B+B SmartWorx BB-WSD2C31010, BB-WSD2M06010, BB-WSD2M31010, BB-WSD2C21150, BB-WSD2C06010 Quick Start Manual

Recommended Accessories

# BB-ZXTMT

Cable Gland/Conduit Kit

# BB-WCD-TM2M

Thermistor Cable

# BB-WSCAM12-6

M12 Cable Wiring Harness Cable

Document Number: 2009WSD200_r2_BB -WSD2x_WzzardInd_4718qsg

1 [phone] | Europe: [phone]

www.advantech-bb.com

707 Dayton Road | PO Box 1040 | Ottawa, IL 61350

Phone: [phone] | Fax: [phone]

www.advantech-bb.com | E-mail: [e-mail]

Before you begin, be
sure you have the following:

Fast and easy on the web:

www.advantech-bb.com

+ Wzzard Intelligent Edge Node
+ Wire Harness
+ (2) Lithium Thionyl Chloride AA Batteries
+ External Antenna
+ Anti-skid Disk

QUICK START
GUIDE

As nodes join the network, they will be added to the device
tree under the gateway MAC address.

When all nodes’ MAC addresses show in the tree, click the
checkbox next to each node.

Click the “Claim Nodes” button to prevent the nodes from
joining another open network.

Congure the Node

Mount the Node

5

6

Refer to the IWzzard Mesh Wireless Sensor user manual for

detailed conguration instructions.

Flange Mounting - Wzzard nodes may be mounted via
their mounting ears. (M5, #10)

Magnetic Mounting* - Wzzard nodes contain a powerful,
internal mounting magnet in the base of the node – pull
force 2.13 kg (4.7 lb) – convenient for temporary position-

ing and conguration of nodes.

Apply the anti-skid disk to the bottom of unit for extra grip.

* Note: UL Class1/Division2 rating does not apply (voided) when using magnetic mounting.

Putting the Node in Deep Sleep

7

When not using the node for some time, the node should be
put into deep sleep.

Press the Status/Sleep/Reset conguration button for 5

seconds until the Status LED turns off.
The node will retain all settings, including the associated

network if the node has been claimed. It will not reset the
device back to factory settings.

Restoring Node to Factory Default

8

To reset the node to factory defaults, press and hold the
Status/Sleep/Reset conguration button for 10 seconds until

the Status LED ashes quickly. This will:

1) Clear the sensor type information.

2) Clear the associated network information if the node has
been claimed.

3) Allow the node to search for a new network.

Models BB-WSD2C31010, BB-WSD2M31010,
BB-WSD2C21150, BB-WSD2C06010,
BB-WSD2M06010

for Industrial Applications

Intelligent Edge Node with SmartMesh IP

Wzzard™ Mesh Wireless Sensor

Review Network & Claim Nodes

4

Follow the SmartSwarm quck start guide to claim and
congure the gateway. With the gateway connected to
the internet, click on the “Wzzard Mesh” button.

(continued)

IP67

Enclosure

Product
Overview

Connect Your Sensor

Wake Up The Node

1

2

Check LEDs

3

After you wake the node, the Status LED will begin
to blink. This indicates that the node is attempting to
establish a network connection. The Status LED will come
on solid when a connection is made.

Note: The Status LED goes off after 10 seconds to conserve battery life. To

check status, use a short press of the Status/Sleep/Reset conguration button.

Status LED

Data

Slow Blink
(1 per sec.)

Attempting to establish connection
with SmartMesh IP network.

Fast Blink
(10 per sec.)

Firmware update in progress.

ON (solid) Unit is connected to wireless network.

MODEL

1

Brown2Red3 Pink4Yellow 5 Green6 Blue7 White8Gray

WSD2C31010 10-30VDC AIN1 AIN2 AIN3 DIN1 GND GND GND

WSD2C21150 10-30VDC AIN1 AIN2 DO1 DIN1 GND GND GND

WSD2C06010 10-30VDC DIN1 DIN2 DIN3 DIN4 DIN5 DIN6 GND

MODEL

1

White2 Brown3Green4Yellow 5Gray6 Pink7Blue8 Red

WSD2M31010 10-30VDC AIN1 AIN2 AIN3 DIN1 GND GND GND

WSD2M06010 10-30VDC DIN1 DIN2 DIN3 DIN4 DIN5 DIN6 GND

Wiring for Conduit Connector Nodes

– with Attached Wiring Harness

Wiring for M12 Connector Nodes*

– with M12 Accessory Cable (from B+B SmartWorx)

Wiring Chart Abbreviations:

10-30V = 10 -30V DC Power Input
AINx = Analog Input #x
DINx = Digital Input #x
GND = Ground Input

Wiring Chart Abbreviations:

10-30V = 10 -30V DC Power Input
AINx = Analog Input #x
DINx = Digital Input #x
DOx = Digit al Output #x
GND = Ground Input

* Note: UL Class1/Division2 rating is voided when using M12 model outdoors.

Status

LED

Antenna

Conduit or M12

Conguration

Button

Mounting Flanges

Case

Screws

Internal Magnet

(in the base)

Press and hold Status/Sleep/Reset conguration button

for 5 seconds until the Status LED comes on and begins
blinking.

Remove the four (4) black screws that hold the top of the
node in place. Connect your sensor.

Tip: It is a best practice that wiring is done prior to installing batteries or powering
up the device.

Note: UL C1/D2 rating is voided when using non UL-specied batteries.

Thread the included wire
harness through the conduit and
into the node. Plug it into the
circuit board inside the node.

Conduit Models: Analog & Digital

M12 Models*: Analog & Digital

– with Accessory Cable

You can use your own M12 cable or
order B+B SmartWorx accessory
cable #BB-WSCAM12-6.

1 White
2 Brown
3 Green
4 Yellow
5 Gray
6 Pink
7 Blue
8 Red

Terminal Block Connections

– Thermocouple & Thermistor

Thread the thermocouple and thermistor wires through the
conduit and attach them to the terminal block.

1 Brown
2 Red
3 Pink
4 Yellow
5 Green
6 Blue
7 White
8 Gray

Connect your sensor to the wires running from the node’s
conduit. Consult the following chart for wiring instructions.

Consult the following chart for wiring instructions.

M12 Accessory Cable Detail

– #BB-WSCAM12-6 (from B+B SmartWorx)

UL Class 1, Division 2
Notications and Warnings

Conduit Models Only

Model Numbers BB-WSD2C31010,
BB-WSD2C21150, BB-WSD2C06010:

10

Radio Equipment Directive

(RED) Statement

9

Hereby, B+B SmartWorx, Inc. declares that the
radio equipment type “Wzzard Wireless Mesh” is
in compliance with Directive 2014/53/EU.

The complete CE Declaration of Conformity is
available at:

https://support.advantech-bb.com/

Keywords, enter [model number]

Material Type, select Reference
Click Search

SUITABLE FOR USE IN CLASS I, DIVISION
2, GROUPS A, B, C AND D HAZARDOUS
LOCATIONS, OR NONHAZARDOUS LOCATIONS
ONLY.

CONVENANT À L’EMPLOI DANS LES SITES
DANGEREUX DE CLASSE I, DIVISION 2,
GROUPES A, B, C ET D, OU DANS LES SITES
NON HASARDEUX SEULEMENT

WARNING - EXPLOSION HAZARD - DO NOT
DISCONNECT EQUIPMENT WHILE THE CIRCUIT
IS LIVE OR UNLESS THE AREA IS KNOW TO BE
FREE OF IGNITABLE CONCENTRATIONS.

ATTENTION - RISQUE D’EXPLOSION - NE PAS
DÉCONNECTER L’ÉQUIPEMENT PENDANT
QUE LE CIRCUIT EST VIVANT OU À MOINS
QUE LA ZONE NE SAIT ÊTRE EXEMPTE DE
CONCENTRATIONS IGNIFIABLES.

For M12 Model Numbers

BB-WSD2M31010, BB-WSD2M06010:

THIS EQUIPMENT IS TO BE INSTALLED IN AN
ENCLOSURE SUITABLE FOR THE ENVIRONMENT
THAT IS ONLY ACCESSIBLE WITH THE USE OF A
TOOL.

CET ÉQUIPEMENT DOIT ÊTRE INSTALLÉ DANS
UNE ENCEINTE ADAPTÉE À L’ENVIRONNEMENT
QUI N’EST ACCESSIBLE QUE POUR L’UTILISATION
D’UN OUTIL.

The unit is to be connected to a Class 2 power source
via the terminal block.

L’unité doit être connectée à une source d’alimentation
de classe 2 via le bornier.

These products must use only the following batteries:
either Model XL-060F manufactured by XENO Energy
co LTD. Or Model ER14505 manufactured by EVE.
Please be advised of the following warning statement
regarding battery replacement.

Ces produits utilisent les batteries suivantes: soit le
modèle XL-060F fabriqué par XENO Energy co LTD.
Ou Modèle ER14505 fabriqué par EVE. Veuillez
prendre connaissance de l’avertissement suivant
concernant le remplacement de la batterie.

WARNING: Risk of Fire and Burns. Do Not Recharge,

Open, Crush, Heat Above 100˚C, Or Incinerate the

batteries. Batteries are not user replaceable, only

a qualied technician should replace the batteries.

Do not mix battery types, Do not mix old and new
batteries” or similar shall be included on the device or
accompanying documentation.

ATTENTION: Risque d’incendie et de brûlures. Ne
pas recharger, ouvrir, écraser, chauffer au-dessus de
100 °C, ou incinérer les batteries. Les piles ne sont
pas remplaçables par l’utilisateur, seul un technicien

qualié doit remplacer les piles. Ne pas mélanger

les types de piles. Ne pas mélanger les anciennes et
les nouvelles piles “ou similaires sur l’appareil ou la
documentation qui l’accompagne.

Torque value of 5 to 8 lb-in for screws used to secure
the cover to main housing must be included in
accompanying documentation.

Une valeur de couple de 5 à 8 lb-in pour les vis utilisées

pour xer le couvercle au boîtier principal doit être

incluse dans la documentation d’accompagnement.

WSD2C devices are suitable for use in a Type 3
(outdoor) environment. WSD2M devices (with M12
connector) are suitable or use in a Type 1 environment
and must be used in a suitable enclosure.

Les appareils WSD2C peuvent être utilisés dans un
environnement de type 3 (extérieur). Les appareils
WSD2M (avec connecteur M12) conviennent ou sont
utilisés dans un environnement de type 1 et doivent être

utilisés dans un boîtier approprié.

Operating temperature code for these products is T5.

Le code de température de fonctionnement pour ces
produits est T5.

See User Manual for information that is provided
separately.

Voir le manuel de l’utilisateur pour des informations
fournies séparément.

UL Class1/Division2 Applications

B+B SmartWorx Product Exceptions Summary

UL C1/D2 rating is voided when using M12 model
outdoors.

UL C1/D2 rating is voided if magnetic mounting is used
for permanent installation.

UL C1/D2 rating is voided when using non UL-specied

batteries. Do not mix old and new batteries.