B&B Electronics H5CLR User Manual

1

™

www.factorymation.com1.800.972.0436

TECO Timer User Manual

TECO Timer User Manual

1.800.972.0436 www.factorymation.com

™

2

A : Signal ON delay 1 (Timer resets when power comes ON.)

A-1 : Signal ON delay 2 (Timer resets when power comes ON.)

A-2 : Power ON delay 1 (Timer resets when power comes ON.)

A-3 : Power ON delay 2 (Timer dose not reset when power comes ON.)

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Timing starts when the start signal goes ON. *Note1
The control output is controlled using a sustained or

one-shot time period.

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

Set value

DOWN

Timing starts when the start signal goes ON, and is reset
when the start signal goes OFF. *Note1
The control output is controlled using a sustained or one­shot time period.

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

Set value

DOWN

Timing starts when the reset input goes OFF.
The start signal disables the timing function (ie., same

function as the gate input).
The control output is controlled using a sustained or

one-shot time period.

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

Set value

DOWN

Timing starts when the reset input goes OFF.
The start signal disables the timing function (ie., same

function as the gate input).
The control output is controlled using a sustained or

one-shot time period.

t

0

0

t

0

0

t t a t - a

0

0

RLC5H

TIMING CHART(Output mode)

B : Repeat cycle 1 (Timer resets when power comes ON.)

SOURCE

Start signal

Gate

tt

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Timing starts when the start signal goes ON. *Note1
The status of the control output is reversed when time is up

(OFF at start).

B-1 : Repeat cycle 2 (Timer dose not reset when power comes ON.)

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Timing starts when the start signal goes ON. *Note1
The status of the control output is reversed when time is up

(OFF at start).

B-2 : Repeat cycle ON start (Timer resets when power comes ON.)

SOURCE

Start signal

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Timing starts when the start signal goes ON. *Note1
The status of the control output is reversed when time

is up (OFF at start).

D : Signal OFF delay (Timer resets when power comes ON.)

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

0

Set value

DOWN

0

The control output is ON when the start signal is ON
(except when the power is OFF or the reset is ON).

The timer is reset when the time is up.

E : Interval (Timer resets when power comes ON.)

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Timing starts when the start signal comes ON. *Note1
The control output is reset when time is up.

F : Cumulative (Timer does not reset when power comes ON.)

SOURCE

Start signal

Gate

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Start signal enables timing (timing is stopped when the start
signal is OFF or when the power is OFF)

A sustained control output is used.

C : Signal ON/OFF delay (Timer resets when power comes ON.)

SOURCE

Start signal

Reset

Control output

Set value

UP

0

Set value

DOWN

0

Timing starts when the start signal goes ON or OFF.
The status of the control output is ON when the start

signal goes ON or OFF.

*Note1. While the start signal is ON, the timer starts when power
comes ON or when the reset input goes OFF.

DIMENSION(mm)

RESET
START

RUN
OUT

GATE

K/P

RESET
START

GATE

RESET

RUN
OUT
K/P

RESET

H5CLR

H5CLR

h
m
s

-0

h
m
s

+0.5

45

45

+0.5

-0

80-SU + 05-Y + RLC5H

-0

+0.5

45

+0.5

45

-0