B+B Sensors HM 1150 Instruction Manual

INSTRUCTION MANUAL

Technical changes reserved

Description

B+B 0141 0315-117 September 2010

01 / 12

Digital Quick-Response Thermometer HM 1150

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

02 / 12

Dear customer,

We thank you for having purchased the Digital Quick-Response Thermometer HM 1150 and we are very glad that you decided a product of B+B Thermo-Technik GmbH. We hope this product will fully satisfy you and will assist you effectively in your work.

This Device has been developed to be technically highly up-to date. This product has been designed in accordance with the regnant European and German national directives and rules. For a proper and effective usage of the product the customer shall observe the following Operating Instructions. In the case that against one’s expectations any trouble occurs which you can not resolve yourself, please contact our service centers or our authorized dealer. We will provide you rapid and competent help to minimize the risk of long time outfalls.

The following operating Instruction is an indispensable part of this Product. It contains important advices for the starting up and further use of the device.

Foreword

This Operation Manual is intended to serve as an aid in the proper setup, installation and operating of the B+B product.

All essential details of the equipment and all actions required on the part are clearly presented and explained. We thus ask that you read this manual carefully before proceeding to work with the equipment. Keep this manual available for ready reference in a convenient and conspicuous location near the equipment.

General Information

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

03 / 12

Content

Foreword 02

General Information 02

Symbols Employed 01

Warning Signs 04

Safety Instructions 05

Intendend Use 06

Disposal 06

1. Points to be observed during operation 07

2. Recalibration 08

3. Correctiontable: (typ. value) 09

4. Specication 10

5. Scope of Delivery 11

6. Optional Order Information 11

General Questions 12

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

04 / 12

Symbols Employed

Sign Meaning

Notice

Advice

It is necessary to read the following advices before using the product. The used symbols in the manual acts rst of all as eye catcher for security risks. The symbols do not replace the security advices. The text must be read completely.

Necessarily to observe

This symbol designates important advices and tips which are necessary for the success of a procedure. They have to be followed in order to get good results.

Warning Signs

Meaning

This symbol advises the user of danger for persons, material or environment. The text gives information that must be necessarily followed to avoid any risks

Caution against hot surfaces (BGV A8, GUV-V A8/W26) and hot liquids or substances

Caution against liquids and hot substances

Caution against dangerous explosive substances (BGV A8, GUV-V A8/W02)

Caution against moving maschines (W29) Caution against moving parts

Caution against electromagnetic elds (BGV A8, GUV-V A8/W12)

Caution against severe cold (BGV A8, GUV-V A8/W17)

Caution against dangerous high electrical voltage (BGV A8, GUV-V A8/W08)

Caution against dangerous explosive atmosphere (BGV A8, GUV-V A8/W21)

Electronic waste

Warning Signs

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

05 / 12

Safety Instructions

Für Schäden, die durch Nichtbeachten dieser Sicherheitshinweise und der Bedienungsanleitung verursacht werden, übernimmt die B+B Thermo-Technik GmbH keine Haftung.

This device has been designed and tested in accordance to the safety regulations for electronic devices. However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures and special safety advises given in this manual will be adhered to when using it.

Trouble-free operation and reliability of the device can only be guaranteed if it is not subjected to any other climatic conditions

than those stated under “Specication”.

If the device is transported from a cold to a warm environment condensation may result in a failure of the function. In such a case make sure the device temperature has adjusted to the ambient temperature before trying a new start-up.

If device is to be connected to other devices the circuitry has to be designed most carefully. Internal connection in third party devices (e.g. connection GND and earth) may result in not-permissible voltages impairing or destroying the device or another device connected.

Warning:

Just devices with mains input: If device is operated with a defective mains power supply (e.g. short circuit from mains voltage to output voltage) this may result in hazardous voltages at the device (e.g. at sensor socket)

If there is a risk whatsoever involved in running it, the device has to be switched off immediately and to be marked accordingly to avoid re-starting. Operator safety may be a risk if:

● there is visible damage to the device

● the device is not working as specied

● the device has been stored under unsuitable conditions for a longer time

In case of doubt, please return device to manufacturer for repair or maintenance.

Caution:

Do not use these product as safety or emergency stop devices, or in any other application where failure of the product could result in personal injury or material damage. Failure to comply with these instructions could result in death or serious injury and material damage.

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

06 / 12

Intendend Use

Disposal

The use of the unit in elds other than those indicated under “SAFETY INSTRUCTIONS” is not allowed for safety reasons.

This instruction manual does not at all substitute any additional instruction manual of connected accessoriy!

This unit has been marked in accordance with the European Device 2002/96/EC on waste electrical and electronic equipment (WEEE) At the end of its useful operating life, dispose of the unit as electrical scrap. Please ask either B+B Thermo-Technik GmbH or your specialist dealer for information on your local collection point. Within the scope of application if this Directive, B+B Thermo-Technik GmbH is responsible for proper disposal of this unit

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

07 / 12

1. Points to be observed during operation

a.) Make sure to apply correct operating voltage as low or damaged battery will lead to measuring inaccuracies. If „BAT“ is shown in the display or are the measurements obviously wrong the battery has been used up and needs to be replaced.

Please note:

If the battery voltage falls even lower the voltage may not be sufcient for „BAT“ to be displayed so that there will be no „BAT“ indication although the battery has been used up. We recommend to make it a rule to always check the battery if the values indicated seem to be completely out of range.

b.) Make sure to maintain device properly and to operate it in accordance with the specication listed (do not throw, knock etc.).

c.) Make sure that sensor and device are always subjected to the same temperature, i.e. try to avoid holding sensor plug in your hand for a longer periode of time as well as subjecting device to an additional heat source as this may result in measuring inaccuracies.

d.) Mains operation: When using a power supply unit please note that operating voltage has to be 10 to 12 V DC. Do not apply overvoltage!! Cheap 12V-power supply units often have excessive no-load voltage. We, therefore,

recommend using regulated voltage power supply units. Trouble-free operation is guaranteed by our power supply

GNG10/3000.

Prior to connecting the plug power supply unit with the mains supply make sure that the operating voltage stated at the power supply unit is identical to the mains voltage.

e.) The battery has to be taken out, when storing device above 50°C. It is recommended to take the battery out, when storing device for a longer period of time

f.) The length of the measuring sensor (GTF300) can be reduced as desired so that it will be fully operational again after sensor has been broken. To do so, please strip both wire ends for approx. 10mm and twist well. Measurements

are not possible as long as wire ends are exposed.

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

08 / 12

2. Recalibration

The measuring device will be calibrated before leaving our works. A recalibration is, therefore, not necessary. If you want to calibrate the device for an existing sensor, please proceed as follows: (calibrate 0°C before scale as otherwise correct adjustment cannot be guaranteed).

Normally sensor adjustment by means of 0° C potentiometer is sufcent. We do not recommend a scale compensation in order to maintain the specied accuracy of the device. If an accurate reference temperature is available, choose highest temperature

possible to calibrate the device.

Calibration point 0°C : Put ice cubes in a glass and pour cold water till ice cubes are almost covered. Put sensor into glass, wait approx. 15 minutes, then stirr water with a spoonhandle. Wait for stable value to be displayed, then turn zero point potentiometer (NP, Potentiometer next to sensor connection) by means of a screw driver till display shows „000“.

Calibration point scale : To set the pitch (Scale) a xed reference temperature is required (the higher the better). Subject sensor to this temperature and set respective display value according to corre tion table value (e.g. reference temperature 700°C --> value to be set: 711) by means of pitch potentiometer (outer potentiometer).

Please note that boiling water should not be used as a temperature reference as the boiling temperature is dependent on the atmospheric pressure.(If using a reference thermometer stating the precise temperature you may, however even use boiling water.)

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

09 / 12

3. Correctiontable: (typ. value)

-50 -46 160 160 370 369 580 587 790 802 1000 1007

-40 -37 170 169 380 379 590 597 800 812 1010 1016

-30 -28 180 179 390 390 600 607 810 822 1020 1026

-20 -19 190 189 400 400 610 618 820 832 1030 1035

-10 -10 200 198 410 410 620 628 830 842 1040 1045

0 0 210 208 420 421 630 639 840 852 1050 1054

10 10 220 218 430 431 640 649 850 862 1060 1063

20 20 230 228 440 441 650 659 860 871 1070 1073

30 29 240 238 450 452 660 670 870 881 1080 1082

40 39 250 248 460 462 670 680 880 891 1090 1091

50 49 260 258 470 472 680 690 890 901 1100 1100

60 59 270 268 480 483 690 700 900 911 1110 1110

70 70 280 278 490 493 700 711 910 920 1120 1119

80 80 290 288 500 504 710 721 920 930 1130 1128

90 90 300 298 510 514 720 731 930 940 1140 1137

100 100 310 308 520 524 730 741 940 949 1150 1146

110 110 320 318 530 535 740 751 950 959 1160 1155

120 120 330 328 540 545 750 762 960 969 1170 1164

130 130 340 339 550 556 760 772 970 978 1180 1173

140 140 350 349 560 566 770 782 980 988

150 150 360 359 570 576 780 792 990 997

tempe-

rature

display tempe-

rature

display tempe-

rature

display tempe-

rature

display tempe-

rature

display tempe-

rature

display

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

10 / 12

4. Specication

Range:

-50 to +1150°C

Resolution:

1°C

Accuracy:

Sensor::

<1% ±1 digit from -20 to +550°C and 920 to 1150°C, <1,5% ±1 digit from 550 to 920°C.

For more detailed values please refer to att. correction table.

NiCr-Ni, acc. to ½ DIN 43710 for plug-in operation (not included in scope of supply!)

Display:

approx. 13 mm high, 3½ digit LCD

Nominal temperature:

25°C (accuracy specied at this temperature)

Working temperature:

Atmospheric humidity:

0 to 45°C, please avoid quick temperature changes, if possible, otherwise a temperature

adjustment time of approx. 15 minutes has to be taken into account. 0 to 80 % r.F. (not condensing)

Power supply:

9V-battery type IEC 6F22 (included) as well as additional d.c. connector (internal pin Ø

1.9mm) for external 10-12V direct voltage supply. (suitable power supply: GNG10/3000)

Battery life time:

approx. 700 operating hours

Low battery warning::

„BAT“ displayed automatically in case of low battery

Dimensions of case:

approx. 142 x 71 x 26 mm (H x W x D), Impact-resistant ABS plastic housing, Front side

IP65, integrated pop-up clip for table top or suspended use.

Weight:

approx. 160g (cpl. device with battery)

EMV:

The device corresponds to the essential protection ratings established in the Regulations of the Council for the Approximation of Legislation for the member coutries regarding electromagnetic compatibility (89/336/EWG). Additional error: <1%

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

11 / 12

Articlename Articelnumber Description

Digital Quick-Response Thermometer HM 1150

0560 1150 1 x Digital Quick-Response Thermometer

HM 1150 with Operating Instruction on CD-R

Digital Quick-Response Thermometer HM 1150 Set

0560 1150-01 1 x Digital Quick-Response Thermometer

HM 1150 SET incl. 1 x Type K Probe with 130 mm nominal length and 3

mm diameter in a transportation case

Articlename Articelnumber Description

Immersion Probe type K for extreme use

0600 1205

Diameter 6 mm, nominal length 300 mm, Stainless steel B+B exklusive handhold, cabel length 1000 mm with

helix cable, Miniatureplug yellow, Measuringtip swagged

diameter=3,0x15 mm,

Measuring range -50...+850°C

Penetration Probe type K 0600 1105

Diameter 4 mm Stainless steel, handhold 15x90 mm PTFE, cabel length 1000 mm, FEP 0,22 qmm, Miniatureplug yellow,

Measuring range -50...+260°C

6. Optional Order Information

5. Scope of Delivery

Digital Quick-Response Thermometer HM 1150

Digital Quick-Response Thermometer HM 1150 SET

INSTRUCTION MANUAL

Technical changes reserved B+B 0141 0315-117 September 2010

12 / 12

General Questions

If you still have questions concerning this product of B+B Thermo-Technik GmbH, please do not hesitate to contact us at:

B+B Thermo-Technik GmbH

Heinrich-Hertz-Straße 4

D-78166 Donaueschingen

Germany

Tel.: +49 (0) 771 83160 Fax: +49 (0) 771 831650

E-Mail: info@bb-sensors.com bb-sensors.com

We wish you a successful measuring!

Your Temperature-Partner

B+B Thermo-Technik GmbH

All technical information’s in this document are proved by us with high accuracy and shall inform you about all application

possibilities. This information’s are not conrmed by us and need to be proved by every user in regard to his intended use of the

equipment. All foreign trade mark rights need to be considered.

Edition September 2010. This manual substitutes all former editions.

B+B Sensors HM 1150 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual