Bdcom switch module Installation Manual

BDCOM Switch Module Hardware

Installation Guide

Content

Table of Content

Chapter 1 Overview of BDCOM Module...............................................................................................................................1

1.1 Module Overview...................................................................................................................................................1

1.2 Preparing to install the interface card....................................................................................................................1

1.2.1 Safety information.....................................................................................................................................1

1.2.2 Tools & equipment needed........................................................................................................................2

Chapter 2 Installing Module in BDCOM Switches................................................................................................................3

Chapter 3 Connecting Module to a Network.........................................................................................................................4

3.1 Installing Single-port 100Base-TX Ethernet Module..............................................................................................4

3.1.1 Overview...................................................................................................................................................4

3.1.2 Information of interface card......................................................................................................................4

3.1.3 LS-1FE-TX Ethernet Module Connection with External Device................................................................5

3.2 Installing Single-port 100Base-FX(SM) Ethernet Module......................................................................................5

3.2.1 Overview...................................................................................................................................................5

3.2.2 LS-1FE-FX(SM) Ethernet Module Connection with External Device........................................................6

3.3 Installing Single-port 100Base-FX(MM) Ethernet Module.....................................................................................6

3.3.1 Overview...................................................................................................................................................6

3.3.2 LS-1FE-FX(MM) Ethernet Module Connection with External Device........................................................7

3.4 Installing Single-port 1000Base-TX Ethernet Module............................................................................................7

3.4.1 Overview...................................................................................................................................................8

3.4.2 LS-1GE-TX Ethernet Module Connection with External Device................................................................9

3.5 Installing Single-port 1000Base-LX Ethernet Module............................................................................................9

3.5.1 Overview...................................................................................................................................................9

3.5.2 LS-1GE-LX Ethernet Module Connection with External Device..............................................................10

3.6 Installing Single-port 1000Base-SX Ethernet Module.........................................................................................10

3.6.1 Overview.................................................................................................................................................10

3.6.2 LS-1GE-SX Ethernet Module Connection with External Device.............................................................11

3.7 Installing Single-port Gigabit GBIC Module Extension........................................................................................ 11

3.7.1 Overview.................................................................................................................................................11

3.7.2 LS-1GE-SX Module and Connection to the External Device..................................................................12

3.7.3 Insert GBIC Module.................................................................................................................................12

- I -

BDCOM switch module Hardware Installation Guide

Chapter 1 Overview of BDCOM Module

1.1 Module Overview

This section explains the interface module of the BDCOM switch.
BDCOM switch provides 2 extended Ethernet slots. Plug into the following interface

module as needed:

No. Type Name Label

1

Single-port 100Base-TX Ethernet Module

LS-1FE-TX

2

Single-port 100Base-FX(SM) Ethernet Module

3

Single-port 100Base-FX(MM) Ethernet Module

4

Single-port 1000Base-TX Ethernet Module

5

Single-port 1000Base-TX Ethernet Module

6

Single-port 1000Base-SX Ethernet Module

7

Single-port Gigabit GBIC Module Extension

1.2 Preparing to install the interface card

This chapter tells the care cases & preparing work before you begin, includs the
following sections:

Notes:

Please read this chapter carefully to avoiding possible injury to the body or any damage to the equipment.

1.2.1 Safety information

 Put the router in clear,dust-free,dry and safe area.

LS-1FE-FX(SM)
LS-1FE-FX(MM)
LS-1GE-TX
LS-1GE-LX
LS-1GE-SX
LS-1GBIC

 Avoid using overdue external force to pull the power supply line, interface cable.
 Do not wear loose clothing.
 Wear safety glasses if you are working under any conditions that might be

hazardous to your eyes.

 Suggest using UPS.
 Safety warning.
 Do not touch the unshielded telephone line.
 Do not insert the tie-in of telephone into the ethernet by mistake.

- 1 -

BDCOM switch module Hardware Installation Guide

 You should guarantee that the power of the power supply is powerful enough.
 Use the power safety.
 Do not insert/unlatch the cable with the power.
 Static protection: please wear anti-static loop in the process of installation.

1.2.2 Tools & equipment needed

1. Tools

 Flat-blade screw-driver.
 Cross screw driver.
 ESD-preventive wrist strap.
 Cable.
 Ethernet cable & special serial port interface cable
 Console port cable.
 Power cord.

2. Equipment

Configuration terminal （such as : analog PC）

- 2 -

BDCOM switch module Hardware Installation Guide

Chapter 2 Installing Module in BDCOM Switches

The section explains how to install interface module. Before installing interface module,
make sure the switch is turned off.

Note:

Interface module does not support hot plug. Hot plug may cause permanent damage to interface
module.

Operations:
(1) Turn off the power. To prevent damage caused by static, keep the switch and

personnel grounded.
(2) Unplug all the cables.
(3)

Use a flat head screwdriver to remove the piece of iron on the interface

module (see the following picture). Do throw away the piece of iron.

(4) Put the interface module in the guiding track. Slide it into the switch. (Refer to

the illustration below.)

(5) Slide the interface module and align it to the switch.
(6) Use the flat head screwdriver fasten the interface module and the switch.
(7) The following chapters explain different interface module cable connections and

LED status. Refer to the corresponding chapters for external connection.
(8) After installation, start installing software.

- 3 -

BDCOM switch module Hardware Installation Guide

Chapter 3 Connecting Module to a Network

3.1 Installing Single-port 100Base-TX Ethernet Module

Single-port 100Base-TX Ethernet module (LS-1FE-TX) adopts RJ45 interface standard.
It supports 10/100Mbps auto-sense and auto-MDI/MDIX, which may realize Ethernet
message transmission at 140m.

3.1.1 Overview

Single-port 100Base-TX Ethernet module port supports 10/100M auto-sense and.
auto-MDI/MDIX. Transmission distance:

 10Mbps: UTP 3/4/5/ (transmission distance is 140m)
 100Mbps: UTP 5 (transmission distance is 140m)

Figuer 3-1 Front view of Single-port 100Base-TX Ethernet module panel

3.1.2 Information of interface card

1. Cable of interface card

Table 3-1 Definition of RJ45 pin

Pin NO. Description Name Note

1 Data transmission positive TXD+ Output
2 Data transmission negative TXD- Output
3 Data receive positive RXD+ Input
6 Data receive negative RXD- Input

Single-port 100Base-TX Ethernet module supports auto-MDI/MDIX. This is able to
adopt UTP5 to connect to other Ethernet device.

- 4 -

BDCOM switch module Hardware Installation Guide

2. Single-port 100Base-TX Ethernet Module LED

No. Name Note

1

LINK

Indicate the connection status of RJ45.

2

ACT

Indicate transmission of RJ45.

3.1.3 LS-1FE-TX Ethernet Module Connection with External Device

3.2 Installing Single-port 100Base-FX(SM) Ethernet Module

Single-port 100Base-FX(SM) Ethernet module (LS-1FE-FX(SM)) transform
100Methenet message into optical message. Fiber optic transmission lengthen the
transmission of Ethernet transmission.

3.2.1 Overview

The configured optic module decides the transmission distance of Single-port
100Base-FX(SM) Ethernet module. By using different optic module, we are able to
realize different transmission distances. The manufacturer default transmission
distance for Single-port 100Base-FX(SM) is 15km. Users may realize farther
transmission according to their needs.

Figuer 3-2 Single-port 100Base-FX(SM) Ethernet Module Panel

- 5 -

BDCOM switch module Hardware Installation Guide

1. Single mode Ethernet fiber optical transceiver module pin

 TX: optical signal transferring end;
 RX: optical signal receiving end.

2. Single-port 100Base-FX(SM) Ethernet Module LED

No. Name Note

1

LINK

Indicate the connection status of the ports

2

ACT

Indicate transmission of the ports

3.2.2 LS-1FE-FX(SM) Ethernet Module Connection with External Device

Connect the Single-port 100Base-FX(SM) Ethernet module TX to megabit single mode
Ethernet optic module RX and connect the Single-port 100Base-FX(SM) Ethernet
module RX to the megabit single mode Ethernet optic module TX.

3.3 Installing Single-port 100Base-FX(MM) Ethernet Module

Single-port 100Base-FX(MM) Ethernet module (LS-1FE-FX(MM)) transform
100Methenet message into optical message. Optic fiber transmission lengthen the
transmission of Ethernet transmission.

3.3.1 Overview

Single-port 100Base-FX(MM) Ethernet module can transfer 2km. Users may select
Single-port 100Base-FX(SM) Ethernet module to realize farther transmission.

- 6 -

BDCOM switch module Hardware Installation Guide

Figuer 3-3 Single-port 100Base-FX(MM) Ethernet Module

1. Multi-mode Ethernet fiber optical transceiver module pin.

 TX: optical signal transferring end;
 RX: optical signal receiving end.

2. Single-port 100Base-FX(MM) Ethernet Module LED.

No. Name Note

1 LINK

Indicate the connection status of the
ports.

2 ACT Indicate transmission of the ports.

3.3.2 LS-1FE-FX(MM) Ethernet Module Connection with External Device

Connect the Single-port 100Base-FX(MM) Ethernet module TX to 100Base-FX(MM)
Ethernet fiber optical transceiver module RX and the RX to the TX.

3.4 Installing Single-port 1000Base-TX Ethernet Module

Single-port 1000Base-TX Ethernet module (LS-1GE-TX) adopts RJ45 interface
standard, which supports 10/100/1000Mbps auto-sense and auto-MDI/MDIX.

- 7 -

BDCOM switch module Hardware Installation Guide

3.4.1 Overview

Single-port 1000Base-TX Ethernet module port supports 10/100/1000M auto-sense
and auto-MDI/MDIX and adopts UTP 5 and is able to transfer 100m:

Figuer 3-4 Single-port 1000Base-TX Ethernet Module

1. Cable of interface card

Table 3-2 Definition of 1000Base RJ45 pin

Pin NO. Description Name Note

1 Data transmission positive TXD1+ Output
2 Data transmission negative TXD1- Output
3 Data receive positive RXD1+ Input
4 Data transmission positive TXD2+ Output

5

6 Data receive negative RXD1- Input
7 Data receive positive RXD2+ Input
8 Data receive negative RXD2- Input

Data transmission negative TXD2- Output

Single-port 1000Base-TX Ethernet module supports auto-MDI/MDIX. It is able to adopt
UTP 5 to connect to other Ethernet device.

2. Single-port 1000Base-TX Ethernet module LED

No. Name Note

1 LINK Indicate the connection status of RJ45.
2 ACT Indicate transmission of RJ45.

- 8 -

BDCOM switch module Hardware Installation Guide

3.4.2 LS-1GE-TX Ethernet Module Connection with External Device

3.5 Installing Single-port 1000Base-LX Ethernet Module

Single-port 1000Base-LX Ethernet module (LS-1GE-LX) transform 1000Methenet
message into optical message. Optic fiber transmission lengthen the transmission of
Ethernet transmission.

3.5.1 Overview

The configured optic module decides the transmission distance of Single-port
1000Base-LX Ethernet module. By using different optic module, we are able to realize
different transmission distance. The manufacturer default transmission distance for
Single-port 1000Base-LX is 10km. Users may realize farther transmission according to
their needs.

Figuer 3-5 Single-port 1000Base-LX Ethernet Module Panel

1. Gigabit single mode Ethernet optic module pin

 TX: optical signal transferring end.
 RX: optical signal receiving end.

- 9 -

BDCOM switch module Hardware Installation Guide

2. Single-port 1000Base-LX Ethernet Module LED

No. Name Note

1 LINK Indicate the connection status of the ports
2 ACT Indicate transmission of the ports

3.5.2 LS-1GE-LX Ethernet Module Connection with External Device

Connect the Single-port 1000Base-LX Ethernet module TX to 1000Base-LX Ethernet
fiber optical transceiver module RX and the RX to the TX.

3.6 Installing Single-port 1000Base-SX Ethernet Module

Single-port 1000Base-SX Ethernet module (LS-1GE-SX) transform 1000Methenet
message into optical message. Optic fiber transmission lengthen the transmission of
Ethernet transmission.

3.6.1 Overview

Single-port 1000Base-SX Ethernet module can transfer 550m. Users may select
1000Base-LX Ethernet module to realize farther transmission.

Figuer 3-6 Single-port 1000Base-SX Ethernet Module Panel

- 10 -

BDCOM switch module Hardware Installation Guide

1. Gigabit multi-mode Ethernet optic module pin

 TX: optical signal transferring end.
 RX: optical signal receiving end.

2. Single-port 1000Base-SX Ethernet Module LED

No. Name Note

1 LINK Indicate the connection status of the ports.
2 ACT Indicate transmission of the ports.

3.6.2 LS-1GE-SX Ethernet Module Connection with External Device

Connect the Single-port 1000Base-SX Ethernet module TX to 1000Base-SX Ethernet
fiber optical module RX and the RX to the TX.

3.7 Installing Single-port Gigabit GBIC Module Extension

Single-port Gigabit GBIC module extension transforms 1000Methenet message into
optical message. Optic fiber transmission lengthen the transmission of Ethernet
transmission. GBIC module supports hot plug. Users may insert different GBIC
modules as needed.

3.7.1 Overview

Single-port Gigabit GBIC module may insert into Single/Multi mode GBIC module to
realize diff.

GBIC module Description Max Transmission Distance

GBIC-SX Multi-mode GBIC module. 550m
GBIC-LX-10 Single mode GBIC module. 10km
GBIC-LX-40 Single mode GBIC module. 40km

- 11 -

BDCOM switch module Hardware Installation Guide

GBIC-ZX-80 Remote single mode GBIC module. 80km

erent transmission distance:

Figuer 3-7 Single-port Gigabit GBIC Module Extension Panel

1. Gigabit GBIC optic module pin

 Arrow pointing outside: optical signal transferring end.
 Arrow pointing inside: optical signal receiving end.

2. Single-port Gigabit GBIC Module LED

No. Name Note

1 LINK Indicate the connection status of the ports.
2 ACT Indicate transmission of the ports.

3.7.2 LS-1GE-SX Module and Connection to the External Device

Connect the Single-port Gigabit GBIC module TX to megabit single mode Ethernet
optic module RX and RX to TX.

3.7.3 Insert GBIC Module

Note:

GBIC is used to connect peripheral with gigabit Ethernet port to optic fiber, which supports hot plug.

- 12 -

BDCOM switch module Hardware Installation Guide

(1) Identify the GBIC module. Confirm whether it is single mode or multi-mode;
(2) Hold the front side of GBIC module;
(3) Follow the direction of the arrow on the module and insert into the GBIT slot;
(4) Open the rubber cover on the module when you need to connect the fiber.

Note:

cover the rubber cover when not connect the fiber to prevent dust from falling.

(5) Insert the fiber to GBIC module (be careful about the directions).

- 13 -