B&B Electronics GW-7472 Quick Start Guide

(

Eth e r N et/IP to Mod b u s RTU Gate wa yEth e r N et/IP to Mod b u s RTU Gate wa y

What’s in the shipping package?

The package includes the following items:

GW-7472

Installing software on your PC

Software CD

Install GW-7472 Utility:

The software is located at:

For GW-7472

English/ Dec 2010/ Version 1.0

Quick Start Guide

This Document)

(DC connector to

2-wire power cable)

CA-002

Fieldbus_CD:\EtherNetIP\Gateway\GW-7472\Utility

http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7472/utility/

GW-7472 Quick Start Guide

Connecting the Power and Host PC

1. Make sure your PC has workable network settings.

2. Disable or well configure your Windows firewall and anti-virus

firewall first, else the “Network Scan” on step 4, 5 and 6 may
not work. (Please contact with your system Administrator)

3. Check Init/Run DIP
switch if it is on Init

Eth e r N et/IP to Mod b u s RTU Gate wa yEth e r N et/IP to Mod b u s RTU Gate wa y

position.

4. Connect both the GW-7472 and your computer to the same
sub network or the same Ethernet switch, and power the GW­7472 on.

GW-7472 Quick Start Guide

Eth e r N et/IP to Mod b u s RTU Gate wa yEth e r N et/IP to Mod b u s RTU Gate wa y

Searching the GW-7472

1. Double click the GW-7472 Utility shortcut on the desktop.

2. Click the “Network Scan” button to search your GW-7472.

3. Select “C onfigure” or “Diagnostic” buttons to configure or test

the module

GW-7472 Quick Start Guide

Module configuration

1. Double click the GW-7472 Utility shortcut on the desktop.

2. Click the “Network Scan” button to search your GW-7472.

3. Select “Configure” buttons to configure the module

4. After setting, click the “U pdate Settings” button to finish the
configuration.

Eth e r N et/IP to Mod b u s RTU Gate wa yEth e r N et/IP to Mod b u s RTU Gate wa y

Item Settings (Init Mode)

IP

Gateway

Mask

192.168.255.1

192.168.0.1

255.255.0.0

GW-7472 Quick Start Guide

Item Descriptions:

Item Description

For configuration of the Address Type, Static IP Address,

Network Settings

Port Settings

Modbus Request
Command

Eth e r N et/IP to Mod b u s RTU Gate wa yEth e r N et/IP to Mod b u s RTU Gate wa y

Module Diagnostic

Subnet Mask and Default Gateway of the GW-7472
Please refer to section “4.2.1 Network Settings”

For configuration of the Baud Rate, Data Sizes, Parity,

Stop Bits, of the RS-485/RS-422 port of the GW-7472
Please refer to section “4.2.2 Serial Port Settings”

Modbus commands to communicate with the Modbus
slaves

Please refer to section “4.2.3 Modbus Request Settings”

1. Check Init/Run switch if it is on

Run position.

2. Reboot your GW-7472. Then, re­connect it by utility.

GW-7472 Quick Start Guide

Item Descriptions:

Item Description

Send UCMM packets or use the Forward_Open service to build

UCMM/Forward Open
Class 3 Behavior

Forward Open Class1
Behavior

the CIP class 3 connection to communicate with the GW-7472.
Please refer to section “4.3.1

Behavior”

Use the Forward_Open service to build the CIP class 1
connection to communicate with the GW-7472.
Please refer to section “4.3.2

Behavior”

UCMM/Forward Open Class 3

Forward Open Class 1

Response Message

Eth e r N et/IP to Mod b u s RTU Gate wa yEth e r N et/IP to Mod b u s RTU Gate wa y

EtherNet/IP packets responded from the GW-7472.

Related Information

GW-7472 Product page:

http://www.icpdas.com/products/Remote_IO/can_bus/GW-7472.htm

GW-7472 Documentations:

Fieldbus_CD:\EtherNetIP\Gateway\GW-7472\Manual

http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7472/manual/

GW-7472 Utility:

Fieldbus_CD:\EtherNetIP\Gateway\GW-7472\Utility

http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7472/utility/

GW-7472 firmware:

Fieldbus_CD:\EtherNetIP\Gateway\GW-7472\firmware

http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7472/firmware/

ICP DAS Web Site: http://www.icpdas.com
Contact Us (E-Mail): [e-mail]

Copyright @ 2010 by ICP DAS Co., Ltd. All Rights Reserved.