BCDVideo BCD-RGD-804P-MT User Manual

Download

Page 1

+1 847. 205.1922

info@bcdvideo.com

www.bcdvideo.com

BCD214-RGD-804P-MT

USER GUIDE

Page 2

BCD-RGD-804P-MT

table of contents

1 WEB Configuration 3

1.1 Preparing and Entry 3

1.1.1 Switch Default Configuration 3

1.1.2 Computer basic configuration requirement 3

1.1.3 Establish network connection 3

1.1.4 Check network weather connect between computer and switch 4

1.1.5 Login switch management interface 4

1.2 Web management interface 5

1.2.1 Basic information 5

1.2.2 Configuration 7

5.2.3 Monitor(Status Display)

5.2.4 Diagnostics

5.2.5 Maintenance

2 Command Line Management

2.1 Configure HyperTerminal

2.1.1 USB 115200-8-N-1 port connect with Device console port

2.2 Login equipment and basic command Query

2.2.1 System Information Query

2.2.2 Recovery factory default

2.2.3 Logout

2.2.4 Query / ModifyIP

2.2.5 Using own command help function

3 Technical Parameters

www.bcdvideo.com

Page 3

BCD-RGD-804P-MT

1 WEB configuration

1.1 Preparing and Entry

Configure the switch through Web pages, this chapter will take you through the equipment configuration process.

Aer completing the hardware installation, you need to ensure that the computer networks parameters to meet certain

conditions before accessing the Settings page.

1.1.1 Switch Default Configuration

The system default IP address is: 192.168.0.240, user name: admin; password: admin

1.1.2 Computer basic configuration requirement

Ethernet card installed, you can access the Internet through a network port. we recommend using a Computer (or better),

minimum display resolution support 1024 * 768 pixels for better view.

1.1.3 Establish network connection

Open network parameter configuration of Computer shown as below. Select the Internet Protocol (TCP / IP), enter the

Internet Protocol (TCP / IP) Properties window. Select the input IP address in addition to the default IP address and subnet

mask (255.255.255.0), click on the OK button to complete the operation.

(Note: The IP address and switch must be in the same subnet.)

Page 4

BCD-RGD-804P-MT

1.1.4 Check network whether connect between computer and switch

Use the ping command of Operating System, enter switch’s IP address, if reply normally, then network connectivity;

otherwise, check the network connection.

1.1.5 Login switch management interface

Running the browser, enter the switch default IP address (192.168.0.240) in address column, click Enter. Login dialog box,

as shown below, enter your user name and password (the default user name: admin, password: admin), click the OK

button or directly enter into the system configuration page. Aer a successful login interface as follows:

www.bcdvideo.com

Page 5

BCD-RGD-804P-MT

1.2 Web Management Interface

1.2.1 Basic information

Switch Configuration page is divided into Configuration, Manager, Diagnostics, Maintenance of four parts. As below:

Port State Overview. This area displays the current status of the device connection port. When the indicator is green

indicates that the corresponding port is connected, the indicator is gray, indicating the port not connected or enabled,

as shown below:

Navigation column: Click on a navigation column entry, the user can make the appropriate feature set and view,

as shown below:

Page 6

BCD-RGD-804P-MT

Configuration: Click the navigation column Configuration option, the system

will expand to show the relevant configuration interface, users can set the inter-

face-related functions.

Monitor: Click on the navigation column

Monitor option, the system will expand

to show the relevant status interface,

user-related functions can be provided in

the interface.

Diagnostics: Click on the navigation column Diagnostics option, the system

will expand the relevant components for switch device detection.

Maintenance: Click on the navigation column Maintenance option, the

system will be displayed in the management area related to user management

interface related functions can be provided in the interface.

www.bcdvideo.com

Page 7

BCD-RGD-804P-MT

1.2.2 Configuration

1.2.2.1 System

A. System Information

Enter [System]→[Information] navigation column, enter the system contact, system name, system location, time zone

oset system aer setting, click [Save] button to complete the basic configuration information.

Click [Reset] button, return to the data before system [Save]

Interface items introduction:

Interface items Configuration Introduction Factory configuration

System Contact 0~255 characters Equipment maintenance personal

contact information

System Name 0~255 characters Switch name, is used to specify

switch function (The first must be a letter, the last one cannot be a special sign)

System Location 0~255 characters Describing the location information

of device, such as production line 1

System Time zone Oset -720~720,unit:min oset between equipment time zone

and system time zone

Page 8

BCD-RGD-804P-MT

B. IP Address Configuration

Enter → [IP] navigation column, the page used to configure the address of the device management. The current status ad-

dress of the device, a mask, router will be displayed in the form. Aer modifying the contents of the form, click [Save] button

to complete the address modification or click [Reset], it will be restored to the original value form content unmodified.

Router is optional item, default is empty. Set relevant parameters, click [Save] button to complete the configuration.

IP interface: Interface items introduction (May dierent VLAN set dierent IP addresses, to meet the dierent hosts in

VLAN access to the switch).

Interface items Configuration Introduction Factory setting

Delete Select / not selected Select this option to delete an existing IP interface. not selected

VLAN 1~4095 number The VLAN associated with the IP interface. Only ports

in this VLAN will be able to access the IP interface. This field is only available for input when creating an new interface.

DHCP Select / not selected Enable the DHCP client by checking this box. If this

option isenabled, the system will configure the IP address and mask of the interface using the DHCP protocol.

Address Switch IP address The IPv4 address of the interface in dotted decimal

notation.

Mask Length 1-30 The destination IP network or host mask, in number of

bits (prefix length).

Add Interface Add an IP address settings

not selected

192.168.0.240

www.bcdvideo.com

Page 9

BCD-RGD-804P-MT

Click “Add Interface” Add a new IP interface.

IP router = Interface items introduction:

Interface items Configuration Introduction Factory Setting

Delete Select / not selected Select this option to delete an existing IP route. not selected

Network IP address The destination IP network or host address of this

route. Valid format is dotted decimal notation or a valid IPv6 notation. A default route can use the value

0.0.0.0 or IPv6 :: notation.

Mask Length 1-32 The destination IP network or host mask, in number of

bits (prefix length). It defines how much of a network address

that must match, in order to qualify for this route.

Gateway IP The IP address of the IP gateway. No

Click “Add Router” to add a new IP route interface.

C. SNTP Time Server Configuration

Enter [System] → [SNTP] Navigation, Time server configuration page, can be turned on when the remote NTP server,

and configure remote SNTP time server, click [Save] button to complete time server configuration.

24 The IPv4 address of the interface in dotted decimal

notation.

not selected

192.168.0.240

Interface items introduction:

Interface items Configuration Introduction Factory Setting

Mode Disable/Enable Indicates the NTP mode operation. Disable

Server Address Time server IP address Provide the IPv4 or IPv6 address of a NTP server. No

Page 10

BCD-RGD-804P-MT

D. Log Server Configuration

Enter [System] → [Log] navigation column, log configuration page, you can configure a remote logging server information,

the device logs information [Save] to a remote server, providing backup viewing. Select the server mode, set the server

address, select the log level, click [Save] button to complete the system logging configuration.

Interface items introduction:

Interface items Configuration Introduction Factory setting

Server Mode Disable/Enable Indicates the server mode operation. No

When the mode operation is enabled, the syslog message will send out to syslog server.

Server Address Log configuration

Disable Switch name, is used to specify switch function

(The first must be a letter, the last one cannot be a special sign)

Configure log server IP address No

IP address

5.2.2.2 Ports

Enter the [Ports] navigation column, you can view the connection status of each port, including: link connection, speed,

flow control and maximum frame size and other information, No 1-6 for the front panel port 100M / 1000M RJ45 ports, No

7-8 port for the data connection port, No 9-10 port Gigabit optical interfaces. Link status indication red indicates that the

link down state; green indicates that the link up state.

Port rate mode:

Ports can be selected as “Auto”, “Disabled”, “10mbps HDX”, “10mbps FDX”, “100Mpbs HDX”, “100Mpbs FDX”, “1Gbps FDX”;

This option may be set directly: Auto can automatic identification access type.

Flow Control: enable the port flow control, implement port flow control

The maximum frame size that can be configured port maximum transmission unit, the default is 9600. Select the relevant

parameters, click [Save] button to complete the port configuration. Also Click [Save] button to save changes. Click [Reset]to

cancel any changes made locally and return to previously saved values.

www.bcdvideo.com

Page 11

Interface items introduction:

BCD-RGD-804P-MT

Interface items Configuration Introduction Factory setting

Port Physical port number

Link Port status display, a red light indicates that the link is dis-

connected status, green indicates normal connection link

Speed Current Info/Warning/Error Display port status and mode Info

Speed Configured Disable Prohibition to transfer data through the port Disable

Auto Allows the port and the connected devices automatically

adjust speed according to IEEE 802.3u

10Mbps HDX In accordance with the rate selection, full / half duplex com-

10Mbps FDX

100Mbps HDX

100Mbps FDX

1Gbps FDX

Flow Control Current Rx

munication rate and to determine its mode of operation.

Indicates whether received the port flow control pause frames

Indicate port whether send the flow control pause frames X

Flow Control Configured

Maximum Frame Size

Excessive Collision Mode

Check / uncheck On / o flow control uncheck

64-10056Byte Set the port of the maximum data frame

Discard/Restart When the transfer conflict, whether retransmission of

9600

length

Discard

dropped packets: discard / retransmission

Page 12

BCD-RGD-804P-MT

5.2.2.3 Security

A. System password configuration

Enter [Switch] → [User] navigation column, this page is used to add users, change user account password;

important to remember the new password, the password is lost login prevent equipment failure.

Interface items Introduction

Add New User Add new user

User Name User name

Password password

Password(again) Confirm password

Privilege Level Level (The higher the value, the greater the level)

www.bcdvideo.com

Page 13

Modify the account password

In the User Interface, click the account that you want to modify;

Interface items introduction:

BCD-RGD-804P-MT

Interface items Introduction

Old Password Enter the password currently used, if the old password is entered

incorrectly, the new password is not enabled

New Password Enter the new password, the length of the bit characters <0-30>

characters

Confirm New Password Re-enter the same new password, or can not be enabled

B. Login authentication mode setting

Enter [Switch] → [Auth Method] navigation col-

umn, this page is used to set the manner in which

authentication when users access the switch .

When you select the authentication mode is “none”, no authentication enabled, you cannot login into the system.

When you select the authentication mode is “local”, enable user name and password to log in the system’s local user database.

When you select the authentication mode is “radius”, enable remote server for authentication.

Set relevant parameters, click [Save]to save changes.

Click [Reset] to undo any changes made locally and revert to previously saved values.

Page 14

BCD-RGD-804P-MT

Interface items Configuration Introduction Factory setting

Client Console/http As client user in console / web / telnet / ssh

mode access system

Methods none/local/radius Aer users access the system the authentication

modes: non-authentication / local authentication / remote server authentication, you can select local authentication and remote authentication server certificate as the same time

C. HTTPS Configuration

Enter [Switch] → [HTTPS configuration] navigation column, This page is used to enable the system’s web connection is

HTTP / HTTPS (secure HTTP). When users enable the HTTPS Meanwhile enable HTTPS automatic redirection function,

the system will automatically select web mode into the system.

When the user closes the HTTPS mode, the system will select HTTP mode into the system. It must enable HTTPS mode to

enable “automatic redirection” feature.

Select the relevant parameters, click [Save] to complete the HTTPS configuration; click [Reset] settings to the default values.

local

Interface items Configuration Introduction Factory setting

Mode Disable/Enable O / On HTTPS access switch Disable

Automatic Redirect Disable/Enable O / On automatic redirection between HTTP /

Disable

HTTPS

www.bcdvideo.com

Page 15

BCD-RGD-804P-MT

D. Access management configuration

Enter [Switch] →[Access Management] navigation column,Page is used to regulate the access management. Select Open

access control management mode, click on the “Add New Entry” button, typing “Start IP Address (beginning IP address)”,

“End IP Address (End IP address)”, select “HTTP / HTTPS”, “SNMP”, at least select a permissible service.

Click [Save] button to complete the access management configuration. Check delete selection on the corresponding

clause, click the check box to complete the deletion.

Interface items Configuration Introduction Factory setting

Mode Disable/Enable o/one access control management Disable

VLAN ID 1-4095 IP segment belongs VLAN 1

Start IP Address IP Address Access the start IP address 0.0.0.0

End IP Address IP address Access the end IP address 0.0.0.0

HTTP/HTTPS Select / not selected Selected, The IP address can accessed through HTTP/

HTTPS

SNMP Select / not selected Selected, The IP address can accessed through SNMP Not selected

Add New Entry: Click to add a new interface.

Delete:

Not selected

5.2.2.4 SNMP Configuration

A. SNMP system configuration

Enter 【SNMP configuration【→【System【navigation

column,If your network is configured with the SNMP server,

the switch can configure SNMP parameters, connect the

SNMP server. When selected SNMP v3 version needs to be

configured for specific functional parameters about SNMP

v3 security certification, groups, views and so on.

Page 16

BCD-RGD-804P-MT

Interface items Configuration Introduction Factory setting

Mode Disable/Enable Indicates the SNMP mode operation. Enable

Version SNMP V1/

SNMP V2C/ SNMP V3

Read Community 0-255 string Indicates the community read access string to per-

The allowed string length is 0 to 255, and the allowed content is the ASCII characters from 33 to

126. Write Community 0-255 string Indicates the community write access string to per-

Engine ID 16Decimal Indicates the SNMPv3 engine ID. The string must

B. SNMP Trap Configuration

Enter [SNMP configuration]→[Trap], This page is used to configure the SNMP Trap function. The feature set SNMP Trap Active

upload function followed protocol version, community, destination IP address, port number, and whether to use the Trap

Inform, if you use Trap Inform, the corresponding timeout, retransmission parameters, and safety Engine ID. While providing

local support for those events triggered Trap, such as: switch hot start, cold start, port status, authentication fails.

Public

Indicates the SNMP supported version. SNMP V2C

mit access to SNMP agent.

private

mit access to SNMP agent.

contain an even number(in hexadecimal format) with number of digits between 10 and 64, but all-zeros and all-'F's are not allowed. Change of the Engine ID will clear all original local users.

www.bcdvideo.com

Page 17

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Mode Disable/Enable Indicates the trap mode operation. Possible modes are:

Enabled: Enable SNMP trap mode operation. Disabled: Disable SNMP trap mode operation.

Add New Entry: add button, Click to expand Trap configuration view.

Disable

Page 18

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory

setting

Trap Config name 0~255 Byte Indicates which trap Configuration's name for configuring. The

allowed string length is 1 to 255, and the allowed content is

ASCII characters from 33 to 126. Trap Mode Disable/Enable Indicates the SNMP mode operation. Disable Trap Version SNMP V1/SNMP

V2C/SNMP V3

Trap Community Public/private

String

Trap Destination Address

Trap Destination Port

Trap Inform Mode Disable/Enable Indicates the SNMP trap inform mode operation. Disable Trap Inform Tim-

eout Trap Inform Retry

Times Trap Probe Security

Engine ID Trap Security En-

gine ID

Trap Security Name Indicates the SNMP trap probe security engine ID mode of oper-

Trap Event Indicates the SNMP trap security engine ID.

IP address Indicates the SNMP trap destination address. It allow a valid IP

Port address Indicates the SNMP trap destination port. SNMP Agent will send

0-2147 second Indicates the SNMP trap inform timeout. 3

0-255 time The allowed range is 0 to 2147. 5

Disable/Enable Indicates the SNMP trap inform retry times.

10-64 hexadecimal digits, not allowed all 0, all 1

Indicates the SNMP supported version. SNMP V2C

Indicates the community access string when sending SNMP trap

packet. The allowed string length is 0 to 255, and the allowed

content is ASCII characters from 33 to 126.

address in dotted decimal notation ('x.y.z.w').

SNMP message via this port, the port range is 1~65535.

The allowed range is 0 to 255. ProbeFail

ation.

Indicates the SNMP trap security name.

SNMPv3 traps and informs using USM for authentication and

privacy. A unique security

name is needed when traps and informs are enabled.

Configure SNMP trap on this page.

Public

162

None

C. SNMP Community Configuration

Enter [SNMP Configuration] → [Community] navigation column, Configure SNMPv3 community table on this page.

This function is used for only one IP address to restrict the information requested or received.

www.bcdvideo.com

Page 19

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Community 0~255 byte Community (Authenticate string) No

Source IP IP address Community Source IP address 0.0.0.0

Source Mask Subnet Mask Community Source Mask 0.0.0.0

D. SNMP Users Configuration

Enter [SNMP Configuration] → [Users] navigation column, Configure SNMPv3 user table on this page. Configure Authentication

security mode, security level, and data reported level of security, encryption mode for particular user when access identity

verification when accessing

Interface items introduction:

Interface items Configuration Introduction Factory setting

Engine ID 16Decimal Engine IDAs Engine ID authoritative SNMP it used to identify

SNMP entities, authentication and encryption

User Name 0-32 byte User name 0.0.0.0

Security Level NoAuth, NoPriv Security levels: no authentication, no privacy NoAuth, NoPriv

Auth, NoPriv authentication, no Privacy

Auth, Priv authentication, Privacy

Authentication Protocol

Authentication Password

Privacy Protocol DES/AES Choose packet encryption algorithm DES

Privacy Password 8-32 characters Packet encryption password NO

MD5/SHA Select the authentication encryption algorithm MD5

8-32 characters Authentication Password NO

800007 e5017f000001

Page 20

BCD-RGD-804P-MT

E. SNMP Group Configuration

Enter [SNMP configuration] → [Groups] navigation column, configure SNMPv3 group table on this page, This function is used

to set some of these groups and the security model, the authentication name. The Page Setup group, as can select use group

in Snmp-Access (Snmp Access Settings) page, out in option “Group Name” column, the configuration options for the user to

use Snmp access.

Interface items Introduction:

Interface items Configuration Introduction Factory setting

Security Model v1/v2c/usm SNMP group safety mode v1 group, v2c group, usm group

Security Name Public/Private SNMP group access permission public permission, private permission, default

user permission

Group Name 0-255 byte SNMP group name Default_ro_group

Default_rw_group

F. SNMP View Configuration

Enter [SNMP configuration] → [Views] navigation column, Configure SNMPv3 view table on this page. The main configuration

items are: the view name, OID subtree, include or exclude the OID subtree.

www.bcdvideo.com

Page 21

BCD-RGD-804P-MT

Interface items Introduction:

Interface items Configuration Introduction Factory setting

View Name 0-255 byte View name default_view

View Type Included/excluded View only included/exclude OID subtree node Included

OID Subtree Use "," separated string of numbers OID Mark .1

Default_rw_group

G. SNMP Access Configuration

Enter [SNMP configuration] → [Access] navigation column, Configure SNMPv3 access table on this page. Configure when a

group users access of the security mode , security levels, read-only view and read-write view. Click [Save]to save changes.

Click [Reset] to return to the default values.

Interface items Introduction:

Interface items Configuration Introduction Factory setting

Group Name 0-255 byte User group name to access default_ro_group

default_rw_group

Security Model any/v1/v2c/usm Select the security mode, any mode / v1 / v2c / usm for

user group

Security Level NoAuth, NoPriv Select security level for user group: No authentication

and no privacy

Auth, NoPriv Authentication and no privacy.

Auth, Priv Authentication and privacy.

Read View Name None/view configuration Select the desired view name for user Default view

Write View Name None/view configuration Select the desired write view name for user None

any

NoAuth, NoPriv

Default view

Page 22

BCD-RGD-804P-MT

5.2.2.5 Network

A. NAS Configuration

This page allows you to configure the IEEE 802.1X and MAC-based authentication system and port settings.

The IEEE 802.1X standard defines a port-based access control procedure that prevents unauthorized access to a network

by requiring users to first submit credentials for authentication. The IEEE802.1X standard defines port-based operation, but

non-standard variants overcome security limitations as shall be explored below.MAC-based authentication allows for authen-

tication of more than one user on the same port, and doesn’t require the user to have special 802.1X supplicant soware in-

stalled on his system. The switch uses the user’s MAC address to authenticate against the backend server. Intruders can create

counterfeit MAC addresses, which makes MAC-based authentication less secure than 802.1X authentication.

Enter [Network] → [NAS configuration] navigation column

www.bcdvideo.com

Page 23

BCD-RGD-804P-MT

Interface items Introduction:

Interface items Configuration Introduction Factory setting

Mode Disabled/Enabled Indicates if NAS is globally enabled or disabled on

the switch stack.

Reauthentication Enabled Check / uncheck Once selected, aer the authentication is successful,

a set time aer the Reauthentication Period, will be certified again

Reauthentication 0-255 byte SNMP group name Default_ro_group

Period 1-3600 second Recertification interval 3600

EAPOL Timeout 1-65535 second Identity EAPOL defined time frame resend request,

and this time on the MAC-based authentication is invalid

Aging Period 10-1000000 second Certification aging time, aer authentication, within

Aging Period of time no longer detect the device, the authentication will automatically lapse

Hold Time 10-1000000 second Aer the authentication fails, the re-certification

intervals, during this time do not accept the authentication request of the terminal

Disabled

Uncheck

300

Page 24

BCD-RGD-804P-MT

System configuration interface items introduction;

Interface items Configuration Introduction Factory setting

Mode Disabled/Enabled Indicates if NAS is globally enabled or disabled on the

switch stack.

Reauthentication Enabled Check / uncheck Once selected, aer the authentication is successful,

a set time aer the Reauthentication Period, will be certified again

Reauthentication 0-255 byte SNMP group name Default_ro_group

Period 1-3600 second Recertification interval 3600

EAPOL Timeout 1-65535 second Identity EAPOL defined time frame resend request, and

this time on the MAC-based authentication is invalid

Aging Period 10-1000000 second Certification aging time, aer authentication, within

Aging Period of time no longer detect the device, the authentication will automatically lapse

Hold Time 10-1000000 second Aer the authentication fails, the re-certification inter-

vals, during this time do not accept the authentication request of the terminal

Port configuration interface items introduction

Interface Configuration Introduction Factory setting

Port 1-n (# of physical

ports)

Admin State Force Authorized In this mode, when a client is connected to the port, the switch will

Force Unauthorized In this mode, when a client is connected to the port, the switch will

802.1X Using 802.1X authentication mode

MAC-Based Auth. Using MAC-Based authentication mode

To configure the switch port number port 1-n

automatically send an EAPOL success frame, you can access the network without authentication

send an EAPOL frame failure, any client cant access the network

Disabled

uncheck

300

Force Authorized Note: If set to a non Force Authorized port, you can not open the port Spanning tree, and Aggregation functions

Port State Globally Disabled NAS all Disabled

Link Down NAS all Enabled, but port can’t be connected

Authorized Port operates in Force Authorized mode, or work in only one request

mode, and the request authentication success

Unauthorized Port operates in Force Unauthorized mode, or work in only one re-

quest mode, and the request authentication not success

X Auth/YUnauth The port is a plurality of request mode, X client successfully authenti-

cates, Y client authentication is unsuccessful

Restart Reauthorized Authorized buttons only when the authentication mode in the open,

while the port state of 802.1X / MAC-Based Auth. When it is enabled, click Reauthorized immediately for certification has passed recertification

Reinitialize Reinitialize button only when the authentication mode in the open,

while the port state of 802.1X / MAC-Based Auth. When it is enabled, click Reinitialize initialize the client immediately forced to cut o the last certification, recertification

www.bcdvideo.com

Page 25

BCD-RGD-804P-MT

B. ACL (Access Control List) Configuration

ACL Port Configuration

Enter [ACL configuration] → [Ports] navigation column, Configure the ACL parameters (ACE) of each switch port. port only can

receive the frames matching ACE parameter. Also define eight per port policy number, each policy is defined dierent content,

you can configure the following parameters Series: Action , Permit / Deny to specify the type of data packet forwarding, Rate

Limiter ID , Port Redirect , 16 bandwidth control policies for network security configuration page definitions; Logging (logging):

Enable / Disable logging;

Page 26

BCD-RGD-804P-MT

Interface items Introduction:

Interface items Configuration Introduction Factory setting

Port 1-n (Number of physical ports) Number for Switch To configure the port 1-n

Policy ID 0-255 Select the policy to apply to this port 0

Action Permit/Deny Select filter out traic is forwarded or blocked Permit

Rate Limiter ID Disabled/0-16 Select which rate limiter ID to apply on this port Disabled

Port Redirect Disabled/port Number Select which port frames are redirected on. The allowed

values are Disabled or a specific port number and it can't be set when action is permitted. The default value is "Disabled".

Mirror Disabled/Enabled Frames received on the port are mirrored or not mir-

rored. Frames received on the port are stored in the System

Log or not logged.

Logging Disabled/Enabled Frames received on the port are stored in the System

Log or not logged.

Shutdown Disabled/Enabled If a frame is received on the port, the port will be dis-

abled or Enabled

State Disabled/Enabled When you select Enabled, when changing the port you

are using ACL user module, open ports When you select Disabled, when changing the port you are using ACL User Module, shut down the port

Counter Counts the number of frames that match this ACE. 0

Disabled

Enabled

ACL Rate Limiter Configuration

Enter [ACL configuration] → [Rate Limiters] navigation column,

is the ACL rate limiter configuration of port, The system sup-

ports 16 broadband strategy, speed range: 0-3276700 / PPS or

0,100,200,300 ... between 10000000kbps.

www.bcdvideo.com

Page 27

BCD-RGD-804P-MT

Interface items Introduction:

Interface items Configuration Introduction Factory setting

Rate Limiter ID 1-16 ACL rate limiter ID in use 1-16

Rate 0-3276700/PPS

0,100,200,300…10000000kbps

Unit pps/kbps Rate unit:

Click [Save] button when the configuration is complete ; Click [Reset] to return to the default values.

ACL Access control List

Enter [ACL configuration] → [Access Control List] navigation column, Check system access control lists.

Click to add ACE term of list.

Interface items Introduction:

Rate value configure 1

pps: packets / sec Kbps: kilobytes / sec.

pps

Page 28

BCD-RGD-804P-MT

Interface items Configuration Introduction Factory setting

Ingress Port All/Port1-n(Number of physical ports) All: ACE matching all Ingress port

Port1-n: ACE matching a Ingress port

Policy / Bitmask Policy: 0-255

Bitmask: 0x0-0x

Frame Type Any ACE match all frame types Any

EType ACE matching the Ethernet frame type,

ARP ACE matching ARP / RARP frame

IPV4 ACE match all IPV4 frame

IPV4/ICMP ACE matchingIPV4 frames with the ICMP

IPV4/UDP ACE matchingIPV4 frames with the UDP

IPV4/TCP ACE matchingIPV4 frames with the TCP

IPV4/other ACE matching the otherIPV4 frames

IPV6 ACE match all IPV6 frame

Action Permit Forwarding and Learning with ACE

Deny Discard the ACE matching frame

Designation ACE strategies code and bit mask

not match IP and ARP frames

protocol

except ICMP / UDP / TCP protocol

matching frame

All

Any

Permit

Filter Filtering the ACE matching frame

Rate Limiter Disabled/0-16 Select this port to be used for rate limit-

ing ID number

Port Redirect Disabled/port no Select a port frame whether redirected,

if redirected, set the redirection port, if Action is selected Permit, you can not choose to redirect

Mirror Disabled/Enabled In the frame of this port is not receiving

Mirror / mirrored

Counter The counter of frames and port settings

match ACE

List Change button:

+: ACE insert an item in the current row;

e: Edit ACE;

↑: Move the list ACE;

↓: Down ACE in the list

X: Delete ACE

+: In the bottom of the list to add an ACE item

Disabled

www.bcdvideo.com

Page 29

BCD-RGD-804P-MT

5.2.2.6 AAA authentication authorization accounting configuration

Enter [AAA configuration] navigation column. If you use a remote RADIUS authentication server, you can configure

corresponding RADIUS server parameters via this page, also can configure multiple servers, parameters include

common parameters for all servers and each server’s private parameters.

General parameters configuration

Interface items introduction:

Interface items Configuration Introduction Factory setting

Timeout 1-1000 second wait for the server response time before Retransmission request 5

Retransmit 1-1000 The maximum number of retransmissions request 3

Deadtime 0-1440 min intervals of a request aer the request fails 0

Key 0-63 byte Previous common password of RADIUS server and switch No

NAS-IP-Address IP address NAS logical IP address No

NAS-Identifier 0-255 byte NAS authentication string No

Page 30

BCD-RGD-804P-MT

Privacy server configuration

Interface items introduction:

Interface items Configuration Introduction Factory setting

Timeout 1-1000 second wait for the server response time before Retransmission request 5

Retransmit 1-1000 The maximum number of retransmissions request 3

Deadtime 0-1440 min intervals of a request aer the request fails 0

Key 0-63 byte Previous common password of RADIUS server and switch No

NAS-IP-Address IP address NAS logical IP address No

NAS-Identifier 0-255 byte NAS authentication string No

Privacy server configuration

Interface items introduction:

Interface items Configuration Introduction Factory setting

Delete

Hostname IP address RADIUS server IP address 1812

Auth Port Port No RADIUS server UDP port used for authentication 1813

Acct Port Port No RADIUS server UDP port used for accounting NO

Timeout 1-1000 second wait for the server response time before Retransmission request(in-

stead of generic parameters inside Timeout, if this parameter is empty, then common timeout use timeout parameter))

Retransmit 1-1000 The maximum number of retransmission request NO

Key 0-63 byte Previous common password of RADIUS server and switch

Click “Add New Server” to add a new RADIUS server.

www.bcdvideo.com

Page 31

BCD-RGD-804P-MT

5.2.2.7 Aggregation

A. Static Aggregation

Enter [Aggregation] → [Static] navigation column, The switch supports four kind Hash algorithm, four kinds of algorithms

mode can check, combination computing. Support 5 groups aggregation, each supports up to 10 ports. as shown: 1-2

opening set of aggregation; 3-4 opening set of aggregation and so on. Aggregation group member ports Please keep

configuration consistency, such as port speed mode, owned vlan information.

If some ports are open LACP dynamic convergence protocol, it can not manually configure the static convergence.

Page 32

BCD-RGD-804P-MT

Aggregation algorithm mode: Interface items introduction:

Interface items Configuration Introduction Factory setting

Source MAC Address Select/not select The Source MAC address can be used to calculate the

destination port for the frame. Check to enable the use of the Source MAC address, or uncheck to disable. By default, Source MAC Address is enabled.

Destination MAC Address Select/not select The Destination MAC Address can be used to calculate the

destination port for the frame.

IP Address Select/not select The IP address can be used to calculate the destination

port for the frame.

TCP/UDP Port Number Select/not select The TCP/UDP port number can be used to calculate the

destination port for the frame.

Aggregation configuration: This configuration is used to configure the Aggregation hash mode and the aggregation group.

The aggregation hash mode settings are global, whereas the aggregation group relate to the currently selected stackunit,

as reflected by the page header.

Interface items Configuration Introduction Factory setting

Group ID Normal/1-5 Indicates the group ID for the settings contained in the same row.

Group ID "Normal" indicates there is no aggregation. Only one group ID is valid per port.

Port Members Select/not select Each switch port is listed for each group ID. Select a radio button to

include a port in an aggregation, or clear the radio button to remove the port from the aggregation. By default, no ports belong to any aggregation group. Only full duplex ports can join an aggregation and ports must be in the same speed in each group.

not select

Normal

not select

www.bcdvideo.com

Page 33

BCD-RGD-804P-MT

B. LACP

Enter [Aggregation] → [LACP] navigation column, The switch supports dynamic aggregation port, aer port enable LACP,

Aggregation of both devices via protocol interaction gathering information, according to the parameters and status, auto-

matic matching link aggregation together send and receive data. Aer forming aggregation, switching equipment mainte-

nance aggregation link state, when the two sides configuration changes, automatically adjust or dissolve aggregated links.

If some ports have been static port aggregation, LACP dynamic convergence can not be achieved.

Page 34

BCD-RGD-804P-MT

Interface items Configuration Introduction Factory setting

Port 1-n (Number of physical

ports)

LACP Enabled Select/not select Controls whether LACP is enabled on this switch port.

Key Auto/Specific(1-65535) The Key value incurred by the port, range 1-65535 . The

Role Active/Passive The Role shows the LACP activity status. The Active will

Timeout Fast/slow The Timeout controls the period between BPDU transmis-

Prio 1-65535 The Prio controls the priority of the port. If the LACP part-

The switch port number. 1-n

LACP will form an aggregation when 2 or more ports are connected to the same partner.

Auto setting will set the key as appropriate by the physical link speed, 10Mb = 1, 100Mb = 2, 1Gb = 3. Using the Specific setting, a user-defined value can be entered. Ports with the same Key value can participate in the same aggregation group, while ports with dierent keys cannot.

transmit LACP packets each second, while Passive will wait for a LACP packet from a partner (speak if spoken to).

sions. Fast will transmit LACP packets each second, while Slow will wait for 30 seconds before sending a LACP packet.

ner wants to form a larger group than is supported by this device then this parameter will control which ports will be active and which ports will be in a backup role. Lower number means greater priority.

not select

Auto

Not select

Fast

32768

5.2.2.8 Loop Protection

Enter [Loop Protection] navigation column. This page allows the user to inspect the current Loop Protection

configurations and set relevant parameters, click [Save] button to save changes.

www.bcdvideo.com

Page 35

BCD-RGD-804P-MT

General Settings: Interface items introduction:

Interface items Configuration Introduction Factory setting

Enable Loop Protection

Transmission Time

Shutdown Time 0-604800 second The period (in seconds) for which a port will be kept dis-

Port Configuration: Interface items introduction:

Interface items Configuration Introduction Factory setting

Port 1- n The switch port number of Switch. 1-n

Enable Select/not select Controls whether loop protection is enabled on this switch

Action Shutdown Port loop is detected on a port, Shutdown the Port Shutdown Port

Disabled/Enabled Controls whether loop protection is enabled on this switch

port.

1-10 second The interval between each loop protection PDU sent on

each port. Valid values are 1 to 10 seconds.

abled in the event of a loop is detected (and the port action shuts down the port). Valid values are 0 to 604800 seconds (7 days). A value of zero will keep a port disabled (until nextdevice restart).

port.

Shutdown Port and Log

Log Only Loop detected, not shutdown port and log

Loop detected, shutdown port and log

Disabled

180

Select

Tx Mode Disabled/Enabled Select the port is send port of protected PDU, or the receiv-

ing end, Enabled as the sender, Disabled receiving end

5.2.2.9 Spanning Tree

A. STP Configuration

Enter [Spanning Tree] → [Bridge Settings] navigation

column, configure the system spanning tree on this page,

prevent loop. Enable RSTP protocol defaulted by system.

All configured parameters are applied to all STP of switch

configuration.

Set relevant parameters, click [Save] button to complete

the spanning tree protocol bridge configuration.

Click [Reset] button to restore the default settings.

Enabled

Page 36

BCD-RGD-804P-MT

Basic configuration: Interface items introduction:

Interface items Configuration Introduction Factory setting

Protocol Version STP/RSTP Spanning tree protocol version RSTP

Bridge Priority 0/4096/…../61440 Controls the bridge priority. Lower numeric values have

better priority. The bridge priority plus the MSTI instance number, concatenated with the 6-byte MAC address of the switch forms a Bridge Identifier.

Forward Delay 4-30 second The delay used by STP Bridges to transit Root and Desig-

nated Ports to Forwarding (used in STP compatible mode). Valid values are in the range 4 to 30 seconds.

Max Age 6-40second

And <= (Forward Delay-1) X 2

Maximum Hop Count

Transmit Hold Count

Advanced configuration:

Interface items Configuration Introduction Factory setting

6-40 This defines the initial value of remaining Hops for MSTI

1-10 The number of BPDU’s a bridge port can send per second.

The maximum age of the information transmitted by the Bridge when it is the Root Bridge. Valid values are in the range 6 to 40 seconds, and Max Age must be

information generated at the boundary of an MSTI region. It defines how many bridges a root bridge can distribute its BPDU information to.

When exceeded, transmission of the next BPDU will be delayed. Valid values are in the range 1 to 10 BPDU’s per second.

32768

Edge Port BPDU Filtering

Edge Port BPDU Guard

Port Error Recovery

Port Error Recovery Timeout

Select/not select Control whether a port explicitly configured as Edge will

transmit and receive BPDUs.

Select/not select Control whether a port explicitly configured as Edge will

disable itself upon reception of a BPDU. The port will enter the error-disabled state, and will be removed from the active topology.

Select/not select Control whether a port in the error-disabled state auto-

matically will be enabled aer a certain time. If recovery is not enabled, ports have to be disabled and re-enabled for normal STP operation. The condition is also cleared by a system reboot.

30-86400 second The time to pass before a port in the error-disabled state

can be enabled. Valid values are between 30 and 86400 seconds (24 hours).

not select

www.bcdvideo.com

Page 37

BCD-RGD-804P-MT

B. STP port configuration

Enter [Spanning Tree configuration] → [CIST Ports] navigation column, All ports by default are run Spanning Tree Protocol to

prevent loops. Port path cost default is Auto, users can manually specify, among 1-200000000, the smaller the value the more

priority path. Port priority, use in the spanning tree calculation process for 0/16/32/48 / ... / 224/240, the default is 128. Edge

port is use for switch connected to computer or connect network device without the spanning tree function. At this port

directly into the forwarding state, will not participate in the logical topology calculations.

Page 38

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port 1- n Switch port number 1-n

STP Enabled Select/not Select o/ on port STP Enabled Select

Path Cost Auto/ Specific:1-

200000000

Priority 0/16/32….240 Port Priority 128

AdminEdge Non-Edge/Edge Set the port connected device is STP bridge device or a

AdminEdge Select/not Select When selected enter the auto detect whether the port is

Restricted Role Select/not Select When Selected, the device serves as limit state, not select

Restricted TCN Select/not Select When Selected, TCP packet forwarding equipment limita-

BPDU Guard Select/not Select When Selected, the port does not receive a valid BPDU not Select

Point-to-Point Auto Device Automatic detection link is connected to this port is

Forced True Set this port to connect the device to force the link to point

Forced False Set this port to connect the device to force non-point link

Path cost, when selecting Auto the system will be based on the connection speed to use STP recommended values. When you select Specific, enter a value between 1-200000000 only as a path overhead.

non-bridge device, if non-bridge device, configured as Edge, will speed forwarding rate.

an edge port, according to the results of the monitoring configuration itself edge port.

to the root port

tions, namely, it does not forward the received TCN (Topology Change Notification) message to other ports

point to point

Auto

Non-Edge

Select

not Select

Auto

5.2.2.10 IPMC Configuration

A. IGMP Snooping basic configuration

Enter [IGMP Snooping configuration] → [Basic] navigation column, Common configuration can enable the multicast listener

function to achieve the IGMP packet detection, and for the host and corresponding port and establish the corresponding

multicast group address mappings. Broadcast unknown multicast function is configured for unregistered multicast packets

discarded or broadcast operations.

Port can be configured router port, does not age. When receiving an IGMP query is not configured for the port on the router

port, the switch that the port is connected with IGMP router (direct or indirect), on the port recorded as dynamic routing port.

When the switch receives IGMP reports will be forwarded to the router port.

Tick Snooping enabled, the port 1-2 routing port, fast leave options, click [Save] button to complete the IGMP Snooping,

Port configurations.

www.bcdvideo.com

Page 39

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Snooping Enabled

Unregistered IPMCv4 Flooding Enabled

IGMP SSM Range IGMP SSM range

Leave Proxy Enabled

Proxy Enabled tick/not tick Proxy On / O not tick

Router Port tick/not tick Set the port to route / non-routing port not tick

Fast Leave tick/not tick Enable / disable IGMP fast leave not tick

tick/not tick Enable the Global IGMP Snooping, disabled by default not tick

tick/not tick ON / OFF port flooding control, when IGMP Snooping is en-

tick/not tick Leaving the Proxy enable / disable not tick

tick abled, the flood control takes eect, when IGMP Snooping feature is disabled, can not be controlled flooding

Page 40

BCD-RGD-804P-MT

B. IGMP Snooping VLAN Configuration

Enter [IGMP Snooping Configuration] → [VLAN Configuration] navigation column, Click Add New IGMP VLAN button, enter

VLAN ID 1-2, tick Snooping enable option, click [Save] button to complete the IGMP Snooping VLAN configuration.

Click the Delete button before corresponding VLAN ID, click [Save] button to complete the IGMP Snooping vlan deleted.

IGMP Snooping VLAN number on the page displayed shows up to 99, 20 per default .by the following three keys can be

updated, view the list.

Refresh the display list

Previous displays list

Back displays list

Interface items introduction:

Interface items Configuration Introduction Factory setting

Delete Delete the corresponding IGMP Snooping VLAN list

VLAN ID 1-4095 Setting IGMP Snooping VLAN, range: 1-4095 No

Snooping Enabled

Querier Election Tick/not tick Enable / Disable IGMP querier aer opening can be select-

Querier Address IP address Setting IGMP query IP address, if not , the default address

Tick/not tick On / O the corresponding VLAN Snooping function, VLAN

not tick

up to make the function 32

tick ed as the interrogator, aer closing will not be selected for the query is

0.0.0.0 for the VLAN management, if the corresponding management address is not set, it defaults to the first VLAN management address, if not VLAN management address, the system defaults to 192.0 .2.1

www.bcdvideo.com

Page 41

BCD-RGD-804P-MT

5.2.2.11 LLDP Configuration

Enter [LLDP Configuration] → [LLDP] navigation column, The switch supports LLDP (Link Layer Discovery Protocol), can be

major capacity of the terminal equipment, management addresses, device identification, interface identifications and other

information organized into dierent TLV (Type / Length / Value: type / length / value) and Package (: link layer discovery pro-

tocol data unit link Layer Discovery Protocol Data Unit) published its standard MIB will give its directly connected neighbors,

neighbors receive this information in LLDP (Management Information Base: MIB) in the form save up for NMS inquiry and

determine the communication status of the link.

Page 42

BCD-RGD-804P-MT

LLDP Parameter configuration: Interface items introduction:

Interface items Configuration Introduction Factory setting

Tx Interval 5-32768 second The time interval of switch to send LLDP frames to the

neighbor

Tx Hold 2-10 times Multiple frame interval for configuring LLDP frame eective

time, the eective time = Tx Hold x Tx Interval

Tx Delay 1-8192 second Aer LLDP configuration change, time to re-transmission

and the last time interval between frames LLDP, <= 1/4 Tx Interval

TxReinit 1-10 second Time interval between LLDP stop frame and a new start

frame

LLDP Parameter configuration: Interface items introduction:

Interface items Configuration Introduction Factory setting

Port 1-n Switch port number 1-n

Mode Disabled The port is configured to not send or accept LLDP frame Disabled

Enabled Port is configured as both sending and receiving LLDP

frame

Rx Only Port is configured to only receive not send LLDP frame

Tx Only Port is configured to only transmit LLDP frames

Port Descr Tick/Not tick When ticked, the port description information transmit

contained TLV in LLDP frame, and did not tick the TLV information is not included in LLDP frame, transmission

Sys Name Tick/Not tick When ticked, the "System Name" will be included in LLDP

frame transmission, and did not tick the "System Name" is not included in LLDP frame, transmission

Sys Descr Tick/Not tick When ticked, the "System Description" will be included

in LLDP frame transmission, and did not tick the "System Description" is not included in LLDP frame, transmission

Sys Capa Tick/Not tick When ticked, the "System Properties" will be included in

LLDP frame transmission, and did not tick the "System Properties" does not contain the transmission in LLDP frame

MgmtAddr Tick/Not tick When ticked, "Managing Address" will be included in LLDP

frame transmission, and did not tick the "Manage Addresses" are not included in LLDP frame, transmission

Tick

www.bcdvideo.com

Page 43

5.2.2.12 POE

Enter [POE] navigation column, Set the value of the PoE.

BCD-RGD-804P-MT

Page 44

BCD-RGD-804P-MT

Power Over Ethernet Configuration: Interface items introduction:

Interface items Introduction Factory setting

Reserved Power determined by

Power Management Mode

Tx Delay Aer LLDP configuration change, time to re-transmission and the last time

TxReinit Time interval between LLDP stop frame and a new start frame 2

PoE Power Supply Configuration

Interface items Introduction Factory setting

Primary Power Supply[W] 2000 2000

PoE Port Configuration

Interface items Introduction Factory setting

PoE Mode Disabled/PoE/PoE+ Disabled

Priority Low/High Low

Class/Allocating /LLDP-MED Class

Actual Consumption/Reserved Power Reserved Power

interval between frames LLDP, <= 1/4 Tx Interval

Maximum Power[W] 15.4

5.2.2.13 MAC Table

Enter [MAC Table] navigation column, set the MAC address table dynamically updated timeout, MAC address table learning

mode, and manually add static MAC address table. Static MAC address table can add up to 64 MAC addresses.

Click<Add New Static Entry> button, enter the VLAN ID, a legitimate MAC address, select the port member, click [Save] button

to complete the configuration MAC address table.

www.bcdvideo.com

Page 45

BCD-RGD-804P-MT

Timeout configuration: Interface items introduction:

Interface items Introduction Factory setting

Disable automatic aging. Tick/not tick Aer tick the switch a certain time is not automatically

remove the MAC address not used in MAC address table

Age time 10-1000000

second

MAC address table configuration: Interface items introduction:

Interface items Introduction Factory setting

Auto Select Open port MAC address auto-learning function Selected

Disable Select Cancel port MAC address auto-learning function Not Selected

Secure Select Only static MAC address table can be learned, discard other MAC

addresses.

MAC address table dynamically updated timeout

not tick

300

Not Selected

Page 46

Static MAC address configuration: Interface items introduction:

Interface items Introduction Factory setting

BCD-RGD-804P-MT

Delete Click, delete the corresponding table

VLAN ID 1-4095 Added MAC address belong to VLAN ID 1

MAC Address MAC address MAC address add to MAC address table 00-00-00-00-00-00

Port Members Recheck 1-n

port

Click on “Add a New Static Entry” to add a new static MAC address entries to the MAC address table.

Aer selecting the port, MAC Address in the MAC address table added to the corresponding port in MAC address table

All not selected

5.2.2.14 VLANs Configuration

A. VLAN member IP configuration

Enter the [System Configuration] → [IP] navigation column, Vlan can create / delete IP, click [Save] button to save the

current configuration, click [Delete] button to delete VLAN entries. Click [Reset] button to restore the data before storage.

www.bcdvideo.com

Page 47

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction Factory setting

Delete Click, delete the corresponding table

VLAN ID 1-4095 Added MAC address belong to VLAN ID 1

MAC Address MAC address MAC address add to MAC address table 00-00-00-00-00-00

Port Members Recheck 1-n

port

Click “Add Interface ” to add a new VLAN IP.

Aer selecting the port, MAC Address in the MAC address table added to the corresponding port in MAC address table

All not selected

Page 48

BCD-RGD-804P-MT

B. VLAN Configuration

Enter [Configuration] → [VLANs Configuration] navigation column, can create / modify VLAN, and added / edited the port to

the appropriate VLAN.

If just use common VLAN function, this page only need to configure the default VLAN number (Port VLAN) ,other functions

without changes, except if you want to customize VLAN settings at Port VLAN , need to add a new VLAN number added to

back inside of Allowed Access vlans ;

Ingress Filtering: refers to the port receives the packets that do not match choose to drop or forwarded, the default port

input filtering function is disabled, that does not match the vlan packets received.

Frame Type: tag refers to the port receives packets with VLAN tag (and the VLAN ID tag should not be 0); untag refers to the

port only receives packets without tag labels.

If configure advanced QINQ features, port optional: unaware lc / c-portls / s-port / s-custom-port type several modes to

achieve dierent functions.

Click [Reset] button to return to the data before [Save]

www.bcdvideo.com

Page 49

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory

setting

Allowed Access vlans VLAN port Allowed access VLAN ID 1

Ether type for Custom S-ports

Port 1~N Ethernet port ID

Mode Access Access √

Port VLAN Range 1~4095 Configure the range of VLAN ID1~4095 1

Port Type Unaware Port as unaware VLAN tag port C-Port

S-Ports definition mode Port when as service port the VLAN Ethernet type 88A8

Trunk Configure when VLAN need Trunk

HYbrid Mixed (ring network use)

C-Port Port as custom port

S-Port Port as service port

S-Custom-Port Port as service/custom port

Ingress Filtering Refers to the port receives the packets that do not

Ingress Acceptance Tagged And Untagged/

Egress Tagging Untagged Port VLAN/

Tagged All / Untagged All

Allowed VLANs

Forbidden VLANs Forbidden VLAN Setting forbidden VLAN

match choose to drop or forwarded, the default port input filtering function is disabled, that does not match the vlan packets received

Set the port receive the frame type, Untagged Port VLAN: VLAN port only receives untagged frames; Tagged ALL: port receives frames tagged for all, Untagged All: some frame labels are not applied,

When setting the Trunk function need to set the allow the VLAN ID

All

Page 50

BCD-RGD-804P-MT

5.2.2.15 Private VLANs configuration

A. Private VLAN membership configuration

Enter [Private VLANs configuration] →[PVLAN Membership] navigation column, click [Add New Private VLAN] button, entry

PVLAN ID to 2 and 3,select the port membership, click [Save]”button to compete the private VLAN membership configuration.

Select the Delete option in front of the corresponding VLAN ID, click [Save] button to delete the private VLAN members.

Interface items introduction:

Interface items Configuration Introduction Factory setting

Delete Click, delete the corresponding items

Private VLAN ID 1-4095 Specifies to configure a private VLAN ID 1

Port Members Tick/not tick VLAN description information tick

Click “Add New Private VLAN ” to add a new private VLAN.

www.bcdvideo.com

Page 51

BCD-RGD-804P-MT

B. Private VLAN port isolation configuration

Enter [Private VLANs configuration] → [Port Isolation] navigation column, To implement Layer 2 isolation between packets,

and dierent ports can be configured to dierent VLAN, but do not waste the limited VLAN resources, using port isolation

feature, achieving isolation between ports within the same VLAN, users only need to put the port to the isolation group, you

can achieve isolation between Layer 2 data within the isolation group port. Port isolation provides users with a more secure

and flexible networking schemes.

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port Members Tick/not tick aer tick, the port isolated its VLAN and Private VLAN Not tick

VLAN

5.2.2.16 QoS configuration

A. Qos ingress Port classification

Enter [Port Classification] navigation column, this page allows you to configure the basic QoS Ingress Classification

settings for all switch ports. The main configuration items as: Qos class (QoS category), DP level (DP level).

Page 52

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port 1- n configure the switch port number 1-n

QoS class 0-7 Qos class number, 0 is the lowest priority category 0

DP level 0/1 Frame discard class, 0: no dropped frames; 1: drop frames

during congestion

PCP 0-7 802.1Q VLAN priority tag frames, if the port is VLAN aware

and the frame has a VLAN tag, this value will be inserted into the VLAN priority bits field VLAN tag. Otherwise it will insert the default VLAN priority

DEI 0/1 VLAN discard frames rating, 0: VLAN frame is not discarded;

1: discard the VLAN frame congestion

www.bcdvideo.com

Page 53

BCD-RGD-804P-MT

B. Qos ingress port Policing

Enter [Port Policing] navigation column, Configure the port rate of Qos policing,main configure items:

Rate, Flow Control

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port 1- n Switch Port ID need to configure 1-n

Enabled Select/not select Qos policy enabled, select: enabled Not select

Rate 100-1000000/ 1-3300 Rate value configure: 100-1000000Kbps or 1-3300pps 500

500 802.1Q VLAN priority tag frames, if the port is VLAN aware

and the frame has a VLAN tag, this value will be inserted into the VLAN priority bits field VLAN tag. Otherwise it will insert the default VLAN priority

Unit Kbps/pps Rate unit: pps: packets / sec

Kbps: kilobytes / sec.

Flow Control Select/not select On/o flow control Not select

kbps

Page 54

BCD-RGD-804P-MT

C. Qos egress port schedulers

Enter [Port Scheduler] navigation column, show QoS port data flow egress schedulers.

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port 1- n Switch Port ID need to configure 1-n

Mode Strict Priority /

Weighted

Weight Qn show line 1-5 weighted 500

Click port number 1, 2, 3… 10 enter to specific configure page Scheduler Mode configure to Strict priority,

interface show as below:

Port schedule mode Strict Priority

www.bcdvideo.com

Page 55

BCD-RGD-804P-MT

Scheduler Mode configure to Weighted,

interface show as below:

Page 56

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Scheduler Mode Strict Priority /Weighted Schedule mode optional Strict Priority

Queue Shaper Enable Select/not select On / O queue shaper enable not select

Queue Shaper Rate 100-1000000/ 1-3300 Queue rate configure:

100-1000000Kbps or 1-3300pps

Queue Shaper Unit Kbps/pps Rate unit pps: packets / sec

Kbps: kilobytes / sec.

Queue Shaper Excess Select/not select Aer select, queue can use excess bandwidth not select

Queue Scheduler Weight 1-100% Set the queue percentage weight 17

Queue Scheduler Percent show the queue percentage weight 17%

Port Shaper Enable Select/not select On/o port module Not select

Port Shaper Rate 100-1000000/ 1-3300 Port module rate:

100-1000000Kbps or 1-3300pps

Port Shaper Unit Kbps/pps Rate unit pps: packets / sec

Kbps: kilobytes / sec.

Change the option of the port number of upper right corner, you can configure all switch ports.

D. Qos Egress port shapers

Enter [Port Shaping] navigation column, show QoS port queue module configuration.

500

kbps

500

Kbps

www.bcdvideo.com

Page 57

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port Strict Priority /Weighted Schedule mode selected Strict Priority

Shapers Qn shows each queue configuration

Shapers Port shows each port configuration

E. Qos control list

Enter [QoS Control List] navigation column ,configure QoS control list. Click on the table rightmost button, the page will go

to a particular list item configuration interface.

Page 58

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

QCE# QoS list item Index

Port All/ port no Includ port

Key Parameters Frame Type

Key Parameters SMAC Any/Specific Select the recognized MAC address OUI

Key Parameters DMAC Any/UC/MC/BC Select a frame input data stream to identify the desti-

Key Parameters VID Any/Specific(1-4095)/

Key Parameters PCP Any/0,1,2,3,4,5,6,7/0-1,

Key Parameters DEI Any/0/1 Select the recognized discard flag for the frame of

Action Class 0-7 Add type value for frame matching key parameters 0

Action DPL Default/0/1 Add discard value for frame matching key parameters

Action DSCP Default/0-63 Add DSCP value for frame matching key parameters

Any/Ethernet/LLC/SNAP/ IPV4/IPV6

Range(VID1~VID2)

2-3,4-5,6-7,0-3,4-7

Select the recognized frame type for the input data flow

(Organization ID) for the input data flow

nation MAC address type: Any: Destination can be any type of MAC UC: Destination only to allow unicast MAC MC: Destination only to allow multicast MAC BC: Destination MAC only to allow broadcast

The frame VLAN ID range to be recognized of the input data stream, Any: All VLAN Specific: a specific VLAN Range: a VLAN range

Select the recognized priority for the input data flow Any

input data flow

(Default: Retain the original DPL)

(Default: Retain the original DSCP)

Any

Default

F. Qos storm control configuration

Enter [Storm Control] navigation column, configure QoS port storm control, open for unicast, multicast, rate limit broad-

cast storms, and set rate. The main configuration items : Unicast (unicast frames), Multicast (multicast frames), Broadcast

(broadcast frames).

www.bcdvideo.com

Page 59

BCD-RGD-804P-MT

Interface items Configuration Introduction Factory setting

Frame Type Data frame type, Unicast; Multicast: Broadcast

Enable Select/not select On/o storm control Not select

Rate 1-1024Kpps Select the data rate upper limit 1pps

5.2.2.17 Mirroring configuration

Enter [Mirroring] configuration navigation column, Port mirror-

ing, will complete mapping to the specified port for some port

or control packets flow, the designated port as the destination

port, the port is mapped source port mirroring, port mirroring

connected to the network analytical instruments , you can clear

analysis mirroring port packets without disrupting the business

of mirroring source port. Port mirroring is a convenient re-line

monitoring. All ports system can be configured as a mirrored

port, but the destination port mirroring can only configure one.

When a port is configured as a mirrored port, the corresponding

port cannot be configured as a source port. Source port means

that mirrored port, you can configure multiple destination port

mirroring to only configure one.

Page 60

BCD-RGD-804P-MT

Interface items introduction:

Interface items Configuration Introduction Factory setting

Port to mirror to Disabled/1- n Disabled Close mirroring function, 1-n select the

destination port

Port 1- n Switch physical port number 1-n

Mode Disabled Close Port Mirroring Disabled

Rx Only Only received frames are mirrored

Tx Only Only transmit frames are mirrored

Enabled Transmit and received frame are mirrored

Disabled

5.2.3 Monitor(Status Display)

5.2.3.1 System

A. System information

Enter [System] → [Information] navigation column, view system information on page.

www.bcdvideo.com

Page 61

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction

Contact System Configuration menu configure: maintenance personnel

contact

Name System Configuration menu configure: switch name

Location System Configuration menu configure: switch location

MAC Address Switch MAC address

Chip ID Switch chip ID

System Date System date

System Uptime System uptime

Soware Version Soware version

Soware Date Soware date

B. System log

Enter [System] → [Log] navigation column, on system log page, view some log information during the running

equipment process that is easy for the maintenance personnel analyze the problem.

Page 62

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction

Level Select log level:ALL;Info:;Warning;Error

Clear Level Remove log level:ALL;Info;Warning;Error;

ID Log index ID

Level Log level

Time Log Time date

Message Log message

Page operating button:

Refresh

Clear

|<<: view the first log

<<: view the Previous log

>>: view the next log

>>|: view the last log

C. Log detail

Enter [System] → [Detailed Log] navigation column,

entrylog, display system log detail on page.

www.bcdvideo.com

Page 63

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction

ID Select the log index to view

Level Log level

Time Log generate time

Message Log message

5.2.3.2 Thermal Protection

Enter [Thermal Protection],display the status information of device temperature on page.

Interface items introduction:

Interface items Introduction

Local Port Switch physical port number

Temperature Temperature

Port status Display the port link status

Page 64

BCD-RGD-804P-MT

5.2.3.3 Ports

A. Port status

Enter [Ports] → [State] navigation column, entry port state overview page, a graphical interface that shows the

connection status of the switch ports:

B. Port data traic overview

Enter [Ports] → [Traic Overview] navigation column, In the Port Statistics page, you can see the number of packets trans-

mitted and received for each port, the number of bytes transmitted and received error packets. When have too many error

message it indicates the working status of the port is poor, you need to check the cable connected to the port or other side

card if there are problems.

In this function, the user can check the <Auto Refresh> to refresh the data in real time, can also be manually Click <Refresh>

button to see the new data, <Clear> button to clear the statistics function provides.

www.bcdvideo.com

Page 65

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction

Port Switch physical port number

Packets Received Packets Received

Packets Transmitted Packets Transmitted

Bytes Received Bytes Received

Bytes Transmitted Bytes Transmitted

Errors Received Errors Received

Errors Transmitted Errors Transmitted

Drops Received Drops Received

Drops Transmitted Drops Transmitted

Fitered Received Fitered Received

C. Port QoS Statistics

Enter [Ports] → [QoS Statistics] navigation column, Displays status in dierent queues of each port on page.

Page 66

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction

Port Port ID

Qn Rx The number of queue received frame

QnTr The number of queue transmit frame

Click the port number, enter the corresponding port QoS status in the detailed statistics page, you can query detailed oper-

ation of each port, including receiving the transmitted packets, broadcast packets, error packets, etc., to facilitate network

management for network maintenance personnel. Drop-down navigation through the port to see the designated port traic

information, the user can check the <Auto-refresh> button to refresh the data in real-time information can also be manually

Click <Refresh> to see the new data, <Clear> button to clear the statistical data provided Features.

www.bcdvideo.com

Page 67

BCD-RGD-804P-MT

Total of transmitting and receiving packets: Interface items introduction:

Interface items Introduction

Rx Packages Total Rx Packages

Rx Octets Total Rx Octets

Rx Unicast Total Rx Unicast

Rx Multicast Total Rx Multicast

Rx Broadcast Total Rx Broadcast

Rx Pause Total Rx Pause

Tx Packages Total Tx Packages

Tx Octets Total Tx Octets

Tx Unicast Total Tx Unicast

Tx Multicast Total Tx Multicast

Tx Broadcast Total Tx Broadcast

Tx Pause Total Tx Pause

Frame number of Transmit and received of dierent frame length: The interface Item Description:

Interface items Introduction

Rx 64 Bytes Frame number of Rx 64 Bytes

Rx 65-127 Bytes Frame number of Rx 65-127 Bytes

Rx 128-255 Bytes Frame number of Rx 128-255 Bytes

Rx 256-511 Bytes Frame number of Rx 256-511 Bytes

Rx 512-1023 Bytes Frame number of Rx 512-1023 Bytes

Rx 1024-1526 Bytes Frame number of Rx 1024-1526 Bytes

Rx 1527- Bytes Frame number of Rx 1527- Bytes

Tx 64 Bytes Frame number of Tx 64 Bytes

Tx 65-127 Bytes Frame number of Tx 65-127 Bytes

Tx 128-255 Bytes Frame number of Tx 128-255 Bytes

Tx 256-511 Bytes Frame number of Tx 256-511 Bytes

Tx 512-1023 Bytes Frame number of Tx 512-1023 Bytes

Tx 1024-1526 Bytes Frame number of Tx 1024-1526 Bytes

Tx 1527- Bytes Frame number of Tx 1527- Bytes

Page 68

BCD-RGD-804P-MT

Transmit / receive queue transmit / receive the frame number: Interface Item Description:

Interface items Introduction

Qn Rx Receiving frame number in queue

Qn Rx Transmit frame number in queue

Transmitting / receiving error count: Interface Item Description:

Interface items Introduction

Rx Drops Number of received frame due to insuicient cache or congestion drops

Rx CRC/Alignment Number of received frame occurred CRC and alignment errors

Rx Undersize The number of short frames received undersize 64 bytes

Rx Oversize The number of frame received oversize the maximum frame

Rx Fragments The number of received frame with invalid CRC, frame length less than 64

Rx Jabber The number of received frame with invalid CRC, frame length over max frame

Rx Filtered The number of filtered outframes during forwarding process

Tx Drops Number of transmit frame due to insuicient cache or congestion drops

Tx Late/Exc. Coll. The number of transmit frames conflict then drop during transmission

D. Port QoS Control list

Enter [Ports] → [QCL Status] navigation column, display all QoS control table on page.

www.bcdvideo.com

Page 69

BCD-RGD-804P-MT

Interface items introduction:

Interface items Introduction

User User name

QCE# QoS list index

Frame Type Identify the input frame type:Any/Ethernet/LLC/SNAP/IPV4/IPV6

Port The Qos controls apply to which ports

Action Class To add QoS type value for" parameter configuration to match the input frame,"

Action DPL To add QoS discard flag for" parameter configuration to match the input frame,"

Action DSCP To add DSCP value for" parameter configuration to match the input frame,"

Conflict Status indicator whether conflict with other QoS control items

5.2.3.4 PoE

Interface items introduction:

Interface items Introduction

PD class 1\2\3\4…

Power Requested Required power dissipation

Power Allocated Power Allocated

Power Used Actual power usage

Current Used Actual current usage

Priority Low/High

Port Status The PoE available is green, the PoE is not available is red

Page 70

BCD-RGD-804P-MT

5.2.3.5 Security

A. Access Management Statistics

Enter [Access Management Statistics] navigation column, display access management statistics on page. Use can

select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the

new data, <Clear> button to clear the statistics function provides.

Interface items introduction:

Interface items Description

Interface Access management interface type: HTTP/ HTTPS/SNMP

Received Packets Number of received packets from port aer turned on access management mode

Allowed Packets Number of allowed port aer turned on access management mode

Discarded Packets Number of discarded packets from port aer turned on access management mode

B. Network Port Security

Enter [Port Security] → [Switch] navigation

column, display port switch security on

page. User can select<Auto-refresh>but-

ton to refresh data in real time, Can also be

manually Click <Refresh> button to see the

new data.

www.bcdvideo.com

Page 71

BCD-RGD-804P-MT

Interface items introduction:

Interface items Description

User Module Name The module name can request a port security services

Abbr User name Single-letter abbreviations

Port Switch physical port number

Users User module abbreviations

MAC Count The current number of learned MAC addresses

Port state

Enter [Port Security] → [Port] navigation column, display specific port state on page, User can select

<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Interface items introduction:

Interface items Description

MAC Address & VLAN ID Port learned MAC address and VLAN ID

State Indicates whether a matching MAC address of the frame is forwarded or blocked

Time of Addition The first occurrence time on matching the MAC address

Age/Hold MAC address hold time

NAS state

Enter [NAS state] → [Switch] navigation column, display switching state of network access server on page, User can select

<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Page 72

Interface items introduction:

BCD-RGD-804P-MT

Interface items Introduction

Port Switch physical port number, click to the details page

Admin State adopt authentication mode

Force Authorized: In this mode, when a client is connected to the port, the switch will auto-

Force Unauthorized: In this mode, when a client is connected to the port, the switch will

802.1X: Using 802.1X authentication mode

MAC-Based Auth.: Using MAC-based authentication mode

Port State Port state:

Globally Disabled: NAS all Disabled

Link Down: NAS all Enabled, but port cant link

Authorized: Port operates in Force Authorized mode, or work in only one request mode,

Unauthorized: Port operates in Force Unauthorized mode, or work in only one request

X Auth/Y Unauth: port in mange request mode,X user authentication success user authenti-

Last Source The last receiving source from EAPOL frame

Last ID The last receiving user name from response authentication EAPOL frame

www.bcdvideo.com

Page 73

BCD-RGD-804P-MT

ACL Status

Enter [ACL Status] navigation column, on statistics page, can view related security information, Use view all kinds network

security information through select the drop-down navigation Combined, Static, IPMC, LOOP, conflict. User can select

<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Interface items introduction:

Interface items Introduction

User Indicate to access list user

Ingress Port Access ingress input port: All/Port1-n

Frame Type Any: ACE matching all frame type

Type: ACE matching Ethernet type frame not IP frame and ARP frame

ARP: ACE matching ARP/RARP frame

IPV4: ACE matching all IPV4 frame

IPV4/ICMP: ACE matching IPV4 frame with ICMP protocol

IPV4/UDP: ACE matching IPV4 frame with UDP protocol

IPV4/TCP: ACE matching IPV4 frame with TCP protocol

IPV4/other: ACE matching IPV4 frame with other protocol except ICMP/UDP/TCP

IPV6: ACE matching all standard IPV6 frame

Action Permit: forward and learn the frame matching ACE

Deny: discard the frame matching ACE

Filter: filter the frame matching ACE

Rate Limiter Disabled/0-16: rate limit ID use on port

Port Redirect Disabled/Port ID: Whether Port Frame is re-directed, if redirect ,redirect port

Mirror Disabled/Enabled【The frame Be mirrored/not mirror receiving from the port

CPU Packet matching ACE forward to CPU

CPU Once The first packet matching ACE forward to CPU

Counter Packet counter matching ACE

Conflict Firmware state

Page 74

BCD-RGD-804P-MT

C. AAAstatus

Enter [AAA] → [RADIUS Overview] navigation column, If the network has been configured remote server radius,

you can view the relevant certification packet statistics from this page.

Interface items introduction:

Interface items Introduction

# NAS service ID, click to detail

IP Address Server IP address

Status Disable: server o

Not Ready: server on without IP packet

Ready: server on operating IP packet, RADIUS module is ready to accept access

Dead (X seconds Le): invalid time

Enter [AAA] → [RADIUS Details] navigation column, display the authentication state of RADIUS server on page, User can

select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

www.bcdvideo.com

Page 75

BCD-RGD-804P-MT

Accept packet: interface items description:

Interface items Description

Access Accepts Receiving packet number from server

Access Rejects Receiving packet number from server

Access Challenges Receiving access password packets from server

Malformed Access Responses Receiving packets number which non-compliant and unknown from server

Bad Authenticators Receiving authentication response packets number which including invalid authentication

unknown Types Authentication port receiving number of unknown packets which transmit from the server

Packets Dropped Authentication port receiving number of discard packets which transmit from the server

Transmit packet: interface items description:

Interface items Description

Access Accepts The number of access requests packets sent to the server

Access Retransmissions The number of Access Retransmissions packets sent to the server

Pending Requests The number of request packet sent to the server has not been a response but not overtime

Timeouts Authentication timeout Number

Other information: interface items description:

Interface items Description

IP Address Authentication server IP address

State state:

Disable: server o

Not Ready: server on without IP packet

Ready: server on operating IP packet, RADIUS module is ready to accept access

Dead(X seconds Le): invalid time

Round-Trip Time Recent access response, access password, the access request interval

Page 76

BCD-RGD-804P-MT

5.2.3.6 LACP state

A. LACP system status

Enter [LACP] → [System Status] navigation column, on this status page, can see the operating status on the port

agreement, the group number of automatic aggregation, local port, peer communication key member number

and other information.

Interface items description:

Interface items Description

Aggr ID Aggregation Examples ID

Partner System ID Aggregation system ID

Partner Key

Last changed

Local Ports indicator which ports including in aggregation port

B. LACP port status

Enter [LACP] → [Port Status] navigation column, This page displays LACP physical port information ,User can select

<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Communication key

Aggregation changing time

www.bcdvideo.com

Page 77

BCD-RGD-804P-MT

Interface items description:

Interface items Description

Port Switch physical port ID

LACP LACP status【Yes: LACP on and connected port;No【LACP o and port disconnected

Key

Aggr ID

Partner System ID Aggregation system ID

C. LACP port statistics

Enter [LACP] → [Port Statistics] navigation column, This page displays the physical port LACP reception, transmis-

sion dropped packets, User can select<Auto-refresh>button to refresh data in real time, Can also be manually Click

<Refresh> button to see the new data.

Communication key

Aggregation Examples ID

Interface items description:

Interface items Description

Port switch physical port ID

LACP Received Port Received the number LACP frame

LACP Transmitted Port transmitted the number LACP frame

Discarded Port discard the number of illegal LACP frame

Page 78

BCD-RGD-804P-MT

5.2.3.7 Loop Protection

Enter [Loop Protection] navigation column, display loop protection status on page,User can select

<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Interface items description:

Interface items Description

Port Switch physical port number

Action Protective action of port configuration

Transmit Transmit mode of port configuration

Loops loops time on port

Status Current loop protective status

Loop current port whether in loop status

Time of Last Loop The last time detect the loop

5.2.3.8 Spanning Tree

A. Spanning Tree Bridge status

Enter [Spanning Tree] → [bridge status] navigation column, can view: bridge ID, Root bridge ID, port path cost and oth-

er information, User can select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh>

button to see the new data.

www.bcdvideo.com

Page 79

BCD-RGD-804P-MT

STP bridge status detail :Interface items description:

Interface items Description

Bridge Instance STP bridge instance type

Bridge ID Bridge instance ID

Root ID Current root ID

Root Cost Root path cost

Root Port Designated port for the root bridge

Regional Root Be selected to regional root bridge ID

Internal Root Cost Internal root bridge path cost

Topology Flag Topology change status

Topology Change Count Topology change count

Topology Change Last Changing time for last topology

Page 80

BCD-RGD-804P-MT

CIST port and aggr status: Interface items description

Interface items Description

Port Switch STP valid port number

Port ID Port ID to be used for STP

Role The current use of STP port role

State The current STP port status

Path Cost The current STP port path cost

Edge Edge port instructions, Yes: port edge port; No: ports are non-edge port

Point-to-Point The current state of the STP is point to point

Uptime The last uptime of bridge port

B. Spanning Tree Port status

A. Spanning Tree Bridge status

Enter [Spanning Tree] → [Port Status] navigation column, can view each STP port status. Including STP role, the

forwarding state, updated information, User can select<Auto-refresh>button to refresh data in real time, Can

also be manually Click <Refresh> button to see the new data.

www.bcdvideo.com

Page 81

BCD-RGD-804P-MT

Interface items introduction:

Interface items Description

Port switch physical port no

CIST Role current STP port role

CIST State current STP port status

Uptime The last uptime of bridge port

C. Spanning Tree Port statistics

Enter [Spanning Tree] → [Port Statistics] navigation column, this page shows the STP packet statistics, User can

select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the

new data.

Interface items introduction:

Interface items Description

Port Switch physical port number

Transmitted MSTP Port transmitted the number of MSTP BPDU

Transmitted RSTP Port transmitted the number of RSTP BPDU

Transmitted STP Port transmitted the number of STP BPDU

Transmitted TCN Port transmitted the number of TCN BPDU

Received MSTP Port received the number of MSTP BPDU

Received RSTP Port received the number of RSTP BPDU

Received STP Port received the number of STP BPDU

Received TCN Port received the number of TCN BPDU

Discarded Unknown Port discarded the number of unknown STP BPDU

Discarded Illegal Port discarded the number of illegal STP BPDU

Page 82

BCD-RGD-804P-MT

5.2.3.9 IPMC status

A. IGMP Snooping status

Enter [IGMP Snooping] → [Status] navigation column, show IGMP Snooping on page, User can select<Auto-refresh>

button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Statistics status: Interface items introduction:

Interface items Description

VLAN ID VLAN ID

Querier Version Working Query Version

Host Version Working Host Version

Querier Status Querier Status

Queries Transmitted The number of transmitted query frame

Queries Received The number of received query frame

V1 Reports Received The number of received V1 Report frame

V2 Reports Received The number of received V2 Report frame

V3 Reports Received The number of received V3 Report frame

V2 Leaves Received The number of received V2 leave frame

www.bcdvideo.com

Page 83

BCD-RGD-804P-MT

Router port: Interface items instruction:

Interface items Description

Port Switch port ID

Status Indicator route port

B. IGMP Groups Information

Enter [IGMP Snooping] → [Groups Information] navigation column, show IGMP Snooping group information on page,

User can select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see

the new data.

Interface items instruction:

Interface items Description

VLAN ID VLAN ID

Groups Group address

Port Members Group including port

Page 84

BCD-RGD-804P-MT

5.2.3.10 LLDP status

A. LLDP neighbors

Enter [LLDP] → [Neighbors] navigation column, aer the device switched LLDP (Link Layer Discovery Protocol) function,

you can view the neighbor information on this page, including the port, the system name and other information. User can

select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to see the new data.

Interface items introduction:

Interface items Description

Local Port Receiving the port number of LLDP frame

Chassis ID Neighbor’s LLDP frame included Chassis ID value

Port ID Neighbor’s LLDP frame included port No

Port Description Neighbor transmitted the port description

System Name Neighbor published system name

System Capabilities Neighbor published system capabilities

Management Address Neighbor IP address

www.bcdvideo.com

Page 85

BCD-RGD-804P-MT

B. LLDP Port status

Enter [LLDP] → [port status] navigation column, page show LLDP counter, User can select <Auto-refresh> button to refresh

data in real time, Can also be manually Click <Refresh> button to see the new data.

Global Counter : Interface items instruction:

Interface items Description

Neighbour entries were last changed Receiving the port number of LLDP frame

Total Neighbours Entries Added Neighbor’s LLDP frame included Chassis ID value

Total Neighbours Entries Deleted Neighbor’s LLDP frame included port No

Total Neighbours Entries Dropped Neighbor transmitted the port description

Total Neighbours Entries Aged Out Neighbor published system name

Page 86

BCD-RGD-804P-MT

Local Counter : Interface items instruction:

Interface items Description

Local Port Port of local received and transmitted frame

Tx Frames The number of LLDP frames transmitted

Rx Frames The number of LLDP frames received

Rx Errors The number of wrong LLDP frames received

Frames Discarded The number of aer receiving the discard LLDP frames

TLVs Discarded The number of discarded TLV information sheet

TLVs Unrecognized The number of unrecognized TLV information

Org. Discarded The number of Organized TLV information

Age-Outs Valid time of LLDP

5.2.3.11 MAC Table

Enter [MAC Table] navigation column, On this page you can view all the Layer switch MAC address forwarding, port, MAC

address, VLAN and other entries. User can select<Auto-refresh>button to refresh data in real time, Can also be manually

Click <Refresh> button to see the new data.

www.bcdvideo.com

Page 87

BCD-RGD-804P-MT

Interface items instruction:

Interface items Description

Type MAC address type of Related MAC items,Static;Dynamic

VLAN VLAN ID of Related MAC items

MAC address MAC address of Related MAC items

Port Members Corresponding port of Related MAC items

5.2.3.12 VLANs status

A. VLAN membership

Enter [VLANs] → [VLAN Membership] navigation column, show VLAN membership information on page.User

can select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh> button to

see the new data.

Interface items instruction:

Interface items Description

VLAN ID VLAN ID of corresponding port

Port Members VLAN ID including port

Page 88

BCD-RGD-804P-MT

B. VLAN port

Enter [VLANs] → [VLAN Port] navigation column, page show VLAN port status, Dropdown navigation options Static, NAS,

MSTP, Combined. User can select<Auto-refresh>button to refresh data in real time, Can also be manually Click <Refresh>

button to see the new data.

Interface items instruction:

Interface items Description

Port Switch port ID

Port Type VLAN type indication port

Unaware port as VLAN tag port which The number of LLDP frames received

C-Port port as user port The number of wrong LLDP frames received

S-Port port as service port The number of aer receiving the discard LLDP frames

S-Custom-Port as user/service port The number of discarded TLV information sheet

Ingress Filtering Indicates whether filter the ingress frame:

Disabled: filtering Close Enabled: filtering function is enabled

Frame Type port ingress the accepted frame type:

ALL: port accepted all frame Tagged: port only accept frame with VLAN tag, Untagged: port only accept frame without VLAN tag

Tx Tag transmit the status of filtering frame: tag/ remove tag

UVID No label VLAN ID

Conflicts It indicates whether there is a conflict VLAN

www.bcdvideo.com

Page 89

BCD-RGD-804P-MT

5.2.4 Diagnostics

Diagnostics navigation column, including: ping and VeriPHY function.

5.2.4.1 Ping

Enter [Ping] navigation column, This can check the network connec-

tivity, if the network is normal, ping detection will respond to ICMP

echo packets. Enter the IP address, PING length, count, spacing pa-

rameters click <Start> button to start testing, you can display the in-

formation correctly.

Interface items instruction:

Interface items Description

IP Address Set the tested destination IP address

Ping Length Set Ping packet length, range: 2-1452, default is 56bytes

Ping Count Set the count of send Ping packets, range: 1-60, default is 5

Ping Interval Set Ping packet sending interval, range: 0-30, default is 1

Page 90

BCD-RGD-804P-MT

5.2.4.2 VeriPHY Diagnostics

Enter [VeriPHY diagnostics] navigation column, It can detect electrical cable ,communication under normal will show Ok

Interface items instruction:

Interface items Description

Port Switch Ethernet port ID

Pair A (B, C, D) Cable Dierential pairs connected state

OK: normal The number of LLDP frames received

Open: Open circuit The number of wrong LLDP frames received

Short: Short circuit The number of aer receiving the discard LLDP frames

Short A (B, C, D): short with A (B, C, D) cable Cross A (B, C, D): short with A (B, C, D) cable

Length A (B, C, D) Cable length XXX m

The number of discarded TLV information sheet

www.bcdvideo.com

Page 91

BCD-RGD-804P-MT

5.2.5 Maintenance

5.2.5.1 Restart Device

Enter [Restart Devic] Navigation Column, When restarted aer set the system MAC address etc., it is recommended to

restart the device to take eect.

5.2.5.2 Factory Defaults

Enter [Factory Defaults] Navigation Column, When need to revert to the original system defaults can choose to restore

the factory configuration functions. The default configuration for all configuration and IP address will become equip-

ment factory.

5.2.5.3 Soware

A. Upload (firmware download)

Enter [Soware] → [Upload] Navigation Column, Version Upgrade for upgrading switch version, aer the upgrade need

to restart the device.

Page 92

B. Image Select

Enter [Image Select],can activate the backup image.

BCD-RGD-804P-MT

5.2.5.4 Configuration

Note: The device all changes need to be saved here, otherwise changes will not take eect;

Enter [Configuration] → [Save startup-config] Navigation Column, Save the current configuration, if not save, restart device

will not take eect on equipment configuration.

Enter [Configuration] → [Download]

Navigation Column, can upload current

equipment configuration.

www.bcdvideo.com

Page 93

BCD-RGD-804P-MT

Enter [Configuration] → [Upload] Navigation Column, can upload the previous configure file to switch by upload function

to achieve configuration updates.

2 Command Line Management

Beside WEB management, Amber Series also support command line management

2.1 Configure HyperTerminal

2.1.1 USB (115200-8-N-1) port connect with Device console port

Page 94

1. There are many ways to access

the serial management port of

Switch. For example, Hyper Termi-

nal, SecureCRT,

Putty and so on. SecureCRT so-

ware will be used in the descrip-

tion below.

BCD-RGD-804P-MT

2. Select the COM port to use, and

click “OK.”

3. Set the appropriate serial port

parameters as follows, and then

click “OK.”

www.bcdvideo.com

Page 95

BCD-RGD-804P-MT

3. To powered the switch, you will see the following prompt message in serial terminal interface:

2.2 Login equipment and basic command Query

Note: The command can be entered only the first four characters, the other can be used as usual omitted;

2.2.1 System Information Query

Command: Show version

2.2.2 Recovery factory default

Command: reload defaults

Page 96

BCD-RGD-804P-MT

2.2.3 Logout

Enter “/” Return to the root directory of the command prompt; then enter “Logout”, that is exit to the login screen;

2.2.4 Query / ModifyIP

Command-line prompt to enter a user name and password, enter the appropriate commands into the relevant settings

and queries. (At the command prompt, type “?” Or “help” to get help)

The following equipment for the VLAN1 IP

2.2.5 Using own command help function

To sum up, configure other feature can be successfully loggedthe command prompt configure by the system prompts,

enter the ‘tab’key to display prompts information as below.

www.bcdvideo.com

Page 97

BCD-RGD-804P-MT

3 Technical Parameters

Technical

Ethernet standard

MAC address table 8192

Priority 8

flow control IEEE 802.3x Flow Control and Back-pressure

Treatment Store-and-Forward

Interface

RJ45 Ports 10/100//1000 Base-T(X), Auto MDI/MDI-X

Fiber Ports 1000 Base-X 100 Base-FX

Power Supply

Power input PWR1: 45~57VDC

Power reverse protection Present at terminal block

Power Consumption 10W(No POE)

POE/POE+ IEEE 802.3af, 802.3at

POE/POE+output power

802.3 - 10Base-T,

802.3u - 100Base-TX, 100Base-FX,

802.3z - 1000Base-LX/SX,

802.3ab - 1000Base-TX,

802.3ad - Link Aggregation Control Protocol,

802.3x - Flow Control,

802.1D - Spanning Tree Protocol,

802.1p - Class of Service,

802.1Q - VLAN Tagging

802.1w - Rapid Spanning Tree Protocol,

802.1X - Authentication

802.1ad - VLAN QinQ

802.1AB - LLDP

802.1s - MSTP

PWR1: 45~57VDC

Each POE port output ranged of 44-57V ,600mA, it also can be designed to provide 30W power to loads. V+ matched with data cable 1/2, and V- matched with data cable 3/6 gross power=POE ports*POE each power

Environment

Operating temperature -40 ~ 75oC (-40~167oF )

Storage temperature -40 ~ 85oC (-40~185oF)

Operating humidity 5% to 95%,No condensation

Mechanical

Dimensions(W x D x H) 68 mm(W) x 106 mm(D) x 146 mm(H)(DIN-rail)

Casing IP-40 protection

Certification

Shock IEC 60068-2-27

Free Fall IEC 60068-2-32

Vibration IEC 60068-2-6

Warranty 5 years

BCDVideo BCD-RGD-804P-MT User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual