B&B Electronics I-7018 Datasheet

8-channel Isolated Analog Input Module
Model I-7018
I-7000 is a family of network data acquisition and control modules providing analog to digital, digital to analog, digital input/output, timer/counter and other functions. The modules can be remotely controlled by a set of commands.
The I-7018 is an 8-channel analog input module. The I-7018P supports more thermocouple types and enhances the measurement range of some types.
Specifications
Analog Input
Photo-isolation: 3750 Vrms
Type: mV, V , mA (with external 125 ohms resistor)
Thermocouple: Type J, K, T, E, R, S, B, N, C (for I-7018)
Type J, K, T, E, R, S, B, N, C, L, M (for I-7018P)
Channels: 8 differential or 6 differential and
2 single-ended by jumper select
Voltage range: +/-15mV, +/-50mV, +/-100mV,+/- 500mV, +/-1V,+/- 2.5V
Current range: +/- 20mA
Resolution: 16 bits
Sampling rate: 10 Samples/Second
Bandwidth: 15.7 Hz
Input impedance: 20M Ohms
Accuracy: ±0.1%
Zero drift: ± 0.5uV/°C
Span drift: 25ppm/°C
CMR @ 50/60 Hz: 150 dB
NMR @ 50/60 Hz: 100 dB
Over voltage protection: 35V (P-P)
Isolation: 3000VDC
Block Diagram
EEPROM
Embedded Cont r ol l er
Da t a + Da t a -
+Vs GND
International Headquarters:
815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com support@bb-elec.com
Integrate – Expand – Simplify B&B ELECTRONICS PRODUCT INFORMATION
+353 91 792444 Fax +353 91 792445
RS- 485
Interface
Po wer
Regul at or
I-7018/18P
Phot o- I sol at i on
ADC
+5V
707 Dayton Road P.O. Box 1040 Ottawa, IL 61350 USA
Westlink Commercial Park Oranmore Co. Galway Ireland
I-7018 / I-7018P - 5003 1/2
Models: I-7018, I-7018P
Feature/Benefits
3000 VDC isolated analog input
24-bit sigma-delta ADC to
provide excellent accuracy
Thermocouple direct connect with built-in CJC
Software calibration
Dual watchdog
PIN Assignments
Vin5+ Vin5­Vin6+ Vin6­Vin7+ INIT*/Vin7­(Y)DATA+ (G)DATA­(R)+Vs (B)GND
Vi n7+
Vi n7-
Vi n6+
MUX
+V
-V
Vi n6-
Vi n1+
Vi n1-
Vi n0+
Vi n0-
1
Vin4-
10
Vin4+ Vin3­Vin3+ Vin2­Vin2+ Vin1­Vin1+ Vin0­Vin0+
Thermocouple type: (C)
Type Range (C)
J -210~ +760
K -270~+1372
T -270~+400
E -270~+1000
R 0~+1768
S 0~+1768
B 0~+1820
N -270~1300
C 0~2320
L
M
L
DIN43710
-200~800
(For 7018P only)
200~100
(For 7018P only)
-200~900
(For 7018P only)
20
11
I-7018 / I-7018P - 5003 2/2
RS-485 Connector
Asynchronous 2-wire half-duplex Pluggable terminal block: Pitch 5.08mm
Baud Rate
1.2K/2.4K/4.8K/9.6K/19.2K/38.4K/57.6K/115.2K bps
Wire Connection
Analog Input Channel 0~5
Analog Input Channel 6~7
8 different modes INIT* mode
Power Requirements
Power input: +10 to +30 VDC input
Power Consumption
1.0Watt for I-7018 & I-7018P
Environmental
Storage temperature: -25 to 80°C (-13 to 176 °F) Operation temperature: -20 to 75°C (-4 to 167 °F) Humidity: 5 to 95%, non-condensing
Dimensions LxWxH: 120 x 72 x 33 cm
(47.2 x 28.4 x 13.0 in)
Certification: CE
International Headquarters:
815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com support@bb-elec.com
Integrate – Expand – Simplify B&B ELECTRONICS PRODUCT INFORMATION
+353 91 792444 Fax +353 91 792445
707 Dayton Road P.O. Box 1040 Ottawa, IL 61350 USA
Westlink Commercial Park Oranmore Co. Galway Ireland
Loading...