B+B SmartWorx FOSTCDRi-PH-MT, FOSTCDRi-PH-MC, FOSTCDRi-PH-SC Quick Start Manuals

Recommended Accessories

Industrial Power Supply

Model# MDR-20-24

Document Number: 710-10863-00_r2_FOSTCDRI-PH-xx_2118qsg

1 [phone] | Europe: [phone]

www.advantech-bb.com

707 Dayton Road | PO Box 1040 | Ottawa, IL 61350

Phone: [phone] | Fax: [phone]

www.advantech-bb.com | E-mail: supp [e-mail]

Before you begin, be
sure you have the following:

Models FOSTCDRi-PH-MC,

FO STCDRi -PH - M T,

FOSTCDRi-PH-SC

3-Way Isolated Serial to Fiber Optic Converter

Fast and easy on the web:

www.advantech-bb.com

+ FOSTCDRi-PH-xx Fiber Optic Converter
+ Required but not included:
+ 10 to 48 VDC Power Supply

QUICK START
GUIDE

SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B,
C AND D HAZARDOUS LOCATIONS, OR NONHAZARDOUS
LOCATIONS ONLY.

CONVENANT À L’EMPLOI DANS LES SITES DANGEREUX
DE CLASSE I, DIVISION 2, GROUPES A , B, C ET D, OU
DANS LES SITES NON HASARDEUX SEULEMENT.

WARNING - EXPLOSION HA ZARD - SUBSTITUTION OF
ANY COMPONENT MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2.

ATTENTION - DANGER D’EXPLOSION - LA SUBSTITUTION
DE COMPOSANTS PEUT ENTR AÎNER UNE ADÉQUATION À
LA CLASSE I, DIVISION 2.

WARNING - EXPLOSION HA ZARD - DO NOT DISCONNECT
EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS
THE AREA IS KNOW TO BE FREE OF IGNITABLE
CONCENTRATIONS.

ATTENTION - DANGER D’EXPLOSION - LA SUBSTITUTION
DE COMPOSANTS PEUT ENTR AÎNER UNE ADÉQUATION À
LA CLASSE I, DIVISION 2.

Field wiring connections must be made using 105 °C minimum
copper supply wires.

Les connexions de câblage sur site doivent être réalisées en
utilisant des câbles d’alimentation en cuivre de 105 °C minimum.

To be installed in accordance with control drawing 8510r001.

Pour être installé conformément au dessin de contrôle 8510r001.

Multi-drop Ring

Model Number Connector Fiber Type Range Size

FOSTCDRi-PH-MT ST MM 2 kM 62.5/125 µm

FOSTCDRi-PH-MC SC MM 2 kM 62.5/125 µm

FOSTCDRi-PH-SC SC SM 15 kM 9/125 µm

Wavelength = 1310 nM

UL Class 1 Div. 2 Information

5

A) Power LED
B) Data LEDs
C) Fiber Optic ports
D) Serial TB
E) Ground Lug
F) DIP Switch
G) Serial Mode Switch
H) Power TB

Product Overview

Conguration DIP Switch

Fiber Optic Connections

Power & Ground Connection

Wiring Examples

1

4

2

3

Terminal RS-485 2-Wire RD422/485 4-Wire

A --- TDA (-)

B --- TDB (+)

C DATA A (-) RDA (-)

D DATA B (+) RDB (+)

E Ground Ground

Built-in Termination Resistor 5

Use the 120Ω Built-in Termination ON

Use External or No Termination OFF

Built-in Trasmit Bias Resistor 6

Use the External or No Bias Resistor ON

Use the 1.2KΩ Transmit Bias Resistor OFF

Built-in Receive Bias Resistor 7

Use the External or No Bias Resistor ON

Use the 1.2KΩ Receive Bias Resistor OFF

Fiber Optic Mode 8

Multi-drop Ring ON

Point-to-point OFF

1 2 3 4

RS-485 2-Wire

Half Duplex

ON ON ON ON

RS-485 4-Wire

Full Duplex

ON OFF OFF OFF

RS-422 Full

Duplex

OFF OFF OFF OFF

Terminal Signal Direction

A RD Output

B --- ---

C TD Input

D --- ---

E Ground ---

For an explanation of RS-485 termination requirements,
more documentation can be found at advantech-bb.com

+

2-Wire RS-485

RS-422/ 4-Wire RS-485

RS-232

Point-to-Point

Positions 5, 6, 7 are used for termination and biasing. Position 8 is

used for ber optic point-to-point or multi-drop ring.

Position 1 = ON for RS-485, OFF for RS-422. Positions 5, 6, 7

are used for termination and biasing. Position 8 is used for ber

optic point-to-point or multi-drop ring

DIP Switch positions 1 through
7 have no effect in RS-232
mode. Set position 8 to OFF

for ber optic point-to-point or

multi-drop ring.

Set DIP Switch position 8 to OFF on both converters. Connect
Fiber Optic TD to Fiber Optic RD and vice versa.

E = Ground

Note: Your FOSTCDRi-PH-x converter can only connect to
another FOSTCDRi-PH-x converter model at the other end of

the ber optic cable.

+