BDI 6006 User Manual
Se q u e l
600
1
600
2
6
6006
6007
6006 CPU C a b i n e t
a s s e m b l y i n s t r U C t i o n s
b d i U s a .C o m C U s t o m e r s e r v i C e @b d i U s a .C o m
Component List
A - CPU Cabine t x 1
B - 5/32” x 12mm
Phillips Screw x 16
C - Brake Caster x 2
D - Rear Caster x 2
Your Sequel Home Office Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Sequel Home Office Furniture is designed for indoor use on level floors.
Clean steel parts and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some components
are shipped inside the cabinet. The assembly workspace should be a nonmarring surface such as carpet. A Phillips Screwdriver will be needed for
assembly. For missing hardware pieces, please contact BDI Customer
Service at customerservice@bdiusa.com. For all other concerns, please
contact your BDI Retailer.
Step 2
Install Casters
Carefully position CPU Cabinet (A) on its top surface so that bottom
surface is up, then attach a Brake Caster (C) and Rear Caster (D) at
each of the four (4) exposed installation plates using 5/32” x 12mm
Phillips Screw (B) and a Phillips Screwdriver.
E - Back Panel x 1
FRONT
C x 2
B x 8
D x 2
Designed by Matthew Weatherly.
‘Sequel’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2009 Becker Designed, Inc.
Made in Taiwan. 6006REV121509v2
B x 8
1
1.
2.
3.
3.
1.
2.
*
2.
*
Step 3
Install Back Panel
Install Back Panel (E) to the backside of the cabinet by
first inserting the panel into the cabinet then raising it up
and down in to the grooves.
Adjust Door Hinges (if needed)
If the cabinet’s door appears out of alignment, this can be corrected with minor adjustment to the European
hinges on each door.
Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the need for
adjustments to other elements. But with a few adjustments, you can modify the orientation of the cabinet door
to make sure that it hangs evenly.
Use a Phillips screwdriver to adjust Sequel’s door
hinges:
• Screw 1, the door will move
By adjusting
LEFT or RIGHT within the frame. Make minor
adjustments at both top and bottom hinges for
best results.
• Screw(s) 2, the door will move
By adjusting
UP or DOWN within the frame (the top and
bottom hinges must be adjusted the same
degree).
NOTE: Loosen Screws 2 one complete turn,
raise or lower door, then hold in position
while tightening Screws 2 (on both hinges).
• Screw 3 the entire door will
By adjusting
move IN or OUT, opening or closing the gap
between the door frame and cabinet. (This
screw rarely needs adjustment.)
Reverse Door-Swing (if desired)
Sequel features a reversible door assembly so that
you can open either from the left or the right.
To reverse the door’s orientation,
Remove the Door by actuating both of 1.
its quick-release hinges; carefully place the
detached Door aside.
Using a Philips head screwdriver, remove 2.
both Hinge Plates from the interior wall of the
cabinet by loosening the screws holding it in
place.
Install both Hinge Plates to the opposite 3.
interior wall at the pre-determined locations.
Re-install the Door by connecting each Door 4.
Hinge to the relocated Hinge Plates.
2
a s s e m b l y i n s t r U C t i o n s
b d i U s a .C o m C U s to m e r se r v i Ce @bd i U s a .C o m
Loading...