B&B Electronics EIR618 User Manual

Quick Start Guide

Elinx Managed Ethernet Switch

EIR618 Series

o Ethernet Switch o Console Cable (RS-232 RJ-45 to DB-9) o CD with Support Manual o This Quick Start Guide o Panel Mount Bracket

o IP Address: 192.168.16.1 o Subnet Mask: 255.255.255.0 o Gateway: 192.168.16.254 o User Name: root, Password: root

Items Included

Default Settings

LED Chart

LED Status Meaning

PWR

PWR1

PWR2

Fault

R.M

LINK/ACT

Port 17/18*

SFP

Port

17/18*

RJ-45

1-16*

*Note

Green The Switch is powered on Off The Switch is powered off Green Power Source 1 is available Off Power Source 1 is unavailable Green Power Source 2 is available Off Power source 2 is unavailable Red Power or Port failure Off Normal Operation

Green Off

Green SFP Port is linked Blinking Data is being transmitted or received

Off Not connected to the network T Green Port is linked T Blinking Data is being transmitted or received T Off Not connected to the network B Green Operating at 1000M

Off Disconnected or below 1000M

B T Green Connected to the network T Blinking Data is being transmitted or received T Off Not connected to the network B Yellow Operating in full-duplex B Blinking Data collision B

Off Half-duplex or not connected

Ports 1 through 16 are 10/100 RJ-45, Ports 16 & 17 are 100/1000 RJ-45 or SFP.

The Switch is the master of a redundant ring (X-Ring)

The Switch is not the master of a redundant ring.

EIR618 Series-5107qsg

Hardware Installation

o Record the switch’s MAC Address in the space

provided. The MAC Address is printed on the product label. NOTE: Provide the MAC Address to your

Network Administrator. The Network Administrator should provide an IP Address, Subnet Mask, and Gateway.

o Select a mounting location and install with the attached

DIN rail clip or included panel mount kit.

o Connect power to the switch

o 12 to 48 VDC o Redundant inputs are available with fault

contacts.

NOTE: The installation of an SFP Module disables the associated RJ-45 Port.

o These instructions are for Web based management.

Refer to the User’s Manual for instructions concerning console management.

o Connect a switch port to a stand alone PC. Change the

PC’s network IP Address to allow it to connect to the switch (ex: 192.168.16.2). Use the default subnet mask and gateway.

o Launch the PC’s web browser and navigate to the

switch by typing the switch’s IP Address in the browser address window.

o Navigate the web page by expanding the folders on the

left side of the web page.

Log into the Switch

815-433-5100 Fax 433-5104 www.bb-elec.com

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA

European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland

+353 91 792444 Fax +353 91 792445

www.bb-europe

orders@bb-elec.com support@bb-elec.com

.com orders@bb-europe.com support@bb-europe.com

o Expand the “system tree” and select IP configuration. o Enter the IP Address, Subnet Mask, and Gateway

provided by your Network Administrator.

o Save changes. o Disconnect the stand alone PC and connect the switch

to the network.

o Inform your Network Administrator that the IP Address

has been changed.

o NOTE: The User Manual contains instructions for

assigning the IP Address from a DHCP Server and allowing the switch to be a DHCP Server.

IP Configuration

o This step should be accomplished by the Network

Administrator.

o Log onto the switch from a Network PC. o Expand the “System Tree” and select user

authentication..

o Enter the new User Name and Password. Record this

information in the space provided below. File this document for future reference.

o Click the Apply button.

USER NAME: ______________________________________ PASSWORD:_______________________________________ MAC ADDRESS: ____________________________________ IP ADDRESS: _______________________________________

User Name and Password

Basic Configuration is complete. A comprehensive Manual is contained on the CD ROM. Refer to this manual to configure the advanced features of this switch.