BBK LT3210 Service manual

LCD TELEVISION

LC-(26-32)HU36S

CONTENTS

Safety precautions………………………………………………………………………..…
Alignment instructions …………………………….…….…………………………………
Method of software upgrading……………………………………………………………..
Working principle analysis………………………………………….………….………….
Block diagram…………………………………..………………………………….…………
IC block diagram………………………………………………………………………..……
Wiring diagram …………………………………………………………………………….
Troubleshooting guide ………………………………………………………………..……
Schematic diagram…………………………………………………………………………
APPENDIX-A: Assembly list
APPENDIX-B: Exploded View

1
3
6
12
13
14
19
20
23

Attention: This service manual is only for service personnel to take reference with. Before

servicing please read the following points carefully.

Safety precautions

1. Instructions

Be sure to switch off the power supply before replacing or welding any components or
inserting/plugging in connection wire Anti static measures to be taken (throughout the entire
production process!):
a) Do not touch here and there by hand at will;
b) Be sure to use anti static electric iron;
c) It’s a must for the welder to wear anti static gloves.
Please refer to the detailed list before replacing components that have special safety requirements.
Do not change the specs and type at will.

2. Points for attention in servicing of LCD

2.1 Screens are different from one model to another and therefore not interchangeable. Be sure to
use the screen of the original model for replacement.

2.2 The operation voltage of LCD screen is 700-825V. Be sure to take proper measures in
protecting yourself and the machine when testing the system in the course of normal operation or
right after the power is switched off. Please do not touch the circuit or the metal part of the module
that is in operation mode. Relevant operation is possible only one minute after the power is
switched off.

2.3 Do not use any adapter that is not identical with the TV set. Otherwise it will cause fire or
damage to the set.

2.4 Never operate the set or do any installation work in bad environment such as wet bathroom,
laundry, kitchen, or nearby fire source, heating equipment and devices or exposure to sunlight etc.
Otherwise bad effect will result.

2.5 If any foreign substance such as water, liquid, metal slices or other matters happens to fall into
the module, be sure to cut the power off immediately and do not move anything on the module lest it
should cause fire or electric shock due to contact with the high voltage or short circuit.

2.6 Should there be smoke, abnormal smell or sound from the module, please shut the power off at
once. Likewise, if the screen is not working after the power is on or in the course of operation, the
power must be cut off immediately and no more operation is allowed under the same condition.

2.7 Do not pull out or plug in the connection wire when the module is in operation or just after the
power is off because in this case relatively high voltage still remains in the capacitor of the driving
circuit. Please wait at least one minute before the pulling out or plugging in the connection wire.

2.8 When operating or installing LCD please don’t subject the LCD components to bending, twisting
or extrusion, collision lest mishap should result.

2.9 As most of the circuitry in LCD TV set is composed of CMOS integrated circuits, it’s necessary
to pay attention to anti statics. Before servicing LCD TV make sure to take anti static measure and
ensure full grounding for all the parts that have to be grounded.

2.10 There are lots of connection wires between parts behind the LCD screen. When servicing or
moving the set please take care not to touch or scratch them. Once they are damaged the screen

1

would be unable to work and no way to get it repaired.
If the connection wires, connectors or components fixed by the thermotropic glue need to disengage
when service, please soak the thermotropic glue into the alcohol and then pull them out in case of
dagame.

2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead to
breakage of screen glass or damage to driving circuit. Therefore it must be packed in a strong case
before the transportation or handling.

2.12 For the storage make sure to put it in a place where the environment can be controlled so as to
prevent the temperature and humidity from exceeding the limits as specified in the manual. For
prolonged storage, it is necessary to house it in an anti-moisture bag and put them altogether in one
place. The ambient conditions are tabulated as follows:

Temperature Scope for operation 0 ~ +50 oC

Scope for storage -20 ~ +60 oC

Humidity Scope for operation 20% ~ 85%

Scope for storage 10% ~ 90%

2.13 Display of a fixed picture for a long time may result in appearance of picture residue on the
screen, as commonly called “ghost shadow”. The extent of the residual picture varies with the
maker of LCD screen. This phenomenon doesn’t represent failure. This “ghost shadow” may remain
in the picture for a period of time (several minutes). But when operating it please avoid displaying
still picture in high brightness for a long time.

3. Points for attention during installation

3.1 The front panel of LCD screen is of glass. When installing it please make sure to put it in place.

3.2 For service or installation it’s necessary to use specified screw lest it should damage the screen.

3.3 Be sure to take anti dust measures. Any foreign substance that happens to fall down between
the screen and the glass will affect the receiving and viewing effect

3.4 When dismantling or mounting the protective partition plate that is used for anti vibration and
insulation please take care to keep it in intactness so as to avoid hidden trouble.

3.5 Be sure to protect the cabinet from damage or scratch during service, dismantling or mounting.

2

Alignment instructions

1. Test equipment

PM5518 (video signal generator)
VG-849 (VGA signal generator)
CA210 (white balancer)

2 Alignment flow-chart

The alignment flow-chart is shown as fig-1

Check DDC, HDCP KEY, FLASH and POWER control IC

Combined test for general assembly

Factory initialization setup

IF channel voltage of TV and AGC voltage adjustment

White balance adjustment

Fig-1 adjustment flow-chart

3 Unit adjustments

Connect all the boards according to wiring diagram, connect with power and observe the display.
Method for entering factory menu: press “INPUT”, “2”, “5”, ”8” and “0” in turn to enter factory menu;
press “CH+” and “CH-” to select adjustment items and press “VOL+” and “VOL-” to adjust value
items, press “MENU” continuously to exit.

3.1 Initialization
Enter factory menu, select “OPTION” and “HOTEL OPTION” sub-menu, adjustment of items to see
table1.

Table1 sub-menu adjustment

Items Preset Introduce

HOTEL 0 1: HOTEL OPTION of factory menu is optional

0: HOTEL OPTION of factory menu is not optional

LOGO 1 1: display LOGO in no signal or turn on

0: no LOGO display

ADC PRESCALE 00A Adjust according different power consumption

SIF PRESCALE 000 Adjust according different power consumption

Performance check

Preset ex-factory

3

BACK LIGHT 28 Adjust according different screen

ALL COLOR 1 1: white balance of each channel auto offset based on the HDMI white

balance

0: white balance of each channel adjust the offset base separately

ISP 0 0: no unit upgrade on the assembly line

1: unit upgrade on the assembly line

NO STANDY 00 01: turn on; 00: memory function of turn on; 10: standby

INIT VOLUME 0-100 Volume of turn on

INIT CHANNEL 1-200 Channel of turn on

INIT SRC Source Source of turn on

EEPROM-MEMORAY

RECALL

> EEPROM Initialization (operate when EEPROM data chaos)

3.2 Adjustment for AFT voltage and AGC voltage of IF channel in TV

3.2.1 IF AFC adjustment
Disconnect J401(B face), input 38.9MHz PAL signal of 80dB from J401 near the socket, Adjust

L404 to value 0.9V of TP402. Enter factory menu, adjust TDA4470 from BG to LL, input 33.9MHz
SECAM signal of 80dB, adjust RP402 to value 0.9V of TP402, then wed J401.

3.2.2 IF AGC adjustment

Input 184.25MHz RF signal of 60DB from RF terminal, adjust RP401 to value 4V of TP404
and there should be no obvious snowy picture. Increase the signal to 90DBV and it should be
display normally and no obvious noise.

3.3 White balance adjustment

3.3.1 white balance adjustment of HDMI

a. Input VG-848 signal from HDMI: TIMING854(800* 600/60Hz) and eighth level gray-scale

signal of PAT920. Use color analyzer CA210 to adjust white balance.

b. Enter submenu of COLOR TEMP., Select 9300k of color temperature

c. Fixed value of B GAIN, adjust R GAIN and G GAIN, let the color coordinate of the seventh
level be 285 and 293. Fixed value of B OFF, adjust R OFF and G OFF, let the color coordinate of
second level be 285 and 293 and the brightness be about 3nit-10nit. Adjustment R GAIN, G GAIN,
R OFF and G OFF repeatedly until the value of the two levels gray-scale be 285 and 293.

3.3.2 VGA/YPBPR/AV white balance check and correct

a. Input VG-848 signal of VGA: TIMING854(800* 600/60Hz) (PATIERN:CROSS) and auto
adjust to full screen, then input PAT948 black/white signal, enter factory menu ADC ADJ, select
AUTOTUNE and wait for OK display. Input PAT920(8 gray levels), check if the white balance is
normal, if not, set ALL COLOR to 0 and fine adjust according the method of 3.3.1

b. connect VG-848 signal of YPBPR to YPBPR terminal and input TIMING972(1080i/60HZ)
color bar of PAT908(include black/white bar), Enter submenu of ADC ADJ, Select AUTOTUNE and
wait for OK display. Input PAT920(8 gray levels), check if the white balance is normal, if not, set ALL
COLOR to 0 and fine adjust according the method of 3.3.2

c. Input AV signal(PM5518, 8 gray levels) to VIDEO terminal, check if the white balance is
normal, if not, set ALL COLOR to 0 and fine adjust according the method of 3.3.2
Note: it can’t set back to 1 once ALL COLOR changes to 0.

4

4 Software upgrade

When software upgrading please enter factory menu first, enter ISP of OPTION, set ISP to 1 and
you can begin to upgrade. After upgrade finished, it needs to set ISP back to 0. If the picture can’t
display when upgrading, it needs to web J1 of 01S board. Please disconnect J1 again after
upgrading.

5 Performance check

5.1 TV function
Enter searching menu → auto search, connect RF-TV terminal with central signal source and check
if the picture is normal, if there are channels be skipped. Check TXT and parental control.

5.2 AV/S, YpbPr terminals
Input AV/S, YPbPr/YCbCr HD signal, check if it is normal.

5.3 VGA terminal
Insert VGA terminal, input VGA format signal of 640X480@60 Hz and check if the display is normal.

5.4 HDMI terminal
Insert HDMI terminal, input signal of 640 X 480@60 Hz signal and check if the display is normal.

5.5 check sound channel
Check the speaker and headphone of each channel.

5.6 RS232 terminal
Insert earphone to COM terminal and check if the long-distance control function is normal.

5.7 other function check
Check the turn on/turn off timer, asleep timer, picture/sound mode, OSD, freeze/mute, stereo, ect.

5.8 presetting before ex-factory

Item Setting Item Setting Item Setting

PICTURE MODE STANDARD BALANCE 50 OSD LANGUAGE English

COLOR MODE NORMAL VOLUME 50 OSD HPOSITION 50

NR WEAK SLEEP TIMER OFF OSD VPOSITION 50

ZOOM FULL TTX LANGUAGE WEST OSD HALFTONE 50

SOUND MODE STANDARD BLUE SCREEN OFF OSD DURATION 15

AVC OFF

5

Method of software upgrading

1. The tools and software demanded

1) Please confirm that PC has the software of ISP_TOOL and install the parallel interface drive
program Port95nt.

2) ISP_TOOL icon is bellow:

3) One serial cable (25 pins) and one VGA cable (15 pins), the serial cable connects the PC and the
upgrade instrument, the VGA cable connects the TV and the upgrade instrument.

2. The steps for upgrading software

1) Please confirm that the connection wires and the upgrade instrument are connected well before
the software written and then power on the TV.

2) Double click the icon ISP_TOOL to open it:

3) Press “Connect“ to connect TV, if the connection is done successfully as shown below, then
press “enter”.

6

Note: if it appears error, check the connection wires and check if ISP item of the factory menu is set
to 1, if not, please set it to 1.

4) After connection is done, it needs to read the Binary document. Press “Read” as shown below:

5) Search the document needed to write in the “Read” check box.

7

Select

6) Select the document then the window will appear as shown below:

8

7) Press “Auto” to select the writing function.

Select the items shown in the picture above:
(a) Read File

9

(b) Program
(c) Exit ISP
(d) Erase Device
(e) File Area

8) Press “Run” to begin the writing program, wait till the blue bar is complete.

After writing, it will display OK:

If there is error appeared (shown as below), press “Run” again to rewrite the program till it is
success.

10

Note1: keep the connection well and don’t cut off the power during the writing process.
Note2: the writing speed can be adjusted as shown below. Select “Config” then adjust Speed BAR,
the value is bigger the speed is faster. But it is easier to appear error when increase the speed, so it
need to select a suitable speed according the PC.

Step 1

Step 2

11

Working principle analysis of the unit

The RF signal received by antenna will be sent to tuner TUN401, then IF signal will be obtained
through high amplifier and mixed frequency, through pre-intermediate amplified by V408, then it will
be sent to acoustic surface-wave Z407 to do IF filter and get better IF characteristics, then it will be
sent to N404 (TDA4470) to do intermediate amplification, phase-locked loop VCO and synchronous
wave detection to get video signal TV-V; after pre-intermediate amplification IF will also be sent to
acoustic surface-wave Z406 to do filter at the same time, then it will be sent to N404 to do
intermediate amplification and output the second sound intermediate frequency signal (TV-SIF).

The TV-V signal output from TDA4470 together with TV-SIF will be sent to main IC
NS4(MST9E88L).

Video signals of AV1/S, VGA, YPbPr and HDMI will be sent to MST9E88L, too.

Video RGB of SCART1 and S-Y, S-C of SCART2 will still be sent to MST9E88L, and the audio
signal of them via audio switch N302(HEF4052BT) selection after also sent to MST9E88L.

The main IC NS4(MST9E88L) is a high performance and fully integrated IC, which can realize
HDMI processing, video demodulating, video switch selection, A/D and D/A conversion,
interlace/de-interlace processing, modes conversion, OSD and low-voltage differential output, ect.
And it also has functions of audio selection, processing and MCU.

The video signal via MST9E88L processing, output 4 pairs differential signal and 1 pair clock
signal for LCD panel display. TV-V output from TDA4470 via double video amplifying, it will be sent
to SCART1 for AV-OUT. AV processed by MST9E88L via double video amplifying will be sent to
SCART2 for AV-OUT, too.

Audio signal via MST9E88L processing will be sent to sound amplifier N405 (MP7722DF)
amplifying to speaker. The audio also sent to earphone amplifier N406(BH3547F) amplifying to
earphone. TV audio signal will be sent to D/A converter NS6(DS4344) through I2S bus converting to
analog audio signal TV-L/R, then sent to SCART1 for AV-OUT. At the same time, TV-L/R together
with AV-L/R processed by MST9E88L will be sent to audio switch NS8(HEF4052BT), after selecting
to SCART2 for AV-OUT.

12

Block diagram

HDMI

VGA

YPbPr

(DTV)

SCART1-RGB

SCART1-AV

SCART1-L/R

SCART2-L/R

SCART2-Y

EDID

24C02

HDTV SW.

PI5V330

AUDIO SW.

HEF4052

EDID

24C02

SCART2-C

Y/AV1

S-C

TUNER

TV-V

TV-SIF

L/R-VGA

L/R-YPbPr

L/R-AV1/S

AV- L / R

SCART1-V OUT TV-IIS

SCART2-L/R OUT

SCART2-V OUT CVBS

SCART1-L/R OUT

SAW

IF AMP

TDA4470

2*AMP

2*AMP

TV-L/R

POWER MEG.

AT M E G8 L

LCD TV

CONTROLLER

MST9X88LD

D/A

CS4334

HP AMP

BH3547F

AUDIO SW.

HEF4052

DDR

FLASH

EEPROM

HDCP KEY

PANEL

AUDIO AMP.

MP7722

SPEAKER

HEAD

PHONE

13

IC block diagram

1. MST9E88L

The MST9E88L is a high performance and fully integrated IC for multi-function LCD monitor/TV with
resolutions up to SXGA/WXGA. It is configured with an integrated triple-ADC/PLL, an integrated
DVI/HDCP/HDMI receiver, a multi-standard TV video and audio decoder, a video de-interlacer, a
scaling engine, the MStarACE-3 color engine, an on-screen display controller, an 8-bit MCU and a
built-in output panel interface. With external frame buffer, 3-D video decoding and processing are
fulfilled for high-quality TV applications. To further reduce system costs, the MST9E88L also
integrates intelligent power management control capability for green-mode requirements and
spread-spectrum support for EMI management.

14

2. MP7722DF

The MP7722 is a stereo 20W Class D Audio Amplifier. It is one of MPS’second generation of fully
integrated audio amplifiers which dramatically reduces solution size by integrating the following:
180mΩ power MOSFETs
Startup / Shutdown pop elimination
Short circuit protection
Mute / Standby
The MP7722 utilizes a single ended output structure capable of delivering 2 x 20W into 4Ωspeakers.
MPS Class D Audio Amplifiers exhibit the high fidelity of a Class A/B amplifier at efficiencies greater
than 90%. The circuit is based on the MPS’ proprietary variable frequency topology that delivers low
distortion, fast response time and operates on a single power supply.

15

16

3. TDA4470

The TDA4470 is an integrated bipolar circuit for multi-standard video/sound IF(VIF/SIF) signal
processing in TV/VCR and multimedia applications. The circuit processed all TV video IF signals
with negative modulation (e.g., B/G standard), positive modulation (e.g., L standard) and the AM,
FM/NICAM sound IF signals.

17

18

Wiring diagram

IF adjust

9

1

Trouble shooting

1. Fault clearance

Before servicing please check to find the possible causes of the troubles according to the table

below.

1.1 Antenna (signal):

Picture is out of focus or jumping  Bad status in signal receiving

 Poor signal

 Check if there are failures with the electrical connector or

the antenna.

 Check if the antenna is properly connected.

Fringe in picture  Check if the antenna is correctly oriented.

 Maybe there is electric wave reflected from hilltop or

building.

Picture is interfered by stripe shaped

bright spots

There appear streaks or light color

on the screen

1.2 TV set:

Symptoms Possible cause

Unable to switch the power on  Check to see if the power plug has been inserted properly

No picture and sound  Check to see if the power supply of liquid crystal TV has

Deterioration of color phase or color

tone

Screen position or size is not proper  Check is the screen position and size is correctly set up.

Picture is twisted and deformed  Check to see if the picture-frame ratio is properly set up.

Picture color changed or colorless  Check the “Component” or “RGB” settings of the liquid

 Possibly due to interference from automobile, train, high

voltage transmission line, neon lamp etc.

 Maybe there is interference between antenna and power

supply line. Please try to separate them in a longer

distance.

 Maybe the shielded-layer of signal wire is not connected

properly to the connector.

 Check if interfered by other equipment and if interfered

possibly by the equipment like transmitting antenna,

non-professional radio station and cellular phone.

into the socket.

been switched on. (As can be indicated by the red LED at

the front of the TV set)

 See if it’s receiving the signal that is transmitted from other

source than the station

 Check if it’s connected to the wrong terminal or if the input

mode is correct.

 Check if the signal cable connection between video

frequency source and the liquid crystal TV set is correct.

 Check if all the picture setups have been corrected.

crystal TV set and make proper adjustment according to the

20

signal types.

Picture too bright and there is

distortion in the brightest area

Picture is whitish or too bright in the

darkest area of the picture

No picture or signal produced from

the displayer if “XXX in search”

appears.

There appears an indication -

“outside the receivable scope)

Remote control cannot work

properly

No picture and sound, but only

hash.

Blur picture  Check if the antenna cable is correctly connected.

No sound  Check if the “mute” audio frequency setting is selected.

When playing VHS picture search

tape, there are lines at the top or

bottom of the picture.

 Check if the contrast setting is too high.

 Possibly the output quality of DVD broadcaster is set too

high.

 It maybe also due to improper terminal connection of the

video frequency signal in a certain position of the system.

 Check if the setting for the brightness is too high

 Possibly the brightness grade of DVD player (broadcaster)

is set too high.

 Check if the cable is disconnected.

 Check if it’s connected to the proper terminal or if the input

mode is correct.

 Check if the TV set can receive input signal. The signal is

not correctly identified and VGA format is beyond the

specified scope.

 Check if the batteries are installed in the reverse order.

 Check if the battery is effective.

 Check the distance or angle from the monitor.

 Check if there is any obstruct between the remote control

and the TV set.

 Check if the remote control signal- receiving window is

exposed to strong fluorescence.

 Check if the antenna cable is correctly connected, or if it

has received the video signal correctly.

 Of if it has received the right video signal.

 Check if the sound volume is set to minimum.

 Make sure the earphone is not connected.

 Check if the cable connection is loose.

 When being played or in pause VHS picture search tape

sometimes can’t provide stable picture, which may lead to

incorrect display of the liquid crystal TV, In this case please

press “auto” key on the remote control so as to enable the

liquid crystal TV set to recheck the signal and then to

display correct picture signal

21

2. Troubleshooting guide

k

f

p

d

n

2.1. No raster

Turn-on power supply, chec

if the red indicator is light in

the STANDBY?

no

Check if PIN3(5V) of main

board is normal?

no

Check STANDBY circuit o

ower supply board

Press POWER button in the

unit or sensor control an

check the indicator.

Check if the PIN12 of X301 in

main board is high-level?

no

Replace NS4

yes

blue

yes

Check back light board

Check N102 and its

peripheral circuit

red

no

Check if the PIN11 of X303 i

main board is high-level?

yes

Check power

supply board

20

2.2. Raster, but no picture

y

p

d

f

t

f

d

p

Check if the unit button

and remote control

operation?

yes

no

no

Replace

main board

Enter factory-menu,

initialization EEPROM,

then turn off the TV,

turn on again, displa

icture?

Adjust main boar

Does display OSD

menu in screen when

ress menu button?

yes

again

yes

Check TUNER401

and its periphery

yes

yes

Check if the all

channels have signal?

Which is no signal

Check if 1VPP signal

and noise wave o

X405(PIN 8) in the

TV board?

no

Check N404 an

its periphery

no

of channels

TV

no

Check if outpu

IF signal o

TUNER401(pin

11) is normal?

yes

HDMI/VGA/YPRPB

Replace

main board

21

2.3.no sound

d

f

N

N

p

p

p

Check if PIN2, 8,13 an

18 voltage of N405 is

normal?

Check power supply

no

yes

Check PIN3 and

PIN7 output wave o

405

no

Check PIN24 wave of

404

no

Check PIN11 wave of

TUNER401

no

Check TUNER401 and

its periphery

yes

yes

yes

Check N405 and its

eriphery

Check NS4 and its

eriphery

Check N404 and its

eriphery

22

page 1 of 4

page 2 of 4

page 3of 4

page 4 of 4

interface connector

KEY board

IR receiver board

TV board

26" power 1

26" power 2

32" POWER

26" backlight

26" T-CON

APPENDIX-A: Main assembly 9226HU3613

NAME NO.

Analog board
Main board

IR board
Interface conncetion board
Key board
T-CON board
Backlight baord
Power board
Remote control
Panel

6HU0495310
6HU0700150 NS4 MST9E88L (5270988002)

6HA00809A0
6HU0112910
6HU0150510
6HU0122610
6HU0121410
6HU0122010
6010Y03512
5203265502

APPENDIX-A: Main assembly 9232HU3630

NAME NO.

Analog board
Main board

IR board
Interface conncetion board
Key board
Power board
Remote control
Panel

6HU0495310
6HU0490120 NS4 MST9E88L (5270988002)

6HU0340910
6HU0264610
6HU02505A0
6HU0212010
6010Y03512
5203325903

MAIN COMPONENT AND IT'S NO.

N404
N405

RC-Y35-0K
V260B1-L02

TDA4470MFL (5274470001)
MP7722DF (5277722001)

MAIN COMPONENT AND IT'S NO.

N404
N405

RC-Y35-0K
LK315T3LZ54

TDA4470MFL (5274470001)
MP7722DF (5277722001)

APPENDIX: Exploded view LC-26X36

PART LIST OF EXPLODED VIEW

NO. DESCRIPTION

1 front cabinet
2 key board
3 T-COM board
4 T-COM board shielding cover
5 panel
6 backlight board
7 backlight board shielding cover
8 power board frame

9 panel frame
10 panel frame
11 main board frame
12 panel fixed bracket
13 power board
14 main board
15 analog board
16 AV baffle
17 key board baffle
18 back cabinet
19 speaker connection
20 stand assy
21 speaker back cover
22 AV baffle
23 power socket
24 interface connection board
25 wall mounting bracket
26 wall mounting connection
27 panel fixed bracket
28 IR board
29 speaker
30 speaker
31 light conductor column
32 panel connection bracket
33 power swtich bracket
34 acryl decorative piece
35 decorative bar

Note: Design and specifications are subject to change without notice.

APPENDIX-B: Exploded view (LC-32X36)

PART LIST OF EXPLODED VIEW

NO. PART NO. DESCRIPTION

1 585A423030 decorative board
2 5QG36L2010 front cabinet
3 IR board
4 key board
5 panel
6 58A004160E panel frame
7 58A0071400 panel fixed bracket
8 58A0057700 power board bracket

9 58A0C40700 panel frame
10 58A0A4060B panel frame
11 574G18801C main board frame
12 main board
13 analog board
14 5810A5071A AV baffle
15 5HG36LK010 back cabinet
16 6151085600 stand
17 58A004100A wall mounting bracket
18 581AA59810 AV baffle
19 interface connection board
20 power board
21 58B0033410 connection frame
22 58A004100A stand bracket
23 58A0D4080A panel frame
24 58A0041100 connection piece
25 58A004170C panel frame
26
27 58B0A33210 side AV bracket
28 615CA82420 speaker net

5500806004 speaker

Note: design and specifications are subject to change without notice.

9226HU3613
Ver.1.0