BDI 1542 User Manual

crease

1542 1546
1548 1549

a s s e m b l y i n s t r u c t i o n s

bdiusa.com cust [e-mail]

Component List

A - 4mm Hex Wrench

x 1

B - 1/4-20 x 12mm Screw
1542 x 8
1546 x 8
1548 x 10
1549 x 8

C - Leg x 2

D - Glass Top x 1

E - Wood Shelf x 1

F - Removable

Glass Spacer x 4
(REMOVE SPACER
AFTER ASSEMBLY)

Fig. 1

Crease is engineered for easy assembly.
Carefully follow this procedure to prevent any
damage.

NOTE: This instruction sheet is intended for
the entire Crease table collection; model 1542
is shown for illustration.

Placement and Maintenance

Crease is designed for indoor use on level floors.
Clean glass with glass cleaner, wood and steel
parts with a moist cloth. Many wood surfaces

are subject to fading under direct sunlight. BDI’s

TWO PERSON ASSEMBLY

unique Graphite finish has properties that make it more sensitive
than others. Please avoid placing BDI’s Graphite finish in direct
sunlight.

Step 1
Unpack and Identify

Unpack and identify the components at left. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at [e-mail]. For all other concerns, please
contact your BDI Retailer.

Step 2
Attach Legs to Glass Top

Slide the Removable Glass Spacer (F) over each top end of
the Leg (C) as illustrated in Fig.1. Place Glass Top (D) upside
down on soft surface in order to prevent damage. Hand tighten

Legs (C) to Glass Top (D) using Screws (B). Ensure that the
Removable Glass Spacers (F) are pressed up against the edge
of the Glass Top (D) and tighten Screws (B) using Hex Wrench
(A).

F

F

C

Designed by Dan Fritz .

These distinctive product congurations are protected by US and

international patents, trade dress, and/or copyright laws.
BDI is trademark of Becker Designed, Inc.
All rights reserved. ©2013, BDI
Made in China. 1542154615481549REV10242013v1

C

B

D

Removable
Glass Spacer

1

Step 3
Attach Wood Shelf

With a second person holding the Wood Shelf (E) in place, loosely start all Screws (B).

E

B

Crease 1548 Console Table Only

B

E

B

Step 4
Align Wood Shelf & Turn Table Over

Align the corners of the Wood Shelf (E) with the Leg (C). Once aligned, tighten Screws
(B) using Hex Wrench (A). With the help of a second person, turn table over right side
up, lifting by the table’s Legs (C), .

Correct

Aligned

Incorrect

Not Aligned

E

C

C

E

Step 5
Remove Glass Spacers

Before removing the Glass Spacers (F), make sure there is consistent spacing
between the Legs (C) and the Glass Top (D) as illustrated in Fig. 1A. If necessary,
slightly loosen the misaligned end and adjust the Leg (C) so the Removable Glass

Spacers (F) are pressing against the edge of the Glass Top (D) and re-tighten
screws. Once the table is properly aligned, remove the 4 Glass Spacers (F) by sliding
them upward off the Legs (C) as illustrated in Fig. 2.

Fig. 1A Fig. 1B

Aligned

Not
Aligned

Fig. 2

D

C

cre ase

15 42 1546 1 548 1549

D

C

2

assembly instruction s

bdiusa.com [e-mail]