B&B Electronics EIR30x Datasheet

EIR30x series-4206ds - 1/2

Model: EIR30x series

Hardened Compact Ethernet Switches

Description

This quick installation guide describes how to install and use the hardened compact Ethernet Switch. Capable of

operating at temperature extremes of -34 to +74°C, this is the switch of choice for harsh environments constrained by space.

Physical Description

Terminal Block and Power Inputs

Terminal Block

PWR1 Power Input 1 (+24VDC) GND Power Ground PWR2 Power Input 2 (+24VDC) GND Power Ground

FAULT

There are two pairs of voltage inputs that can be used to power up this switch. Redundant voltage supplies are supported. You only need one voltage supply connected to run the switch.

10/100BaseTX and 100BaseFX Connectors

10/100BaseTX Connections

The following diagram lists the pinouts of 10/100BaseTX ports.

100BaseFX Connections

Fiber Port Pinouts

The Tx (transmit) port of device I is connected to the Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx (transmit) port of device II.

Pin Regular Ports Uplink Port

1 Input Receive Data + Output Transmit Data + 2 Input Receive Data - Output Transmit Data 3 Output Transmit Data + Input Receive Data + 4 NC NC 5 NC NC 6 Output Transmit Data - Input Receive Data 7 NC NC 8 NC NC

Earth Ground

The relay opens if PWR1 or PWR2 fails (1A)

815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com support@bb-elec.com

PRODUCT INFORMATION B&B ELECTRONICS

+353 91 792444 Fax +353 91 792445

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA

European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland

www.bb-europe.com orders@bb-europe.com support@bb-europe.com

EIR30x series-4206ds - 2/2

LED State Indication

Steady Network connection established, LNK stands for LINK LNK/ACT

(Green)

(Yellow)

Flashing Transmitting or receiving data, ACT stands for ACTIVITY

Steady 100 Mbps data 10/100

Off 10 Mbps data

Functional Description

• Meets NEMA TS1/2 Environmental requirements for temperature, shock, vibration for traffic control equipment.

• Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment.

• Support 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, Full/half-duplex; Auto MDI/MDIX.

• 100BaseFX: Multi mode SC or ST type; Single mode SC type.

• Support 2K MAC addresses. Provides 96K bytes memory buffer.

• Alarms for power failure by relay output.

• Redundant 10-30 VDC terminal block power inputs.

• Operating temperature ranges from -34 to 74°C.

• Supports Din-rail mounting installation.

Assembly, Startup, and Dismantling

• Assembly: Place the switch on the DIN rail from above using the slot. Push the front of the switch toward the mounting surface until it audibly snaps into place.

• Startup: Connect the supply voltage to start up the switch via the terminal block.

• Dismantling: Pull out the lower edge and then remove the switch from the DIN rail.

Specifications

Hardened Compact Switch Applicable Standards

Switching Method Forwarding Rate

10BaseT: 100BaseTX/FX:

Performance Cable

10BaseT: 100BaseTX: 100BaseFX:

LED Indicators Per unit – Power status (PWR1, PWR2)

Dimensions / Net Weight W13.5 cm × D12.5 cm × H5 cm Compact Size / 0.8kg approx.

Power Input Power Consumption

Operating / Storage Temperature -34°C to 74° C / -45°C to 93°C Humidity 10%-95% non-condensing Safety UL/CUL 60950, EN60950, IEC 60950, IEC61000-6-2 Emissions FCC Class A, CE Class A

10/100BaseT/TX auto-negotiating ports with RJ-45 connectors, 100BaseFX fiber ports IEEE 802.3 10BaseT, IEEE 802.3u 100BaseTX/FX Store-and-Forward

10 / 20Mbps half / full-duplex 100 / 200Mbps half / full-duplex

148,80pps for 10Mbps, 148,800pps for 100Mbps

2-pair UTP/STP Cat. 3, 4, 5 up to 100m 2-pair UTP/STP Cat. 5 up to 100m MMF (50 or 62.5µm), SMF (9 or10µm)

Per port – LNK/ACT – (Green) 10/100TX or 100FX, 100 – (Yellow) 10/100TX or 100FX

Terminal Block: 24VDC @ 400mA

9.6W Maximum

Name: B&B Electronics Manufacturing Company

Address: P.O. Box 1040 707 Dayton Road

Model Numbers: EIR305-1ST, EIR305-1SC, EIR306, EIR308, EIR308-2ST, EIR308-2SC, EIR308-2SC-SM

Description: 5, 6, 8 port Ethernet Switches[ Type: Light industrial ITE equipment Application of Council Directive: 89/336/EEC

Standards: EN 55022 EN 61000 (-3-2, -3-3) EN 61000 (-4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11)

Michael J. Fahrion, Director of Engineering

DECLARATION OF CONFORMITY