B+B SmartWorx IE-MiniFiberLinX-II Quick Start Manual

1-888-948-2248 | Europe: [phone]

advantech-bb.com

707 Dayton Road | PO Box 1040 | Ottawa, IL 61350

Phone: [phone] | Fax: [phone]

www.adva ntech- bb.com | E-mail: suppo rt@adva ntech- bb.com

Fast and easy on the web:

www.advantech-bb.com

QUICK START
GUIDE

Document N umber:

IE-MiniFiberLinX-II_Telco-LastGasp _56-85722-01_R2_ 3217qsg

Recommended Accessories

iView2 Network
Management Software

-Free download

Ethernet Cables

- Sold separately

Before you begin, be
sure you have the following:

IE-MiniFiberLinX-II Series

Compact Optical Demarcation Device

with Telco/LastGasp

+ IE-MiniFiberLinX-II
+ 100/240V AC input, 5V power adapter
Power Supply (included)
+ Console port mini-jack adapter (included)

Troubleshooting

6

SNMP Questions

To manage the product, assign an IP address and subnet

mask.

Which port have you assigned to use for management

(SNM P)?

Do you have SNMP ser vices from the WIN CD installed?

iView²

The IE-MiniFiberLinX-II is supported by the iView²
Webserver version.

Check Type of Cable Used

A Cat 5 Ethernet cable is required for the RJ -45 ports.

Make sure that the pins are not pulled out of the
connector’s casing, which will cause damage to the
device’s copper ports.

PI NG Te st

A PING test can be per formed to test connectivity of the

device - either on the copper port or the ber port.

To perform a PING test, Port 3 must be set to “enable” for

S N M P.

Resources

For optimal performance of the device, make sure to

download the latest version of software and rmware for

the device. These are available on the B+B SmartWorx
website.

For information about product specications, please refer to

the datasheet.

For information about warranty, please refer to the the

website.

Product Overview

Power Options

Connecting Fiber and Twisted
Pair Cables

1

3

4

IE MiniFiberLinX-II is a CPE device (Remote) and can be

connected to a Host device.

A Host device can be an iMcV-FiberLinX-II or a switch. (For

other types of installation, please see the manual.)

1. Connect the ber cable to the ber port.

FX LNK/ACT: Glows green when a link is established on

the ber port; blinks green when activity is detected on the
ber port.

2. Plug in the RJ- 45 cable to the Twisted Pair port.
TX LNK/ACT: Glows amber when a link is established on the

copper port; blinks amber when activity is detected on the

copper port.

Fiber XMT Fiber RCV

Ethernet PoE

(PD) Port

Fiber RCV

Power Adapter

Connector

Console / Craft por t

7-50V DC dual co nnector

for daisy chaining

Front

Back

1. A country-specic, high- reliability power adapter
(included). 100/240V AC input, 5V DC output.

2. IEEE 802.3af Power-over-Ethernet (Powered Device)

standard; draws power from PoE (Power Sourcing

Equipment).

3. 4-terminal DC power block.

5 to 24 VDC

Ground

(common)

12 to 48 VDC

Powering options include AC and DC power as well as
Power-over-Ethernet, functioning as a PD compliant with

802.3af. To use the DC terminal block, connect to any

one Positive and any one Negative terminal from a power
source.

Power Options - all Telco versions

2

It does not mat ter which terminal is refer enced (connected to) earth­ground. For examp le, when using a -48 VDC su pply in which the positive
rail is conne cted to earth ground, sim ply connect this side to a term inal
block “+” termi nal and the -48 VDC side to th e negative terminals.

This equipmen t is designed to permit the co nnection of the grounded
conductor of the DC supply circuit to the grounding conductor at the
equipment.

Twisted Pair LED

Link/Activity

Fiber LED

Link/Activity

XMT

RCV

Fiber Port

Conguration via Console

Session

1. Computer must be attached to the local LAN

connection via the copper port. The ber por t must
be connected to a ber link partner via the ber por t,

and on the same Subnet Mask.

2. Start iCong and scan for devices.

3. A new device will show IP Address 10.10.10.10 with
its name IE-MiniFiberLinX-II

4. Open Session by typing in the USER NAME and
USER PASSWORD. Defaults: admin/admin

5. Set the IP Address, Subnet Mask and Default
Gateway as required.

5

Conguration via iView²

(iCong)

The IEMini FiberLinX-II is a C PE device, and it is not recomm ended
to install it in p airs. It can be installe d as a Remote device and

connected to an iMcV-Fi berLinX- II congured as the Host device.

1. Set the computer / terminal for VT-100 emulation with
the following settings: 38.4K baud, 8 data bits, 1 stop

bit, no parity, no ow control.

2. Connect the RS-232 cable to the Console por t,
backside of the unit. Use the mini-jack adapter included
with the device.

3. Start the Serial session and press the Enter Key.

4. Set IP Address, Subnet Mask, Default Gateway and
SNMP Community String if direct SNMP / Telnet
management is required.

5. Set Mode and Ethernet Port Cong.

6. Set Password if serial port security is required
(optional).

7. Type “Reboot“ for changes to take effect.