RoHS compliant
1310 nm Single-mode Transceiver (S1.1)
Small Form Pluggable (SFP), 3.3V
155 Mbps SONET OC-3/SDH STM-1/125 Mbps Fast Ethernet
Features
RoHS compliant
Compliant with SONET/SDH standard
Compliant with Fast Ethernet standard
I ndustry standard small form pluggable (SFP)
package
Duplex LC connector
Di fferential LVPECL inputs and outputs
Single power s upply 3.3V
T TL signal detect indicator
Hot Pluggable
Class 1 laser product complies with EN 60825-1
Ordering Information
PART NUMBER INPUT/OUTPUT SIGNAL DETECT VOLTAGE TEMPERATURE
°
LS38-A3S-TC-N AC/AC TTL 3.3V
LS38-A3S-TI-N AC/AC TTL 3.3V
0°C to 70
-40°C to 85 °C
C
Absolute Maximum Ratings
PARAMETER SYMBOL MIN MAX UNITS NOTE
Storage Temperature TS
Supply Voltage Vcc
Input Voltage VIN
Output Current Io --- 50 mA
Operating Current IOP --- 400 mA
RoHS compliant
1310 nm Single-mode Transceiver (S1.1)
Small Form Pluggable (SFP), 3.3V
155 Mbps SONET OC-3/SDH STM-1/125 Mbps Fast Ethernet
Block Diagram of Transceiver
ELECTRICAL SUBASSEMBLY
DATA
DATA/
TX_DISABLE
TX_FAULT
(0)
(1)
(2)
DATA
DATA/
RX_LOS
Transmitter Section
The transmitter section consists of a 1310 nm InGaAsP laser in an eye safe optical subassembly (OSA) which mates to the fiber
LD Driver
&
Fault Sense
MOD_DEF
POST-Amp
&
LOS Detect
LASER
OPTICAL
SUB-
ASSEMBLIES
RRE-
AMPLIFIER
IC
TOP VIEW (Label side)
RECEPTACLE
Photo
Diode
DUPLEX SC
cable. The laser OSA is driven by a LD driver IC which converts differential input LVPECL logic signals into an analog laser
driving current.
TX_DISABLE
The TX_DISABLE signal is high (TTL logic “1”) to turn off the laser output. The laser will turn on when TX_DISABLE is low
(TTL logic “0”).
Receiver Section
The receiver utilizes an InGaAs PIN photodiode mounted together with a trans-impedance preamplifier IC in an OSA. This OSA
is connected to a circuit providing post-amplification quantization, and optical signal detection.
Receive Loss (RX_LOS)
The RX_LOS is high (logic “1”) when there is no incoming light from the companion transceiver. This signal is normally used by
the system for the diagnostic purpose. The signal is operated in TTL level.
RoHS compliant
1310 nm Single-mode Transceiver (S1.1)
Small Form Pluggable (SFP), 3.3V
155 Mbps SONET OC-3/SDH STM-1/125 Mbps Fast Ethernet
Pin Assignment
Pin-Out
PIN 11
PIN 10
Pin Signal Name Description
1 T
2 TX_FAULT Transmit Fault
3 TX_DISABLE Transmit Disable
4 MOD_DEF (2) SDA Serial Data Signal
5 MOD_DEF (1) SCL Serial Clock Signal
6 MOD_DEF (0) TTL Low
7 RATE SELECT Open Circuit
8 RX_LOS Receiver Loss of Signal, TTL High, open collector
9 R
10 R
11 R
12
13
14 R
15 V
16 V
17 T
18
19
20 T
Transmit Ground
GND
Receiver Ground
GND
Receiver Ground
GND
Receiver Ground
GND
RX−
RX+
Receiver Ground
GND
Receiver Power Supply
CCR
Transmitter Power Supply
CCT
Transmitter Ground
GND
TX+
TX−
Transmitter Ground
GND
Receive Data Bar, Differential PECL, ac coupled
Receive Data, Differential PECL, ac coupled
Transmit Data, Differential PCEL, ac coupled
Transmit Data Bar, Differential PCEL, ac coupled
RoHS compliant
1310 nm Single-mode Transceiver (S1.1)
Small Form Pluggable (SFP), 3.3V
155 Mbps SONET OC-3/SDH STM-1/125 Mbps Fast Ethernet
Eye Safety Mark
The LS3 series Single-mode transceiver is a class 1 laser
product. It complies with EN 60825-1 and FDA 21 CFR
1040.10 and 1040.11. In order to meet laser safety
requirements the transceiver shall be operated within the
Absolute Maximum Ratings.
Caution
All adjustments have been done at the factory before
the shipment of the devices. No maintenance and user
serviceable part is required. Tampering with and
modifying the performance of the device will result in
voided product warranty.
Note : All information contained in this document is subject to change without notice.