BDI 6102 User Manual

SEQUEL® 20 6102

CONSOLE

INSTRUCTION MANUAL

LET’S GET STARTED.

DESIGN MATTHEW WEATHERLY

Congratulations on the purchase of your Sequel 20 Console 6102 from BDI. Your console

has been designed to provide a lifetime of enjoyment. This manual will provide you with

assembly instructions and other helpful information that will ensure that you get the

most out of your console. Please save it for future reference.

Your Sequel 20 Console has been engineered for simple assembly. Please follow these

directions carefully to prevent any damage.

Should you need further assistance, contact BDI at [e-mail].

ENJOY!

BDIUSA.COM | 3NEED ASSISTANCE? [e-mail]

HARDWARE AND COMPONENTSHARDWARE AND COMPONENTS

Unpack and identify the parts listed below. The assembly workspace should be a non-marring
surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at
[e-mail].

Do not use power tools for assembly of this product.

For all other concerns, please contact your BDI retailer.

PART # T1

DESCRIPTION Hex Wrench

QUANTITY 1

PART # C1

DESCRIPTION Left Leg Frame

QUANTITY 1

PART # T2

DESCRIPTION Hex Wrench

QUANTITY 1

PART # H1

DESCRIPTION

QUANTITY 20

PART # C2

DESCRIPTION Right Leg Frame

QUANTITY 1

M6 x 15mm

Screw

PART # H2

DESCRIPTION Leveler

QUANTITY 4

PART # C3

DESCRIPTION Top Frame

QUANTITY 1

4 | BDIUSA.COM SEQUEL 20 6102

PART # C4

DESCRIPTION Lower Horizontal Frame

QUANTITY 1

HARDWARE AND COMPONENTS

PART # C5

DESCRIPTION Upper Horizontal Frame

QUANTITY 1

PART # C8

DESCRIPTION Top Panel

QUANTITY 1

PART # C7

DESCRIPTION 6108 Back Panel—SOLD SEPARATELY

QUANTITY 1

PART # C9

DESCRIPTION Front Panel

QUANTITY 1

BDIUSA.COM | 5NEED ASSISTANCE? [e-mail]

ASSEMBLY

STEP 1. INSTALL LEVELERS

Install (H2) Levelers into the bottom of
(C1) Left and (C2) Right Leg Frames.

PART/DESCRIPTION QTY

H2-LEVELER 4

C1

H2

H2

H2

H2

C2

ASSEMBLY

STEP 2. INSTALL SCREWS (PARTIALLY)

With levelers down, partially install (H1) Screws
into the upper holes of the paired inserts on the
inside edges of (C1) Left and (C2) Right Leg
Frames. (H1) Screw heads should be 1/4" (6mm)
away from frame.

H1H1

H1H1

C1 C2

H1H1

PART/DESCRIPTION QTY

H1-SCREW 8

H1H1

Screw Heads

1/4" (6mm) away from frame

6 | BDIUSA.COM SEQUEL 20 6102

STEP 3. INSTALL TOP FRAME

ASSEMBLY

On a soft surface such as a carpet, position (C2) Right Leg Frame as shown and hook (C3) Top
Frame onto the partially threaded screws on the top of (C2) Right Leg Frame. Slide the frame

down so that the screws go into the keyhole slot.

Wood facia

facing thinner

section of

C3

front leg

C2

C3

C2

Hook onto partially

threaded screw head

Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex Wrench.

PART/DESCRIPTION QTY

T1-HEX WRENCH 1

H1-SCREW 2

H1 H1

BDIUSA.COM | 7NEED ASSISTANCE? [e-mail]

STEP 4. INSTALL TOP FRAMEASSEMBLY

Lift and hook the (C3) Top Frame onto the 2
partially threaded screws at the top of (C1) Left
Leg Frame. Insert (H1) Screws into the lower
holes and partially tighten with (T1) Hex

Wrench.

C3

PART/DESCRIPTION QTY

T1-HEX WRENCH 1

H1-SCREW 2

C1

C3

C1

H1

8 | BDIUSA.COM SEQUEL 20 6102

STEP 5. INSTALL LOWER HORIZONTAL FRAME

ASSEMBLY

Lift and hook the (C4) Lower Horizontal Frame
onto the partially threaded screws as shown.
Insert (H1) Screws into the lower holes and

partially tighten with (T1) Hex Wrench.

C2

C1

C4

PART/DESCRIPTION QTY

T1-HEX WRENCH 1

H1-SCREW 2

C1/C2

C4

C1/C2

C4

H1

BDIUSA.COM | 9NEED ASSISTANCE? [e-mail]

STEP 6. INSTALL UPPER HORIZONTAL FRAMEASSEMBLY

Lift and hook the (C5) Upper Horizontal Frame
onto the partially threaded screws as shown.
Insert (H1) Screws into the lower holes and fully
tighten with (T1) Hex Wrench.

Including previous steps, fully tighten all screws!

C5

C1/C2

C5

C2

PART/DESCRIPTION QTY

T1-HEX WRENCH 1

H1-SCREW 2

C1

C5

H1

C1

C5

C2

H1

10 | BDIUSA.COM SEQUEL 20 6102

STEP 7. INSTALL TOP PANEL

ASSEMBLY

Install the (C8) Top Panel as shown and secure
with (H1) Screws going though the metal tabs on
the frame and into the inserts in the corners of
the guide blocks under the (C8) Top Panel.
Tighten using the (T1) Hex Wrench.

H1

H1

C8

H1

PART/DESCRIPTION QTY

T1-HEX WRENCH 1

H1-SCREW 4

H1

BDIUSA.COM | 11NEED ASSISTANCE? [e-mail]

ASSEMBLY

STEP 8. INSTALL BACK PANEL—OPTIONAL

If you plan on placing the console against a wall, do not install the (C7) 6108 Back Panel—sold
separately, otherwise access to a wall outlet may be blocked. If positioning your desk away from a
wall, the (C7) Back Panel may be installed by placing the lower edge into the groove on the (C4)
Lower Horizontal Frame. The top is held in place with magnets.

2

ASSEMBLY

1

STEP 9. INSTALL FRONT PANEL

C7

C4

Install the (C9) Front Panel by placing the bottom edge into the channel on the front of the
(C4) Lower Horizontal Frame. Rotate back and vertically until the top edge magnetically attaches

to the frame.

2

C9

1

C4

12 | BDIUSA.COM SEQUEL 20 6102

LEVEL DESK

If needed, dial out 1 or more of the levelers using (T2) Leveler Wrench.

FINE TUNING

T2

WIRE MANAGEMENT

Wires and cords may be routed as shown through the space.

FINE TUNING

BDIUSA.COM | 13NEED ASSISTANCE? [e-mail]

CARE & MAINTENANCE

GLASS

Glass surface is maintained using household glass cleaner and a paper towel or cloth.

SATIN-ETCHED GLASS

This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass
cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth
can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available
at any grocery store or home improvement center. Dampen the entire glass surface as well as the
Magic Eraser, then rub the entire glass surface in broad, even strokes using moderate pressure. Clean
and dry the surface with a paper towel. Check for results and repeat as necessary.

Any scratches or scuffing not eliminated by one of the above methods can often be addressed by
‘refreshing’ the glass. This is a process that should not be required more than once per 6-12 months.
See this brief video for the simple method: www.bdiusa.com/glass

WOOD

Wood surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. Do not
use glass cleaner on wood. If moisture remains, dry the surface with another cloth. If needed, a gentle
non-abrasive cleanser may be used, but be sure to wipe away all cleaner residue and dry the surface
with a cloth.

BDI’s wood finishes feature natural hardwood solids and veneers. Wood is a product of nature and—
unlike man-made materials that can be manufactured to strict and consistent specifications—has
natural imperfections that are part of its appeal and character. Every piece of wood differs from every
other, even when coming from the very same tree. As such, variation in grain, texture and tone should
be expected from one panel or piece of furniture to the next.

While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some
degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid
positioning your BDI cabinet in any area with extensive direct sunlight. To learn more about the
features of natural wood, visit www.bdiusa.com/wood

METAL & PAINTED SURFACES

Surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. If moisture
remains, dry the surface with another cloth. If needed, a gentle non-abrasive cleanser may be used,
but be sure to wipe away all cleaner residue and dry the surface with a cloth.

14 | BDIUSA.COM SEQUEL 20 6102

WARRANTY

BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or
replace any product, part, or component covered by this warranty which fails under normal use as a
result of a defect in material or workmanship. BDI will repair or replace the aforementioned product,
part or component with a comparable product, part or component. The decision to repair or replace
will be at BDI’s sole discretion.

BDI Home Theater Furniture, Office Furniture, Modular Systems, Tables and other furniture pieces are
warranted for three (3) years from the date of purchase as shown on your sales receipt. The
warranty period starts from the date of purchase. This warranty extends only to the original
purchasers who acquire new product from BDI Authorized Resellers. Any product, part, or
component must have been assembled, installed, used, and maintained according to BDI’s published
instructions in order to be eligible for warranty coverage. Any modification to the original product
voids the warranty.

To view BDI’s complete warranty information, visit www.bdiusa.com/warranty

PRODUCT REGISTRATION

Registering your new BDI product allows us to send you important product updates, service
information and helpful hints related to your BDI products. Register today, and you will be entered
to win free a BINK table from BDI: www.bdiusa.com/register

WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM FURNITURE TIP-OVER. TO HELP
PREVENT TIP-OVER:

nInstall tip-over restraint.
n Place heaviest items in lower compartments.
nNever allow children to climb or hang on drawers, doors or shelves.
nNever open more than one drawer at a time.

USE OF TIP-OVER RESTRAINT MAY REDUCE—BUT NOT ELIMINATE—THE RISK OF TIP-OVER.

BDIUSA.COM | 15NEED ASSISTANCE? [e-mail]

These distinctive product configurations are protected by US and international patents, trade
dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights
reserved. ©2020, BDI | V.03.26.2020

Made in Vietnam.