B+B SmartWorx iMediaChassis/20, iMediaChassis/6, iMediaChassis/3 User Manual

Download

iMediaChassis Series

iMediaChassis 3, 6 and 20 slot

USER MANUAL

IMediaChassis Series

Advantech B+B SmartWorx - Americas

707 Dayton Road

Ottawa, IL 61350 USA

Phone (815) 433-5100

Fax (815) 433-5105

Advantech B+B SmartWorx - European Headquarters

Westlink Commercial Park

Oranmore, Co. Galway, Ireland

Phone +353 91-792444

Fax +353 91-792445

www.advantech-bb.com

B+B SMARTWOR X TECHNICAL SU PPORT

USA/Canada: 1 (800) 346-3119 (Ottawa IL USA location)

Monday - Friday, 7:00 a.m. to 7:00 p.m. CST

Europe: +353 91 792444 (Ireland location)

Monday - Friday, 8 a.m. to 5:00 p.m . GMT

Email: support@advantech-bb.com Web: www.advantech-bb.com

IMediaChassis Series

CONTENTS

B+B SMARTWORX TECHNICAL SUPPORT…………………………… i List of Figures………………………………………………………………. iv FCC RADIO FREQUENCY INTERFERENCE STATEMENT…………. v

Class A ...................................................................................................... vi

Class B ...................................................................................................... vi

WARRANTY………………………………………………………………. viii ABOUT THE IMEDIACHASSIS/20……………………………………….. 1 HARDWARE FEATURES…………………………………………………. 1

Alarm Reset, Last Gasp and Temperature Gauge ......................... 1

Alarm Reset Button ......................................................................... 2

Last Gasp Alarm ............................................................................. 2

Temperature Gauge ........................................................................ 3

SNMP Write Lock ............................................................................ 3

SNMP Management Module LEDs ................................................. 4

Installing the iMediaChassis/20.............................................................. 4

DC Power Supply Module Wiring Instructions ................................ 5

Installing SNMP Management and Application (iMcV-) Modules ..... 6

Replacing Power Supply Modules ......................................................... 7

User Replaceable Power Supplies ................................................. 7

Dual AC, Part Number 850-10960-2AC.......................................... 7

Dual DC, Part Number 850-10960-2DC ......................................... 8

Dual AC, Part Number 605-10144-2AC.......................................... 9

Dual DC, Part Number 605-10145-2DC ......................................... 9

iMediaChassis/2 0 Specif ic a tions ………………………………………… 10 About the iMediaChassis/6………………………………………………. 11 Hardware Features 12

Alarm Reset, Last Gasp, and Temperature Gauge ...................... 12

Alarm Reset Button ....................................................................... 12

Last Gasp Alarm ........................................................................... 12

IMediaChassis Series

iii

Temperature Gauge ...................................................................... 12

SNMP Write Lock .......................................................................... 13

Installing the iMedi aChas s is /6 .............................................................. 13

DC Power Wiring, Replacing Power Supply Modules and Fans ..... 15

DC Power Supply Wiring Instruction

s ................................................. 15

User-Replaceab le Power Supp ly Modul es ................................... 15

Fans .............................................................................................. 16

Installing Management and Application (iMcV-)Modules ................. 16

Installing Applications Modules ..................................................... 16

iMediaChassis/6 Specifications ............................................................ 17

About the iMediaChassis/3……………………………………………… 18 Hardware Features……………………………………………………….. 18

Alarm Reset, Last Gasp, and Temperature Gauge ...................... 18

Alarm Reset Button ....................................................................... 18

Last Gasp Alarm ........................................................................... 19

Temperature Gauge ...................................................................... 19

Installing the iMediaChassis/3 .............................................................. 19

DC Power Wiring, Replacing Power Supply Modules and Fans ..... 20

DC Power Supply Module Wiring Instructions .............................. 20

Power Supply Modules ................................................................. 21

Fans .............................................................................................. 21

Installing Management and Application Modules .................................... 21

Installing Applications Modules ..................................................... 22

SNMP Write Lock .......................................................................... 22

iMediaChassis/3 Specifications………………………………………….. 23 Hardware Feature Matrix……………………………………………….. 24 ELECTROSTATIC DISCHARGE PRECAUTIONS……………………. 25 CERTIFICATIONS……………………………………………………….. 26

IMediaChassis Series

LIST OF FIGURES

Figure 1: iMediaChass is/20, all m odels ........................................................... 2

Figure 2: SNMP Write Lock Switch ....................................................................... 3

Figure 3: DC Wiring Scheme ................................................................................. 5

Figure 4: 850-10960-2AC PS ................................................................................. 7

Figure 5: 850-10960-2DC PS ................................................................................ 8

Figure 6: 605-10144-2AC PS ................................................................................. 9

Figure 7: 605-10144-2DC PS ................................................................................ 9

Figure 8: iMediaChassis/6 PS ............................................................................. 11

Figure 9: DC Wiring Scheme for iMediaChassis/6 .............................................. 15

Figure 10: SNMP Module location for iMediaChassis/6 .................................... 16

Figure 11: DC Wiring Scheme iMediaChassis/3 ................................................. 21

Figure 12: SNMP Module Slot on iMediaChassis/3 ............................................ 22

IMediaChassis Series

FCC RADIO FREQ UENCY INTERFER ENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class x computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which the user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authorit y to operat e the equ ipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class A limits for radio noise emission from digi tal apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

IMediaChassis Series

Class A

This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which the user will be required to correct the interference at his/her own expense.

Any changes or modifications not expressly approved by the manufacturer coul d void the user’s authority to operate the equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

Class B

This equipment has been tested and found to comply with the limi ts f or a Cl a ss B computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which the user will be required to correct the interference at his/her own expense.

Any changes or modifications not expressly approved by the manufacturer coul d void the user’s authority to operate the equipment.

IMediaChassis Series

vii

Product

Description

Version

FCC

Class A

FCC

Class B

iMediaChassis/20

Dual AC



Dual DC



iMediaChassis/6



Dual AC



Dual DC



iMediaChassis/3



2AC



2DC



ACDC



IMediaChassis Series

viii

WARRANTY

Effective for products of B+B SmartWorx shipped on or after May 1, 2013, B+B SmartWorx warrants that each such product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicabl e solel y to the original user and is not transferable.

This warranty is expressly conditioned upon proper storage, installation, c onnect i on, operation and maintenance of products in accordance with their written specifications.

Pursuant to the warranty, within the warranty period, B+B SmartWorx, at its option will:

1. Replace the product with a functional equivalent;

2. Repair the product; or

3. Provide a partial refund of purchase price based on a depreciated value. Products of other manufacturers sold by B+B SmartWorx are not subject to any warranty or

indemnity offered by B+B SmartWo rx, but may be subject to the warranties of the other manufacturers.

Notwithstanding the foregoing, under no circumstances shall B+B SmartWorx have any warranty obligations or any other liability for: (i) any defects resul ting from wear and tear, accident, improper use by the buyer or use by any third party except in accordance with the written instructions or advice of the B+B SmartWorx or the manufacturer of the products, including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have been adjusted, modified or repaired by any party other than B+B SmartWorx or (iii) any descriptions, illustrations, figures as to performance, drawings and particulars of weights and dimensions contained in the B+B SmartWorx’ catalog s, pr i c e li s t s, m arketing materials or elsewhere since they are merel y int ended to represent a general idea of t he pr o ducts and do not form part of this price qu ote and do not consti tu t e a warrant y of any kind, whether express or implied, as to any of the B+B SmartWorx’ products.

THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET FORTH ABOVE IS B+B SMARTWORX’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED, INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B+B SMARTWORX BE LIABLE FOR LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF B+B SMARTWORX WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.

IMediaChassis Series

ABOUT THE IMEDIACHASSIS/20

The iMediaChassis series is a modular chassis platform designed for use with B&B Electronics’ Simple Network Management Protocol (SNMP) manageable series of modules. The iMediaChassis/20 is a 3U high, rack mountable chassis that features 20 slots for installing application series modules plus an additional slot for installing an SNMP Management Module. Power supply modules are user-replaceab le and hot-swappable.

The iMediaChassis/20 line offers models available in dual AC, dual DC and ACDC versions.

It offers features such as end-user replaceable power supply modules, temperature monitoring, Last Gasp and an Alarm Reset Button.

HARDWARE FEATURES

ALARM RESET, LAST GASP AND TEMPERATURE GAUGE

The iMediaChassis/20 series supports power supply modules, so that worn parts can be replaced without having to send an entire unit in for repair.

IMediaChassis Series

User-Replaceable

Power Supply Modules

Figure 1: iMediaChassis/20, all models

ALARM RESET BUTTON

When one power supply module malfunctions, an audible alarm sounds indicating the loss of the power module. The alarm can be silenced by pressing the Alarm Reset Button, located next to the power connector on the power supply module. If this occurs, remove and replace the power supply module immediately. (LEDs on the Management Module and the power supply module itself also indicate power supply module failures.)

LAST GASP ALARM

The iMediaChassis series includes the Last Gasp trap feature, “Remote Chassis Down”, which sends a Trap when the following occurs:

• Both power supply modules malfunction.

• Both power supply modules are powered down.

• When the AC line fails.

IMediaChassis Series

TEMPER ATURE G AUGE

The iMediaChassis/20 includes a temperature monitoring gauge with a heat sensor on the backplane of the chassis. Users define a threshold for chassis temperature via SNMP. If the chassis’ temperature rises above the specified level, the SNMP agent sends a trap (configured in iView²) to the administrator. There is also an LED indicator on the SNMP Management Module for chassis temperature.

SNMP W RITE LOCK

There is an SNMP Write Lock switch located below slot #3 on the front of the iMediaChassis/20. The SNMP Write Lock switch prevents a new management board from re-con fig ur in g the appl ic atio n module settings (e.g., the status of features such as LinkLoss, FiberAlert, Force mode, etc.) made via SNMP on any previous Management Modules.

Figure 2: SNMP Write Lock Switch

NOTE

Leave this switch in the

NORMAL

position during day-to-day operation; the

LOCKED

position should only be used when changing the SNMP management board.

The SNMP Management Module can be removed and replaced as necessary. Refer to the SNMP Management Module manual for complete instructions about configuration and oper atio n. If an SNMP Management Module is installed, refer to the LED panel below for indicators of Link, Temperature, Power supply modules and other functions.

IMediaChassis Series

SNMP M ANAGEMEN T MODUL E LEDS

The SNMP Management Module features several LEDs. The LED functions are:

LNK/ACT

FDX/COL

TEMP

FAN A / FAN B

Glows green when a link is established on port. Blinks green when data activity occurs.

Glows yellow when port is in Full-duplex mode. Blinks yellow when port is operating in Half-duplex mode and collisions occur.

Glows yellow when temperature of unit surpasses a user-defined level.

Glows yellow when one module malfunctions. Glows yellow when a fan malfunctions.

Installing the iMediaChassis/20

Install the chassis first before installing any modules into an iMediaChassis. When installing the chassis, be sure to observe the following precautions to prevent electrica l or mechanical damage:

1. Protect the chassis from exposure to sunl ight and electrical or magnetic

fields.

2. Ensure that the equipment rack remains stable, even with the addition of the

chassis and its associated cabling.

To install 20 -slot Rackmount chassis:

1. Have four #10 screws and four clip nuts available (hardware may vary

depending on rack type). The rest of the hardware is supplied with the unit.

2. Locate a suitable location in the rack for installation and secure the clip-nuts

onto the mounting rails. Use screws to attach the chassis to the rack.

3. Plug the chassis into a reliable, filtered power source.

4. Elevated Operating Ambient - If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may

IMediaChassis Series

be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the B+B SmartWorx.

5. Reduced Air Flow - Installation of the equipment in a rack should be such

that the amount of air flow required for safe operation of the equipment is not compromised.

6. Mechanical Loading - Mounting of the equipment in the rack should be such

that a hazardous condition is not achieved due to uneven mechanical loading.

7. Circuit Overloading - Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring.

8. Reliable Grounding - Reliable grounding of rack-mounted equipment should

be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

9. All AC and DC versions are intended for use in a Restricted Access Location

(RAL).

DC POW ER SUPPLY MODU LE WIRING IN STRUCTIONS

The following diagram shows the wiring configuration for a -48 VDC power supply module for the iMediaChassis/20-2DC and iMediaChassis/20-ACDC.

Figure 3: DC Wiring Scheme

NOTE

The chassis is protected against incorrect wiring configurations. When wired incorrectly, the chassis will not function, but no damage will occur.

IMediaChassis Series

Installing SNMP Manageme nt and Application (iMcV-) Modules

To install a module:

1. Remove the blank bracket (if present) covering the slot where the module

will be installed. B+B SmartWorx recommends installing blank brackets in unused module slots.

2. Slide the module into the chassis using the card guides.

3. Secure the module to the chassis by tightening the captive screw. (Refer to

the documentation shipped with the module for configuration information.)

4. When installing modules observe ESD precautions, refer to the Electrostatic

Discharge Precautions section.

In order to manage an iMediaChassis series, the SNMP Management Module needs to be installed in the appropriate slot of the chassis.

Install the iMediaChassis/20 SNMP Management Module into the first slot of the chassis.

NOTE

This slot is ONLY for the Management Module; do not install Application Modules such as media conversion and mode conversion modules in this slot.

IMediaChassis Series

REPLACING POW ER SUPPLY MO DULES

USER REPLACEABLE POWER SUPPLIE S

The iMediaChassis power supply modules are redundant *, failed power supply modules should promptly be replaced to maintain network integrity and prevent data loss.

To replace a power supply module:

1. Disconnect the power source from the power supply module.

2. Remove the screws of the retainer plate (on some AC modules).

3. Move the Power Supply Release switch toward the right or unscrew captive

release screw.

4. Before grasping the power supply module by the silver handle, press the

release screw and then slide out of the chassis (Power supply modules are hot-swappable).

5. Install new power supply module. If module is equipped with an ON/OFF

switch install the module with the switch in the OFF position.

DUAL AC, PART NUMBER 850-10960-2AC

Figure 4: 850-10960-2AC PS

IMediaChassis Series

DUAL DC, PA RT NUMBER 850-10960-2DC

Figure 5: 850-10960-2DC PS

Both the 850-10960-2AC and 850-10960-2DC were put on End-of-Life “EOL” in June 2015; support is still available for existing chassis deployed. Power supplies are limited to a six year warranty.

IMediaChassis Series

DUAL AC, PART NUMBER 605-10144-2AC

Figure 6: 605-10144-2AC PS

DUAL DC, PA RT NUMBER 605-10145-2DC

Figure 7: 605-10144-2DC PS

IMediaChassis Series

iMediaChassis/2 0 Specif i cat ion s Input Specifications

Dua l AC

100 to 240V AC, 50/60Hz, 3.5/1.5A

Dual DC

-48V DC, 5A

ACDC

100 to 240V AC, 50/60HZ, 2A

-48V DC, 4.4A

Operating Temperature 0° C to 50° C (32° F to 122° F)

Storage Temperature Dual AC & ACDC

-20° C to 80° C (-4° F to 176° F)

Dual DC

-20° C to 60° C (-4° F to 140° F)

Humidity

20 to 90% (non-condensing at 40° C)

Shipping Weight

11.3 kg (25 lbs)

Dimensions

13.21 x 48.26 x 35.0 5cm (5.2 x 19.0 x 13.8 inches)

IMediaChassis Series

ABOUT THE IM EDIACHASSIS/6

The iMediaChassis series is a modular chassis platform designed for use with B+B SmartWorx Simple Network Management Protocol (SNMP) manageable series of modules. The iMediaChassis/6 is 1U high, can be installed on a rack mount shelf, and supports optional redundant power supply modules, as well as an SNMP Management Module.

The iMediaChassis/6 series offers a line of models includi ng single AC, single DC, dual AC and dual DC. It offers features such as end-user replaceable power supply modules, temperature monitoring, Last Gasp and an Alarm Reset Button.

Figure 8:iMediaChassis/6 PS

IMediaChassis Series

HARDWARE FE ATURES

ALARM RESET, LAST GASP, AND T EMPERAT URE GAUGE

The iMediaChassis series supports modular power supply modules, so that worn parts can be replaced without having to send an entire unit in for repair. Keeping fans functional ensures that the modules will operate within their temperature specifications.

ALARM RESET BUTTON

When one power supply module malfunctions, an audible alarm sounds indicating the loss of the power supply module. The alarm can be silenced by pressing the Alarm Reset Button, located next to the power connector on the power supply module. If this occurs, remove and replace the power supply module immediately. (LEDs on the Management Module and the power supply itself also indicate power supply failures.) After stopping the al arm, remove the power supply and replace the power supply module.

LAST G ASP ALARM

The iMediaChassis series includes the Last Gasp trap feature, “Remote Chassis Down”, which sends a Trap when the following occurs:

• Both power supply modules malfunction

• Both power supply modules are powered down

• When the AC line fails

TEMPERATURE GAUGE

The iMediaChassis/6 includes a temperature monitoring gauge with a heat sensor on the backplane of the chassis. Users define a threshold for chassis temperature via SNMP. If the chassis’ temperature rises above the specified level, the SNMP agent sends a trap (configured in iView²) to the administrator. There is also an LED indicator on the SNMP Management Module for chassis temperature.

IMediaChassis Series

SNMP W RITE LOCK

There is an SNMP Write Lock switch located above the SNMP module sl ot on the front of the iMediaChassis/6. The SNMP Write Lock switch prevents a new management board from re-configuring the application module settings (e.g., the status of features such as LinkLoss, FiberAlert, Force mode, etc.) made via SNMP on any previous Management Modules.

NOTE

Leave this switch in the

NORMAL

position during day-to-day operation; the

LOCKED

position should only be used when changing the SNMP management board.

Please refer to page 4 for SNMP LEDs.

Installing the iMediaChassis/6

Install the chassis first before installing any modules into an iMediaChassis. When installing the chassis, be sure to observe the following precautions to

prevent electrical or mechanical damage:

1. Protect the chassis from exposure to sunlight and electrical or magnetic

fields.

2. Ensure that the equipment rack remains stable, even with the addition of the

chassis and its associated cabling.

To install a 6-slot Rackmount chassis:

1. Have four #10 screws and four clip nuts available (hardware may vary

depending on rack type). The rest of the hardware is supplied with the unit.

2. Locate a suitable location in the rack for installation and secure the clip-nuts

onto the mounting rails. Use screws to attach the chassis to the rack.

3. Plug the chassis into a reliable, filtered power source.

IMediaChassis Series

4. Elevated Operating Ambient - If installed in a closed or multi-unit

rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the B+B SmartWorx.

5. Reduced Air Flow - Installation of the equipment in a rack should be

such that the amount of air flow required for safe operation of the equipment is not compromised.

6. Mechanical Loading - Mounting of the equipment in the rack should

be such that a hazardous condition is not achieved due to uneven mechanical loading.

7. Circuit Overloading - Consideration should be given to the

connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring.

8. Reliable Grounding - Reliable grounding of Rackmounted equipment

should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

9. All AC and DC versions are intended for use in a Restricted Access Location

(RAL).

IMediaChassis Series

DC POW ER W IRING , R EPLA CING POWER SU PPLY MODULES AND FAN S

DC POWER SUPPLY WIRING INSTRUCTI ON

The following diagram shows the wiring configurations for -48 VDC power supply modules for the i MediaChassis/6.

Figure 9: DC Wiring Scheme for iMediaChassis/6

USER-REPLACEABLE POWER SUPPLY MODUL ES

The iMediaChassis/6 ships from B+B SmartWorx with one or two power supply modules installed depending on the model. Chassis ordered with one power supply come with a filler tray installed in the second slot.

To install a second power supply:

1. Remove the filler tray.

2. Slide the power supply module into the chassis and click into place.

3. Attach power cord.

To remove a power supply mod ule:

1. Disconnect the power source from the power supply.

2. Move the Power Supply Release switch toward the right and hold while

grasping the power supply module by the si lver handle.

3. Slide out of the chassis. (Power supply modules are hot-swappable.)

Install new power supply module.

IMediaChassis Series

FANS

Users can define a threshold for fan operation via SNMP (when installed in a managed environment). If a fan’s speed falls below the specified level, SNMP sends a Trap (configured in iView²) to the administrator. There are al so two LED indicators on the SNMP Management Module for fan fai lure.

SNMP Management Modules include two twisted pair ports, one for management and one reserved for future use. The Management Module also features a DB9 serial port, and supports SNMP V1/V2c.

Installing Management and Application (iMcV-) Modules

INSTAL LING APPLIC ATIONS MODULES

To install a module:

1. Remove the blank bracket (if present) covering the slot where the module

will be installed. B+B SmartWorx recommends installing blank brackets in unused module slots.

2. Slide the module into the chassis using the card guides.

3. Secure the module to the chassis by tightening the captive screw. (Refer to

the documentation shipped with the module for configuration information.)

4. When installing modules observe ESD precautions, refer to the Electrostatic

Discharge Precautions section.

In order to manage an iMediaChassis series, the SNMP Management Module needs to be installed in the appropriate slot of the chassis.

Install the iMediaChassis/6 slot into the first slot on the far left of the chassis.

NOTE

This slot is ONLY for the Management Module; do not install Application Modules such as media conversion and mode conversion modules into this slot.

Figure 10: SNMP Module location for iMediaChassis/6

IMediaChassis Series

IMEDIACHASSIS/6 SPECIFICATIONS

Input Specifications

100 to 240V AC, 50/60Hz, 1A

-48V DC, 2A

Operating Temperature:

-25° C to 50° C (-130° F - 122° F)

-40° C to 100° C (-40° F - 212° F)

Storage Temperature:

-40° C to 85° C (-40° F - 185° F)

-55° C to 125° C (-67° F - 257° F)

Humidity

5 - 95% (non-condensing); 0-10,000 ft. altitude

Shipping Weight

13 lbs (5.90 kg)

Dimensions

4.45 x 44.07 x 27.05cm (1.75 x 17.35 x 10.65 inches)

IMediaChassis Series

ABOUT THE IM EDIACHASSIS/3

The iMediaChassis series is a modular chassis platform designed for use with B+B SmartWorx’ Simple Network Management Protocol (SNMP) manageable series of modules. The iMediaChassis/3 is a 1U high, can be mounted on a rack shelf, capable of offering redundant power supply modules, and supports an SNMP Management Module.

The iMediaChassis/3 series offers a line of models including single AC, single DC, dual AC, dual DC and ACDC version. All contain internal fixed power supply modules that are not end-user replaceable. It offers features such as redundant power supply modules, temperature monitoring, Last Gasp and an Alarm Reset Button.

HARDWARE FEATURES

ALARM RESET, LAST GASP, AND T EMPERAT URE GAUGE

The iMediaChassis/3 ships with one or two AC or DC power supply modules, depending on the model. Fans are included in all models.

ALARM RESET BUTTON

When one power supply module malfunctions, an audible alarm sounds indicating the loss of the power supply. The alarm can be silenced by pressing the Alarm Reset Button, located next to the power connector on the power supply module. If this occurs the unit needs to be returned to IMC for repair.

IMediaChassis Series

LAST GASP ALARM

The iMediaChassis series includes the Last Gasp trap feature, “Remote Chassis Down”, which sends a Trap when the following occurs:

• Both power supply modules malfunction

• Both power supply modules are powered down

• When the AC line fails

TEMPER ATURE G AUGE

The iMediaChassis/3 includes a temperature monitoring gauge with a heat sensor on the SNMP Management Module. Users define a threshold for chassis temperature via SNMP. If the chassis’ temperature rises above the specified level, the SNMP agent sends a trap (configured in iView²) to the ad m inis trator. There is also an LED indicator on the SNMP Management Module for chassis temperature.

Installing the iMediaChassis/3

Install the chassis first before installing any modules into an iMediaChassis. When installing the chassis, be sure to observe the following precautions to

prevent electrical or mechanical damage:

1. Stay within the chassis’ power rating to prevent overload of supply circuits or

damage to any overcurrent protection and supply wiring.

2. Maintain reliable ground, especially when connecting to a power strip instead

of directly to a branch circuit.

3. Protect the chassis from exposure to sunl ight and electrical or magnetic

fields.

4. Ensure that the equipment rack remains stable, even with the addition of the

chassis and its associated cabling.

Use the iMediaChassis/3 as a table-top chassis, mount on a Rackmount shelf. To install the 3-slot Rackmount in the chassis:

1. Install the iMediaChas sis /3 by plac in g it on a flat surface.

2. Make sure to leave adequate space on the sides of the unit to accommodate

cooling.

3. If mounting on a Rackmount shelf, align holes of the chassis to the shelf and

secure with screws.

IMediaChassis Series

The Rackmount shelf is sold separately. To purchase the Rackmount shelf, (part number #895-39949, visit the B+B SmartWorx’ Product Accessories page.

4. Attach the cables between the chassis and the device that will be

interconnected, and then plug the unit into a reliable, filtered power source.

5. If mounting the chassis on a wall, place two #10 pan head screws (not

supplied) on the wall according to the distance of the holes on the chassis, and then hang the unit on the screws.

6. All versions are intended for use in a Restricted Access Location (RAL).

7. A readily accessible disconnect device shall be incorporated in the building

installation wiring.

8. A suitable listed circuit breaker shall be provided in the building installation

as the unit’s disconnect device. The branch circuit rating (i.e. minimum 15A listed circuit breaker, etc.).

DC POWER WIRING, R EPLACING POW ER SUPPL Y MODULES AND FAN S

DC POWER SUPPLY MODU LE WIRING INSTRUCT IONS

The following image shows the wiring configuration for a 48 VDC power supply in a negative ground system application. For positive ground system applications remove the chassis ground shorting jumper and connect it between the positive terminal and the chassis ground terminal. Alternatively, the chassis grounding jumper can be eliminated and the chassis ground connected at the power source.

The ground terminal and the negative

terminal are not connected inside the iMediaChassis/3.

IMediaChassis Series

DC Power Supply

Negative ground system configuration (default position)

Figure 11: DC Wiring Scheme iMediaChassis/3

NOTE

Incorrect wiring will result in chassis malfunction.

The iMed iaC hassis/3 is compliant with Isolated Grounding P la ne practices. The POSITIVE and NEGAT I V E terminals are isolated from cha ssis ground and must

have a groun d reference at the power-s ourcing equipment.

POW ER SUPPLY MO DULES

Power supply modules in all models of the iMediaChassis/3 are fixed, and not end-user replaceab le.

FANS

The iMediaChassis/3 includes temperature-t r igg ered fans . When the temperature inside the chassis reaches 45° C, the two fans activate to cool the chassis. Fans are not end-user replaceable.

Installing Management and Application Modules

SNMP Management Modules include two twisted pair ports, one for management and one reserved for future use. The Management Module also features a DB-9 serial port, and supports SNMP V1/V2c.

IMediaChassis Series

INSTAL LING APPLIC ATIONS MODULES

To install a module:

1. Remove the blank bracket (if present) covering the slot where the module

will be installed. B+B SmartWorx recommends installing blank brackets in unused module slots.

2. Slid e the module into the chassis usi ng the card guides.

3. Secure the module to the chassis by tightening the captive screw. (Refer to

the documentation shipped with the module for configuration information.)

In order to manage an iMediaChassis series, the SNMP Management Module needs to be installed in the appropriate slot of the chassis.

Install the iMediaChassis/3 slot SNMP Management Module into the bottom left slot.

NOTE

This slot is ONLY for the Management Module; do not install Application Modules such as media conversion and mode conversion modules in this slot.

Figure 12: SNMP Module Slot on iMediaChassis/3

SNMP W RITE LOCK

The SNMP Write Lock switch is located on the back of the iMediaChassi s/3. The SNMP Write Lock switch prevents a new management board from re-configuring the application module settings (e.g., the status of features such as LinkLoss, FiberAlert, Force mode, etc.) made via SNMP on any previous Management Modules.

IMediaChassis Series

NOTE

Leave this switch in the

NORMAL

position during day-to-day operation; the

LOCKED

positi on should only be used when changing the SNMP management board.

The SNMP Management Module can be removed and replaced as necessary. Refer to the SNMP Management Module manual for complete instructions about how to configure and operate. If an SNMP Management Module is installed, refer to the LED panel below for indicators of Link, Temperature, Power Supply modules and other functions.

Please refer to page 4 for SNMP LEDs.

IMEDIACHASSIS/3 SPECIFICATIONS

Input Specifications

100 to 240V AC, 50/60Hz, 0.75A

35V DC to 75V DC Ma x, 1.6A

Operating Temperature

0° C to 50° C (32° F to 122° F)

-40° C to 50° C (-67° F to 122° F)

Storage Temperature

AC -40° C to 85° C (-40° F to 185° F)

DC -55° C to 125° C (-40° F to 212° F)

IMediaChassis Series

Humidity: 5 to 95% (non-condensing); 0 to 10,000 ft. altitude

Shipping Weight: 5 lbs (2.3 kg)

Dimensions: 4.4 x 19.0 x 22.0 cm (1.73H 7.50W 8.74D inches)

Hardware Feature Matrix

Power Supply iMediaChassis/3

Versions AC, 2AC, DC, 2DC*, ACDC

Type Fixed End user replaceable No LEDs Yes Redundant upgrade on single slot

chassis

*Trap ca n be set for exceed ing a temperature val ue

WARNING

Disconnect all power supplies before servicing.

IMediaChassis Series

ELECTROST ATIC DISCHARGE PRECAUTIONS

Electrostatic discharge (ESD) can cause damage to any product, add-in modules or stand-alone units, containing electronic components. Always observe the following precautions when installing or handling these kinds of products:

Do not remove unit from its protective packaging until ready to install. Wear an ESD wrist grounding strap before handling any module or

component. If the wrist strap is not available, maintain grounded contact with the system unit throughout any procedure requiring ESD protection.

Hold the units by the edges; do not touch the electronic components or gold connectors.

After removal, always place the boards on a grounded, static-free surface, ESD pad or in a proper ESD bag. Do not slide the modules or stand-alone units over any surface.

WARNING! Integrated circuits and fiber optic components are extremely susceptible to electrostatic discharge damage. Do not handle these components directly unless you are a qualified service technici an and use t ools an d techniques that conform to accepted industry practices.

UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment.

CE:

The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC) and the Council Directive on Electrical Equipment Designed for use within Certain Voltage Limits (2006/95/EC). Certified to Safety of Information Technology Equipment, Including Electrical Business Equipment. For further details, contact B&B Electronics.

IMediaChassis Series

CERTIFICATIONS

CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC). For further details, contact B+B SmartWorx.

European Directive 2002/96/EC (WEEE) requires that any equipment that bears this symbol on product or packaging must not be disposed of with unsorted municipal waste. This symbol indicates that the equipment should be disposed of separately from regular household waste. It is the consumer’s responsibility to dispose of this and all equipment so marked through designated collection facilities appointed by government or local authorities. Following these steps through proper disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about proper disposal, please contact local authorities, waste disposal services, or the point of purchase for this equipment.

© 2017 B+B SmartWorx. All rights reserved. The information in this document is subject to change without notice. B+B SmartWorx assumes no responsibility for any errors that may appear in this document . iMediaChassis is a trademark of B+B SmartWorx. Other brands or product names may be trademarks and are the property of their respective companies.

Document Number: iMediaChassisSeries_3-6-20_50-10954-01-A2_1417m

Class 1 Laser product, Luokan 1 Laserlaite,

Laser Klasse 1, Appareil A’Laser de Classe 1

B+B SmartWorx iMediaChassis/20, iMediaChassis/6, iMediaChassis/3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual