B&B Electronics ZP24D-250RM-SR Quick Start Guide

Documentation Number –p/n 8576R1 ZPxxD-xxxRM-SR(MR)(LR-AU)-0812qsg
CChheecckk ffoorr AAllll RReeqquuiirreedd HHaarrddwwaarree
ZLINX™ Radio Modem (one of the following models)
o ZP24D-250RM-SR o ZP24D192RM-MR o ZP24D-96RM-MR o ZP9D-192RM-MR o ZP9D-96RM-MR o ZP9D-115RM-LR-AU
This Quick Start Guide CD with ZLINX™ Manager Software and manual Antenna Terminal Block (Attached) Additional items required but not included:
o 10 48 VDC / 18 30 VAC, 6.0 W Power Supply o Serial Cable
Special Precautions for UL
Maximum Ambient Air Temperature: 85°C (185°F)
Wiring Terminals: Copper Wire Only One Conductor per Terminal Wire Range 28 to 16 AWG Tightening Torque 1.7 lb-in Temperature Rating of Field Wiring – 105° C (221° F) sized for 60° C (140°F) ampacity.
Radio Modem Options Screen
Quick Start Guide
Zlinx™ Radio Modem
ZPxxD-xxxRM-SR(MR)(LR-AU)
IInnssttaallll ZZlliinnx
x
MMaannaaggeerr SSooffttwwaarree
Insert the CD into your CD ROM Drive. The Zlinx™
Manager Install Wizard should start. Follow the on­screen instructions to install the software.
If auto run is disabled, locate the Zlinx Manager file on
the CD and double click it. The Install Wizard should start. Follow the on-screen instructions.
2
1
SSttaarrtt tthhee ZZlliinnx
x
MMaannaaggeerr SSooffttwwaarree
Start the Zlinx™ Manager Software. Click the Radio Modem Button. Click the Radio Modem Configuration Button.
o Select your COM port and configure it for 9600 baud,
Data Bits: 8, Parity: None, Stop Bit: 1.
Click the Connect Button. When the software locates the Radio Modem, the Basic
Modem Settings Screen will be displayed. This screen will display the Model Number, Function Set Type, Firmware Version, Network Identifier, Destination Address, Baud Rate, and Parity.
If the settings where changed from the default, Auto
Modem Search can be used to locate the modem. The Auto Search will use a sequence of COM Ports and settings until a response is received. If there is still no response, double check the power supply and serial cable. Also, make sure that no other devices are attached and that the unit is not set to RS-422/485 2-
5
CCoonnnneecctt PPoowweerr SSuuppppllyy
A 10 to 48 VDC or 18 to 30 VAC external power supply
is required.
Connect the power supply to the power terminal block
located on the top of the radio modem.
3
4
CCoonnnneecctt SSeerriiaall CCaabbllee && AAnntteennnnaa
Connect a straight through RS-232 cable between the
Radio Modem and your PC.
Connect the antenna to the Radio Modem.
Zlinx™ Manager Start Screen
Documentation Number –p/n 8576R1 ZPxxD-xxxRM-SR(MR)(LR-AU)-0812qsg
Click the Update Button to store the settings. Click the Advanced Modem Settings TAB. Check the Power
Level (PL). Select the appropriate power level for your application. For bench testing, PL should be set to 0 and Radio Modems should be separated by at least 1 meter. When using higher power levels, separate the modems by at least 7 meters. PL is adjustable on SR and LR modems.
If you changed any settings, store them by clicking the
Update button.
SSeett uupp yyoouurr sseeccoonndd RRaaddiioo MMooddeemm
Exit Configuration. Power off the Radio Modem (wait at least
30 seconds before re-applying power to this Radio Modem.
Configure your second Radio Modem using the same
procedure. Do not proceed to the RSSI Range Test step until you have a second modem configured. Two properly configured units are required to proceed to the next step.
Configure the second unit with the same settings.
CCoonnffiigguurree ttoo MMaattcchh YYoouurr SSeerriiaall DDeevviicceess
Configure the Radio Modems to match the serial devices
you will be connecting to.
The DB9 is wired as a DCE device. If you are connecting to
another DCE device, a cross-over cable will be required.
For the RS-422/485 terminals, TD is output, RD is input.
Ensure you match the signal polarity.
o 2-Wire Mode: TDA(-), TDB(+), SW1 & 2
ON.
o Wiring Examples are located in the
manual.
You are now ready to install your Radio Modems in the field.
RRSSSSII RRaannggee TTeesstt
Set one the remote modem to Loopback Mode. Loopback
connections can be made using the RS-422/485 interface by setting switch 1 and 2 to ON and 3 and 4 to OFF (internal loopback with echo on). You can also use the DB9 connections by bridging pins 2 and 3.
On the Radio Modem that is NOT set up for Loopback Mode,
run the RSSI Range Test. Observe the following indications:
o The DATA and RSSI will flash as data is
sent between the two units.
o Test results will be displayed on the RSSI
Range Test Screen.
6
8
On-line Configuration Screen
Radio Modem Found Screen
Radio Modem Not Found Screen
SSeettuupp tthhee RRaaddiioo MMooddeemm
Select a unique Network Identifier. This is especially
important if you have other units operating in the same area.
Set the Destination Address to FFFF (broadcast). If desired, you can change the baud rate and parity on the
Basic Modem Settings Screen. Remember to change your COM port to match.
Basic Modem Settings Screen
7
Loading...