)

The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame.

If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment to the
European hinges on each door.

Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the need for

adjustments to other elements. But with a few adjustments, you
can modify the orientation of the cabinet doors to make sure
that they hang perfectly within your cabinet.

Use the Phillips Screwdriver (A) supplied to adjust Aspect's
door hinges:

• By adjusting Screw 1, the door will move LEFT or

RIGHT within the frame. Make minor adjustments
at both top and bottom hinges for best results.

2.

1.

• By adjusting Screw 2 the entire door will move IN or

OUT, opening or closing the gap between the door
frame and cabinet. (This screw rarely needs adjustment.)

2.

1.

ASPE CT

62 34

4

assembly instructio ns

bdiusa.com [e-mail]