C a s a t a
2823, 8627 a n d 8629-2
a s s e m b l y i n s t r u c t i o n s
2823
8627
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
8629-2
Component List
A - Assembled Cabinet
x 1
B - Flat Wrench x 1
C - Phillips Screwdriver
x 1
D - Adjustable Shelf
Model 8627 x 3
Model 8629-2 x 2
Model 2823 x 3
E - Back Panel x 2
Your Casata Home Theater Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
NOTE: This instruction sheet is intended for the entire Casata collection;
model 8629-2 is shown for illustration.
Placement and Maintenance
Casata Home Theater Furniture is designed for indoor use on level floors.
Clean glass with glass cleaner, and steel parts and wood veneer with a
moist cloth.
Step 1
Unpack and identify the parts listed. The assembly workspace should be a
non-marring surface such as carpet. For missing hardware pieces please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
Step 2
Leveling and Shelf Adjustment
The shelf pins located inside the left and right cabinet space may be
repositioned, allowing you to raise or lower each shelf to the desired level
using the Phillips Screwdriver (C).
F - Allen Wrench x 1
Leveler glides are accessible
near the bottom of the side
panels using the Flat Wrench
(B).
Shelf Pin
Designed by Cristian Wicha.
‘Casata’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2009 Becker Designed, Inc.
Made in China. 8822782292823REV101509v8
For more information about the adjustable levelers and
troubleshooting, be sure to check out “Fine tuning your
new BDI Casata Home Theater Furniture” at the end of
these instructions.
1
Step 3
Back Panel Installation
Install Back Panel (E) to the rear side of cabinet.
Velcro straps are included as wire management for your convenience.
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Fine-tuning your Casata Home Theater Cabinet
1.
2.
3.
3.
1.
2.
*
2.
*
Due to jostling in freight or perhaps an uneven floor, the doors and drawer (if equipped) on your Casata stand may not
appear to be in perfect alignment when first set up. Making a few minor adjustments can rectify this situation. Be aware
that depending on your situation, patience and a bit of trial and error may be required. The high-quality European hinges
are highly adjustable, and changing one element can cause the need for further adjustments. Through a few simple
adjustments, you can modify the orientation of the cabinet doors to ensure that they are hanging evenly.
STEP 1 - Level your cabinet (if needed)
After unpacking and assembling your Casata cabinet, inspect it visually to ensure that it is resting level on the floor, that
all doors appear level and open/close freely without rubbing or binding. Proper adjustment of the cabinet’s levelers quickly
corrects most leveling/alignment issues.
Models 8627 & 8629-2 only: There are five (5) adjustable levelers on the bottom of these cabinets; each may be
individually adjusted depending on your leveling scenario. Turning the leveler clockwise will extend the leveler; turning
it counter-clockwise will retract it. Four (4) of the levelers are accessible near the bottom of the side panels and are
adjustable using the provided Flat Wrench (B). One (1) leveler is accessible from inside the cabinet---in the center of the
bottom panel (Model 8627), or at the rear of the bottom panel (Model 8629-2)---and is adjustable using the provided
Allen Wrench (F).
Model 2823 only: There are six (6) adjustable levelers on the bottom of this cabinet; each may be individually adjusted
depending on your leveling scenario. Turning the leveler clockwise with the provided Flat Wrench (B) will extend the
leveler; turning it counter-clockwise will retract it. Four (4) of the levelers are accessible near the bottom of the side
panels, near front and back. An additional leveler is found on each center leg.
INCORRECT! Door
is out of alignment.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and should open and close freely without rubbing against the door
frame.
If the cabinet’s doors appear out of alignment, this condition can be
corrected with minor adjustments to the European hinges on each
door.
Because these hinges are infinitely adjustable, adjusting one
hinge element can sometimes cause the need for adjustments
to other elements. But with a few adjustments, you can modify
the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use Phillips Screwdriver (C) to adjust the door hinges:
By adjusting
• Screw 1, the door will move LEFT or RIGHT
within the frame. Make minor adjustments at both top and
bottom hinges for best results.
By adjusting • Screw(s) 2, the door will move UP or DOWN
within the frame (the top and bottom hinges must be adjusted
the same degree).
By adjusting • Screw 3 the entire door will move IN or OUT,
opening or closing the gap between the door frame and cabinet
(This screw rarely needs adjustment).
CORRECT! Door is
sitting squarely and
is evenly spaced at
top and sides.
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...