BDI 6112 Instruction Manual

SEQUEL® 20 6112
RETURN
INSTRUCTION MANUAL
LET’S GET STARTED.
DESIGN MATTHEW WEATHERLY
has been designed to provide a lifetime of enjoyment. This manual will provide you with
assembly instructions and other helpful information that will ensure that you get the
most out of your return. Please save it for future reference.
Your Sequel 20 Return has been engineered for simple assembly. Please follow these
directions carefully to prevent any damage.
Should you need further assistance, contact BDI at customerservice@bdiusa.com.
ENJOY!
BDIUSA.COM | 3NEED ASSISTANCE? customerservice@bdiusa.com
HARDWARE AND COMPONENTSHARDWARE AND COMPONENTS
Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com.
Do not use power tools for assembly of this product.
For all other concerns, please contact your BDI retailer.
PART # T1
DESCRIPTION Hex Wrench
QUANTITY 1
PART # H2
DESCRIPTION
QUANTITY 4
M6 x 10mm Flathead
Screw
PART # T2
DESCRIPTION Hex Wrench
QUANTITY 1
PART # H3
DESCRIPTION M6 x 15mm Screw
QUANTITY 5
PART # H1
DESCRIPTION M6 x 40mm Screw
QUANTITY 4
PART # H4
DESCRIPTION Leveler
QUANTITY 2
4 | BDIUSA.COM SEQUEL 20 6112
HARDWARE AND COMPONENTS
PART # C1
DESCRIPTION Leg Frame
QUANTITY 1
PART # C3
DESCRIPTION Connector Plate
QUANTITY 1
PART # C2
DESCRIPTION Top Frame
QUANTITY 1
PART # C4
DESCRIPTION Top Panel
QUANTITY 1
BDIUSA.COM | 5NEED ASSISTANCE? customerservice@bdiusa.com
ASSEMBLY
STEP 1. INSTALL LEVELERS
Install (H4) Levelers into the bottom of (C1) Leg Frame.
PART/DESCRIPTION QTY
H4-LEVELER 2
H4
H4
H4
ASSEMBLY
STEP 2. INSTALL TOP FRAME
Connect (C1) Leg Frame to (C2) Top Frame using 4 (H1) Screws and tighten with (T1) Hex Wrench.
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
C1
C1
H1
H1
H1-SCREW 4
C2
6 | BDIUSA.COM SEQUEL 20 6112
STEP 3. INSTALL CONNECTOR PLATE
ASSEMBLY
The return may be attached to either a desk or a cabinet.
IF ATTACHING TO A DESK— COMPATIBLE WITH 6101, 6102:
PART/DESCRIPTION QTY
Connect the (C3) Connector Plate to the underside of (C2) Top Frame using 2 (H2)
T1-HEX WRENCH 1
Flathead Screws and (T1) Hex Wrench. Make sure notch is facing outward. Go to step 4.
H2-FLATHEAD SCREW 2
IF ATTACHING TO A CABINET— COMPATIBLE WITH 6114, 6116, 6117:
Connect the (C3) Connector Plate to the topside of (C2) Top Frame using 2 (H2) Flathead Screws. Make sure notch is facing outward. Go to step 8.
Connecting to desk
plate goes on bottom
Connecting to cabinet
plate goes on the top
notch
H2
notch
H2
C2
C3
H2
H2
C3
C2
BDIUSA.COM | 7NEED ASSISTANCE? customerservice@bdiusa.com
STEP 4. INSTALL SCREW FOR CONNECTOR PLATEASSEMBLY
The return may be attached either to the left or right of the center drawer (right side shown below). Partially thread 1 (H3) Screw into the middle insert leaving it extended out 1/4"
(6mm) to allow (C3) Connector Plate to slide into the space between the screw head and bottom of the desk.
PART/DESCRIPTION QTY
H3-SCREW 1
1/4" (6mm) gap
H3
H3
8 | BDIUSA.COM SEQUEL 20 6112
STEP 5. ATTACH THE RETURN
ASSEMBLY
Slide the notch on (C3) Connector Plate onto the partially threaded middle screw. Tighten the screw with (T1) Hex Wrench.
C3
Insert (H2) Flathead Screws into the left and right holes on the (C3) Connector Plate and tighten with (T1) Hex Wrench.
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
H2
H2-FLATHEAD SCREW 2
C3
H2
BDIUSA.COM | 9NEED ASSISTANCE? customerservice@bdiusa.com
STEP 6. INSTALL TOP PANELASSEMBLY
Attach (C4) Top Panel by placing it on top of the return and fastening with (H3) Screws going through the metal tabs in the corners and into the inserts on the underside of the (C4) Top Panel. Make sure the gap between desk glass and return glass is even, then tighten with
(T1) Hex Wrench.
C4
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
H3-SCREW 4
H3
H3
H3
H3
10 | BDIUSA.COM SEQUEL 20 6112
STEP 7. INSTALL TOP PANEL
ASSEMBLY
The return may be attached to the left or right side of the following cabinets:
n
6114 3 Drawer File Pedestal
n
6116 Lateral File
n
6117 Multi-Function Cabinet—shown below
First, remove the glass top from the cabinet. Attach the (C3) Connector Plate to the cabinet using (H2) Flathead Screws going through the (C3) Connector Plate and into the 2 threaded holes on the top of the cabinet. Tighten with (T1) Hex Wrench. Re-install the glass top onto the cabinet.
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
H2-FLATHEAD SCREW 2
H2
H2
H2
BDIUSA.COM | 11NEED ASSISTANCE? customerservice@bdiusa.com
STEP 8. ATTACH TOP PANELASSEMBLY
Attach (C4) Top Panel by placing it on top of the return and fastening with (H3) Screws going through the metal tabs in the corners and into the inserts on the underside of the (C4) Top Panel. Make sure the gap between desk glass and return glass is even, then tighten with
(T1) Hex Wrench.
C4
H3
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
H3-SCREW 4
H3
H3
H3
12 | BDIUSA.COM SEQUEL 20 6112
CARE & MAINTENANCE
GLASS
Glass surface is maintained using household glass cleaner and a paper towel or cloth.
SATIN-ETCHED GLASS
This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available at any grocery store or home improvement center. Dampen the entire glass surface as well as the Magic Eraser, then rub the entire glass surface in broad, even strokes using moderate pressure. Clean and dry the surface with a paper towel. Check for results and repeat as necessary.
Any scratches or scuffing not eliminated by one of the above methods can often be addressed by ‘refreshing’ the glass. This is a process that should not be required more than once per 6-12 months. See this brief video for the simple method: www.bdiusa.com/glass
WOOD
Wood surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. Do not use glass cleaner on wood. If moisture remains, dry the surface with another cloth. If needed, a gentle non-abrasive cleanser may be used, but be sure to wipe away all cleaner residue and dry the surface with a cloth.
BDI’s wood finishes feature natural hardwood solids and veneers. Wood is a product of nature and— unlike man-made materials that can be manufactured to strict and consistent specifications—has natural imperfections that are part of its appeal and character. Every piece of wood differs from every other, even when coming from the very same tree. As such, variation in grain, texture and tone should be expected from one panel or piece of furniture to the next.
While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid positioning your BDI cabinet in any area with extensive direct sunlight. To learn more about the features of natural wood, visit www.bdiusa.com/wood
METAL & PAINTED SURFACES
Surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. If moisture remains, dry the surface with another cloth. If needed, a gentle non-abrasive cleanser may be used, but be sure to wipe away all cleaner residue and dry the surface with a cloth.
BDIUSA.COM | 13NEED ASSISTANCE? customerservice@bdiusa.com
WARRANTY
BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. The decision to repair or replace will be at BDI’s sole discretion.
BDI Home Theater Furniture, Office Furniture, Modular Systems, Tables and other furniture pieces are warranted for three (3) years from the date of purchase as shown on your sales receipt. The warranty period starts from the date of purchase. This warranty extends only to the original purchasers who acquire new product from BDI Authorized Resellers. Any product, part, or component must have been assembled, installed, used, and maintained according to BDI’s published instructions in order to be eligible for warranty coverage. Any modification to the original product voids the warranty.
To view BDI’s complete warranty information, visit www.bdiusa.com/warranty
PRODUCT REGISTRATION
Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.com/register
WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM FURNITURE TIP-OVER. TO HELP PREVENT TIP-OVER:
nInstall tip-over restraint. n Place heaviest items in lower compartments. nNever allow children to climb or hang on drawers, doors or shelves. nNever open more than one drawer at a time.
USE OF TIP-OVER RESTRAINT MAY REDUCE—BUT NOT ELIMINATE—THE RISK OF TIP-OVER.
14 | BDIUSA.COM SEQUEL 20 6112
BDIUSA.COM | 15NEED ASSISTANCE? customerservice@bdiusa.com
These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.03.26.2020
Made in Vietnam.
Loading...