BBK 1777 Installation Instructions Manual

27427 BOSTIK COURT

TEMECULA, CA 92590

For any questions, email us:

[e-mail]

INSTALLATION INSTRUCTIONS
INS241

2011-2016 DODGE SRT8
CHALLENGER/CHARGER/300C 6.4L V8

COLD AIR INDUCTION

Part # 1777

Special Tools required:
No special tools required

!

Install Time: 30 minutes.

Diculty: Very easy.

INCLUDED IN THIS KIT

(1) Air filter

(1) Blue rubber coupler

(1) Inlet tube

(1) small rubber grommet

(1) Air shield

Foam edge trim

Vacuum hose

(1) Vacuum hose adapter

Instructions / BBK sticker

(3) Hose clamps

Small edge rubber trim

Note! The C.A.R.B. exemption sticker, (attached), must be visible under the hood so that an emissions inspector can see it

when the vehicle is required to be tested for emissions. California requires testing every two years, other states may vary.

IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.

BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.

WWW.BBKPERFORMANCE.COM

MADE IN U.S.A.

MADE IN U.S.A.

UPDATED LAST: September2017

27427 BOSTIK COURT

TEMECULA, CA 92590

For any questions, email us:

[e-mail]

FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION

STEP 1

Disconnect the negative battery terminal. Remove driver side engine cover.

STEP 2

Unplug the wiring harness that connects to the air temperature sensor on the

stock inlet tube.

STEP 3

Disconnect the vacuum line from the stock air box and valve cover and

remove completely.

STEP 4

Remove the bolt that holds that stock air box to the core support. Loosen

the clamp on the inlet tube at the throttle body. Remove the air box and inlet

tube from the vehicle by lifting up on the air box releasing it from its mounting

points and pull the inlet hose free from the throttle body.

STEP 5

Remove the rubber grommet from the bottom pin on the air box and put it

onto the pin on the bottom of the BBK Cold Air Shield.

STEP 8

Set the BBK Air Filter into the Air Shield and put the bottom of the air lter

through the hole in the air shield line up the barb tting coming out of the air

lter with the hole in the air shield. Place the hose clamp over the bottom of

the air lter once it is though the air shield.

STEP 9

Install the BBK Cold Air Tube into the inlet on the BBK air lter. Install the other

end of the Cold Air Tube into the rubber coupler on the throttle body. Adjust

the air tube for best tment and tighten down all clamps to secure the air lter

and air tube in place.

STEP 10

Install the vacuum hose that is supplied in the kit. Connecting it to the barb

tting on the air lter and the port on the valve cover. This hose will need to

be cut to size.

STEP 11

Reconnect the wiring harness plug onto the air temp sensor.

STEP 12

STEP 6

Set the BBK Cold Air Shield into place press the pin with the rubber grommet

into the hole in the inner fender. Re-install the bolt that was removed in step

4 and tighten it down.

STEP 7

Remove the air temp sensor from the stock inlet tube and Install the air temp

sensor into the rubber grommet on the BBK Cold Air Tube.

MADE IN U.S.A.

IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.

BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.

WWW.BBKPERFORMANCE.COM

Re-connect the negative battery terminal. Re-install the engine cover. Start

the vehicle and check for any air leaks.

YOUR INSTALL IS NOW COMPLETE.

NOTE

The C.A.R.B. exemption sticker, (attached), must be visible under the hood

so that an emissions inspector can see it when the vehicle is required to be

tested for emissions. California requires testing every two years, other states

may vary.

UPDATED LAST: September2017