B&B Electronics EIR510 User Manual
P
Quick Start Guide
Elinx Managed Ethernet Switch
EIR510 Series
1
Items Included
o Ethernet Switch
o Console Cable (RS-232 RJ-45 to DB-9)
o CD with Support Manual
o This Quick Start Guide
o Panel Mount Bracket
2
Default Settings
o IP Address: 192.168.16.1
o Subnet Mask: 255.255.255.0
o Gateway: 192.168.16.254
o User Name: root, Password: root
3
LED Status Meaning
PWR
PWR1
PWR2
Fault
R.M
LINK/ACT
(P9/P10)
Top Green Connected to the network
Top Blinking Transmitting or receiving
Top Off Not connected to the network
1-8
Bottom Orange Operating at full-duplex
Bottom Blinking Collision
Bottom Off Half-duplex or not connected
4
o Record the switch’s MAC Address in the space
o Select a mounting location and install with the attached
o Connect power to the switch
Green The Switch is powered on
Off The Switch is powered off
Green Power Source 1 is available
Off Power Source 1 is unavailable
Green Power Source 2 is available
Off Power source 2 is unavailable
Orange A power or port failure has occurred
Off Normal Operation
Green
Off
Green The port is linked
Blinking Data is being transmitted or received
Off Not connected to the network
Hardware Installation
provided. Provide the MAC Address to your Network
Administrator. The Network Administrator will
provide an IP Address, Subnet Mask and Gateway.
DIN rail clip or included panel mount kit.
o 24 to 48 VDC
o Redundant inputs are available with fault
LED Chart
The Switch is the master of a redundant
ring (X-Ring)
The Switch is not the master of a
redundant ring.
contacts.
EIR510 Series-5107qsg
5
o These instructions are for Web based management.
Refer to the User’s Manual for instructions concerning
console management.
o Connect a stand alone PC to a port on the switch.
Change the PC’s network IP Address to allow it to
connect to the switch (ex: 192.168.16.2). Use the
default subnet mask and gateway.
o Launch the PC’s web browser and navigate to the
switch by typing the switch’s IP address in the browser
address window.
o Navigate the web page by expanding the folders on the
left side of the web page.
Log into the Switch
815-433-5100 Fax 433-5104 www.bb-elec.com
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
+353 91 792444 Fax +353 91 792445
www.bb-europe
orders@bb-elec.com support@bb-elec.com
.com orders@bb-europe.com support@bb-europe.com
EIR510 Series-5107qsg
76
User Name and Password
IP Configuration
o Expand the “system tree” and select IP configuration.
o Enter the IP Address, Subnet Mask, and Gateway
provided by your Network Administrator.
o Save the changes.
o Disconnect the stand alone PC from the switch and
connect the switch to the network.
o Inform the Network Administrator that the IP Address
has been changed.
o NOTE: The User Manual contains instructions for
configuring the IP Address from a DHCP Server and
to allow the switch to act as a DHCP Server.
o This step should be performed by the Network
Administrator.
o Log onto the switch from a PC connected to the
network.
o Expand the “System Tree” and select user
authentication..
o Enter the new User Name and Password. Record this
information in the space provided below. File this
document for future reference.
o Click the Apply button.
USER NAME: ______________________________________
PASSWORD:_______________________________________
MAC ADDRESS: ____________________________________
IP ADDRESS: _______________________________________
Basic Configuration is complete. A
comprehensive Manual is contained on the CD
ROM. Refer to this manual to configure the
advanced features of this switch.
815-433-5100 Fax 433-5104 www.bb-elec.com
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
+353 91 792444 Fax +353 91 792445
www.bb-europe
orders@bb-elec.com support@bb-elec.com
.com orders@bb-europe.com support@bb-europe.com
Loading...