B&B Electronics USR604 Quick Start Guide

Product Overview
Serial
Ports
LEDs
USB Port
Terminal block and barrel jack
1
Install the Drivers
DIP
Switches
3
The USR602 can run on 5 V USB power if the host port is providing 500 mA. It can also be powered via the terminal block or barrel jack port.
4
Connect the Converter
When you connect the converter to the host computer’s USB port the Found New Hardware wizard will open. It will discover and install the USB device. Then it will discover and install each serial port. Allow Windows to install the converter “Automatically.” There is no need to connect to the Internet or Windows Update.
If a popup window says the software has not passed Windows logo testing, that’s OK. Just click on “Continue Anyway.”
click Advanced and set up the Advanced Properties. (Refer to manual for more information.)
6
Loopback Test
Set the converter to RS-232 mode using the DIP switches. Loopback pins 2 and 3. Using Hyper Termi­nal or similar program, connect to the COM port. Set the desired baud rate. Ensure that Hyper Terminal local echo is OFF. Transmit data. If the same character string is returned, the test is good.
To prevent installation errors, do not plug in the hard­ware until you have already installed the drivers.
Use the included CD to install the converter’s drivers in the attached PC.
2
DIP
Switches
Port 1
Port 2
Set DIP Switches
SW# RS-232 RS-422
1 Off ON Off ON 2 Off ON ON Off 3 Off ON Off ON
Off ON ON Off
4
RS-485
4-Wire
RS-485
2-Wire
When the wizard is complete the serial ports on the converter will appear in Windows Device Manager as new COM ports.
5
Configure the Serial Ports
Open Control Panel. Click “System” to open the Device Manager. Under “Ports,” double-click the port to be configured.
On the “Serial Port Properties” window, set the required communications parameters for the system with which you are communicating. If necessary,
7
LED Type
PWR
TX
RX
LEDs
Indication when ON
Computer is receiving adequate voltage and current from USB or power source
Serial interface is transmitting data
Serial interface is receiving data
Troubleshooting
One USB port is required for each installed device. The USB port can be native to the PC or it can be a USB port on a USB hub that is connected to a PC.
The device works with USB 1.1 or 2.0 ports. But it has a maximum USB data rate of 12 Mbps.
To verify the installation you may open the Windows Device Manager. Scroll down to Ports. Expand the flyout window. You should see the new ports. If there are no exclamation points or other trouble indicators the ports are installed correctly and ready for use.
Sleep & Hibernate: Windows 7 disables USB transmit while in Sleep & Hibernate.
Terminal Block
One conductor per terminal. Use copper wire only. Wire size 16 to 28 AWG. Tightening torque 5 KG -CM. Wire temperature rating: 105 °C (Sized for 60 °C ampacity
Information - FCC rules
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference that may cause undesired operation.
Information - UL Class 1 Div 2
Recommended Accessories
PS12VLB-INT-MED
Power Supply
http://www.bb-elec.com/ product_multi_family.asp? MultiFamilyId=133&Trail=
16&TrailType=Top
MDR-20-24
DIN rail mount power supply
http://www.bb-elec.com/ product_multi_family.asp? MultiFamilyId=133&Trail= 16&TrailType=Top
Fast, Easy Answers
Please double check S t e p 7.
You can also use your
smart phone to access complete documentation on our website. Simply scan the code to the right.
USR602
Two-port USB to
Serial Converter
First Things First...
Before you begin, be sure you have the following:
Q
S
tart
G
uide
uick
Suitable for use in Class 1, Division 2, Groups A, B, C and D Hazardous Locations, or Nonhazardous locations only. WARNING - EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE UNLESS THE AREA IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS. Install in accordance with control drawing number 9340R0. Ind. Cont. Eq. For HAZ LOC 3HTV E245458 Class I, Div. 2, Groups A, B, C & D Temp. Code: T4A
Document number – PN8940_R004_USR602_4712qsg
1-888-948-2248 | Europe: +353 91 792444
www.bb-elec.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: 815-433-5100 | Fax: 815-433-5109 www.bb-elec.com | E-mail: info@bb-elec.com
© 2011 B&B Electronics Manufac turing Comp any
USR602
Two Meter USB Cable
Panel mount adapters
DIN rail mount adapter
CD ROM with Drivers
Fast and easy on the web:
www.bb-elec.com
Loading...