B&B Electronics EIRP410-2SFP-T User Manual

Manual

Elinx EIRP410-2SFP-T

8 Ports10/100 PoE with 2 combo 10/100/1000 or 100/1000 SFP Ports

Unmanaged Din Rail Ethernet Switch

EIRP410-2SFP-T

Documentation Number: EIRP410-2SFP-T-0912m

International Headquarters:

707 Dayton Road

Ottawa, IL 61350 USA

Phone [phone]

Website: www.bb-elec.com

Sales e-mail: [e-mail]

Technical Support: [e-mail] –

European Headquarters

B&B Electronics

Westlink Commercial Park

Oranmore, Co. Galway, Ireland

Phone [phone]

Website: www.bb-europe.com

Sales e-mail: [e-mail]

Technical Support: [e-mail]

Original – April 2011

©2011 No part of this publication may be reproduced or transmitted i n any for m or by any m eans, electronic or mechanical, including photography, recording, or any
information storage and retrieval system without writ ten consent. Information in this manual is subject to change without notice, and does not represent a commitment on
the part.
B&B Electronics Manufacturing shall not be liable for incidental or consequential damages resulting from the furnishing, performance, or use of this manual. All brand
names used in this manual are the registered trademarks of their respective owners. The use of trademarks or other designations in this publication i s for reference
purposes only and does not constitute an endorsement by the trademark holder.

Table of Contents

INTRODUCTION ..................................................................................................................... 1

The EIRP410-2SFP-T is an industrial Managed Ethernet switch that has 8 10/100TX PoE ports and 2

10/100/1000T/Mini-G B IC Combo ports. .............................................................................................................................. 1

Features ................................................................................................................................................................................... 1

Package Contents ................................................................................................................................................................... 2

HARDWARE DESCRIPTION .................................................................................................. 3

Physical Dimension ................................................................................................................................................................ 3

Front Panel ............................................................................................................................................................................. 3

Front Panel of the PoE Industrial Switch ............................................................................................................................ 3

Top View ................................................................................................................................................................................. 4

Top View of the PoE Injectors Industrial SwitchLED Indicators ..................................................................................... 4

LED Indicators ....................................................................................................................................................................... 5

Ports ......................................................................................................................................................................................... 6

RJ-45 ports ........................................................................................................................................................................... 6

2 Mini-GBIC combo port ..................................................................................................................................................... 8

Cabling .................................................................................................................................................................................... 8

Wiring the Power Inputs ..................................................................................................................................................... 11

Wiring the Fault Alarm Contact ......................................................................................................................................... 11

MOUNTING INSTALLATION ................................................................................................ 13

DIN-Rail Mounting .............................................................................................................................................................. 13

Wall Mount Plate Mounting ................................................................................................................................................ 15

NETWORK APPLICATION ................................................................................................... 16

Troubleshooting .................................................................................................................................................................... 17

TECHNICAL SPECIFICATION ............................................................................................. 18

Manual Documentation Number: EIRP410-2SFP-T-0912m i

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Introduction

The EIRP410-2SFP-T is an industrial Managed Ethernet switch that has 8 10/100TX PoE ports and 2 10/100/1000T/Mini­GBIC Combo ports.

Features

• System Interface/Performance

o RJ-45 ports support Auto MDI/MDI-X Function
o Embedded 8-ports PoE
o SFP (Mini-GBIC) supports 100/1000 Dual Mode
o Store-and-Forward Switching Archi tecture
o Back-plane (Switching Fabric): 5.6Gbps
o 1Mbits Packet Buffer
o 8K MAC Address Table
o Supports Wide Operating Temperature (-40

• Power Supply

o Redundant Power Design

• Case/Installation

o IP-30 Protection
o DIN Rail and Wall Mount Design

• Relay Alarm

o Relay output for port breakdown, power fail and alarm

o

C ~ 75oC)

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

Manual Documentation Number: EIRP410-2SFP-T-0912m

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

1

Package Contents

• 8 Ports10/100 PoE with 2 combo 10/100/1000 or 100/1000 SFP Ports Industrial Switch

• User manual

• Pluggable Terminal Block

• 2 wall mount plates and 6 screws

• One DIN-Rail (attached on the switch)

8 10/100TX + 2 10/100/1000T/100/1000 S FP Combo with 8 PoE Injectors Industrial Switch

User Manual block connector

Wall Mount Plate Screws DIN-Rail

Manual Documentation Number: EIRP410-2SFP-T-0912m 2

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Hardware Description

The following information is an introduction to the Industrial switch’s hardware spec, port, cabling information, and
wiring installation will be described.

Physical Dimension

8 Ports10/100 PoE with 2 combo 10/100/1000 or 100/1000 SFP Ports Industrial Switch dimension (W x D x H) are
72mm x 105mm x 152mm

Front Panel

The Front Panel of the 8 Ports10/100 PoE with 2 combo 10/100/1000 or 100/1000 SFP Ports Industrial Switch is shown
as below:

Front Panel of the PoE Industrial Switch

Manual Documentation Number: EIRP410-2SFP-T-0912m 3

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Top View

The top view of the 8 Ports10/100 PoE with 2 combo 10/100/1000 or 100/1000 SFP Ports I ndustrial Switch has one
terminal block connector of two DC power inputs.

Top View of the PoE Injectors Industrial Switch

Manual Documentation Number: EIRP410-2SFP-T-0912m 4

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Green

Power 1 is active

OFF

No power inputs

Green

Power 2 is active

OFF

No power inputs

Green

SFP port is linking

Blinks

Data is transmitting or receiving

OFF

Not connected to network

Green

Connected to network

OFF

Not connected to network

A powered device is connected utilizing Power over Ethernet on
OFF

No device is connected or power forwarding fails

LED Indicators

The diagnostic LEDs located on the front panel of the industrial switch provide real-time in formation of operation and
status. The following table provides the description of the LED status and their meanings for the switch.

LED Status Meaning

PWR1

PWR2

Red Power input 1 or 2 is inactive

Fault

OFF Power 1 & Power 2 are both active or no power inputs

Green Connected to network

P9, P10 (RJ-45)

Link/Active
(P9, P10)

P1 ~ P8
(Green)

P1 ~ P8
(Yellow)

Upper
LED

Blinking Networking is active

OFF Not connected to network

Green The port is operating at speed of 1000M

Lower
LED

OFF The port is disconnecte d or not operating at speed of 1000M

Blinking Networking is active

Yellow Ethernet port full duplex
Blinking Collision of packet occurs
OFF Ethernet port half duplex or not connected to network

FWD (P1 ~ P8)

Green

Manual Documentation Number: EIRP410-2SFP-T-0912m 5

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

the port

Ports

RJ-45 ports

The RJ45 copper ports support auto MDI/MDIX operation. This feature allows network connections to computers, servers, or
other switches using straight-through or crossover cables (See Figure below). Straight-through cable connections: pins 1, 2, 3
and 6, at one end of the cable, are connected straight-through to pins 1, 2, 3 and 6 at the other end of the cable. The table below
shows the 10BASE-T/100BASE-TX MDI and MDI-X port pin outs.

Manual Documentation Number: EIRP410-2SFP-T-0912m 6

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Cross Over Cable Schematic

Manual Documentation Number: EIRP410-2SFP-T-0912m 7

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

2 Mini-GBIC combo port

2 auto-detect combo Giga ports — RF45 or fiber. The gigabit Ethernet ports are shared with the mini-GBIC ports. RJ45
UTP (Gigabit Ethernet) ports can operate in half/full-duplex modes and work at speeds of 10/100/1000Mbps that support
auto-sensing technology to enable each port to detect the connecting speed. The mini-GBIC port is a socket fo r a mini­GBIC (SFP) fiber transceiver.

Cabling

• Use four twisted-p air, Category 5e or above cabling for RJ-45 port connection. The cable between the switch and

the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long.

• Use the mini-GBIC ports to uplink to another switch by inserting the mini-GBIC (SFP) transceiver.

To connect the transceiver and LC cable, please follow the steps shown below:
First, insert the transceiver into the SFP module. Notice that the triangle mark is the bottom of the module.

Figure 2.8: Transceiver to the SFP module

Manual Documentation Number: EIRP410-2SFP-T-0912m 8

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Figure 2.9: Transceiver Inserted

Second, insert the fiber cable LC connector into the transceiver.

Figure 2.10: LC connector to the transceive r

To remove the LC connector from the transceiver, press the upper side of the LC connector to release from the
transceiver and pull it out.

Manual Documentation Number: EIRP410-2SFP-T-0912m 9

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Figure 2.11: Remove LC connector

Second, push down the metal loop and pull the transceiver out by the plastic handle.

Figure 2.12: Pull out from the transceiver

Manual Documentation Number: EIRP410-2SFP-T-0912m 10

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Note

The wire gauge for the terminal block should be in the range between
12-24 AWG.

Wiring the Power Inputs

Wiring the Fault Alarm Contact

The fault alarm contact wired to pins 3 and 4 of the terminal block connector as the picture shows below. When the wires
are inserting the conn ected device will detect the fault status. The fault status includes power failure or port link failure.
Once one of the mentioned states occur an open circuit will exist. An application example for the fault alarm contact is
shown on the next page:

Manual Documentation Number: EIRP410-2SFP-T-0912m 11

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Manual Documentation Number: EIRP410-2SFP-T-0912m 12

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Rear Panel of the switch

Mounting Installation

DIN-Rail Mounting

The DIN-Rail is installed at the factory and maybe removed if needed.

DIN-Rail

1. First, insert the top of the DIN-Rail into the track.

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Manual Documentation Number: EIRP410-2SFP-T-0912m

13

2. Lightly push the DIN-Rail into the track.

3. Check the DIN-Rail to insure proper fit.

4. To remove the industrial switch from the track, reverse steps above.

Manual Documentation Number: EIRP410-2SFP-T-0912m 14

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Wall Mount Plate Mounting

1. Remove the DIN-Rail from the industrial switch.

2. Install the wall mount plate on the rear panel of the industrial switch.

Manual Documentation Number: EIRP410-2SFP-T-0912m 15

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Network Application

This segment provides the samples to help user have more actual idea of industrial switch application. For a sample application

of the industrial switch, see the figures below.

Manual Documentation Number: EIRP410-2SFP-T-0912m 16

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Troubleshooting

• Verify that you are using the appropriate power supply adapter. Do not use the power adapter wi th DC output higher than

the power rating of the device.

• Select the proper UTP/STP cable to construct your network. Use unshielded twisted-pair (UTP) or shielded twisted-pair

(STP) cable for RJ-45 con ne ctions: 100Ω Category 3, 4 or 5 cable for 10Mbps connections, 100Ω Category 5 cable for
100Mbps connections. Insure the length of any twisted-pair connection does not exceed 100 meters (328 feet).

• Diagnosing LED Indicators: The Switch can be easily monitored through panel LED’s. The LED’s will provide an easy

way of detecting power or communication problems.

• If the Industrial switch LED indicators function normal and the connected cables are correct but the packets still cannot

transmit, please check your system’s Ethernet devices’ configuration or status. The Ping test is a common method to
check Ethernet devices connections on the network.

Manual Documentation Number: EIRP410-2SFP-T-0912m 17

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Distance:

0 to 80 km, 1550 nm (9/125 μm, 19 PS/(nm*km))

Technical Specification

Standard

IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX/FX
IEEE802.3ab 1000Base-T
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3af Power over E t hernet

Protocol

Transfer Rate

Packet Buffer

MAC address

LED

Network Cable

CSMA/CD

14,880 pps for 10Base-T Ethernet port
148,800 pps for 100Base-TX/FX Fast Ethernet port
1,488,000 pps for Gigabit Fiber Ethernet port

1Mbits

8K MAC address table

8 ports 10/100TX : Link/Activity (Green), Full duplex/Collision
(Yellow), Power Feeding (Green)

Giga port: Link/Activity (Green)
Per unit: Power 1 (Green), Power 2 (Green), Fault (Red)

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5, 5e cable

EIA/TIA-568 100-ohm (100m)

100Base-TX: 2-pair UTP/STP Cat. 5/5E cable

EIA/TIA-568 100-ohm (100m)

1000Base-TX: 2-pair UTP/STP Cat. 5E cable

EIA/TIA-568 100-ohm (100m)

Multi mode:
0 to 5 km, 1300 nm (50/125 μm, 800 MHz*km)

Optical cable

Manual Documentation Number: EIRP410-2SFP-T-0912m 18

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

0 to 4 km, 1300 nm (62.5/125 μm, 500 MHz*km)
Single mode:
0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km))

Min. TX Output:

-36 to -32 dBm (Single mode); -34 to -30 dB m (Multi mode)

Multi mode: -20 dBm
Single mode: 0 to 40 km, -5 dBm; 0 to 80 km, -5 dBm

Max. TX Output:

Multi mode: -14 dBm
Single mode: 0 to 40 km, 0 dBm; 0 to 80 km, 0 dBm

Sensitivity:

Back-plane (Switching
Fabric)

Packet throughput
ability

Power Supply

Power Consumption

Install

Operating Temperature

5.6Gbps

8.3Mpps at 64bytes

External Power Supply: DC 48V
Redundant power DC 48V with connective removable terminal block

140 Watts (maximum)

DIN rail kit and wall-mount ear for DIN-type cabinet install and wall
mounting

-40oC ~ 75oC (Wide Operating Temperature model)

o

C ~ 60oC (standard model)

-10

Operating Humidity

Storage Temperature

Case Dimension

5% to 95% (Non-condensing)

-40oC to 85oC

IP-30, 72 mm (W) x 105 mm (D) x 152mm (H)

FCC Class A

EMI

CE EN61000-4-2/3/4/5/6/8/11/12
CE EN61000-6-2
CE EN61000-6-4

Manual Documentation Number: EIRP410-2SFP-T-0912m 19

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com

Safety

Stability testing

UL
cUL
CE/EN60950-1

IEC60068-2-32 (Free fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)

Manual Documentation Number: EIRP410-2SFP-T-0912m 20

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax [phone] – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph [phone] – Fax [phone] – www.bb-europe.com