EIR102 Series Quick Start
Guide
Package Contents
• EIR102 Series Industrial Media Converter
• Quick Start Guide (One per shipment)
• Power Terminal Block (installed)
• Fiber Optic Dust Covers (installed on fiber optic models)
If any item is missing or damaged, contact B&B Electronics
for a replacement
Front Panel
1 Power Terminal Block 2 Position, Removable
2 PWR LED ON When Power Applied
3 Fiber Optic SPD LED Normally OFF
3 Fiber Optic LINK LED On When Fiber Port Linked
4 Fiber Optic Ports No. & Type Depends on Model
5 RJ45 SPD LED ON if 100 mbps
5 RJ45 LINK LED ON When RJ45 Port Linked
FLASHES When Data Transmitted
6 DIP Switch 4 POS for Fiber to Fiber
6 POS for Copper to Fiber
7 RJ45 Port Depends on Model
DIN Rail Mounting
B&B ELECTRONICS QUICK START GUIDE
1. Slide and hold the DIN Clip toward the bottom of the
Media Converter. Angle the top portion of the DIN mount
over the top of the DIN rail.
2. Move the Media Converter so that it is parallel with the
DIN Rail.
3. Release the DIN clip. The spring should return it to its
original position.
+353 91 792444 Fax +353 91 792445
© 2008 by B&B Electronics. All rights reserved.
EIR102 1308qsg-1/2
Configure DIP Switch
1. Fiber to Copper
models have a 6
position switch.
2. Fiber to Fiber models
have a 4 position
switch.
3. Switches are
numbered from the
bottom.
4. Cycle power after
changing DIP Switch
configuration.
1. Loosen the screw to open the terminal block lead clamp.
2. Insert the power lead. TB will accept 12-28 AWG wire.
3. Tighten the screw to close the terminal block lead clamp.
NOTE: For replacement Terminal Block order Part # 7444.
815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com support@bb-elec.com
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
www.bb-europe.com orders@bb-europe.com support@bb-europe.com
Attach Power Leads
External Supply Required
Warning: Work Safe – Equipment
damage or electrical shock hazard
exists. DO NOT ATTACH OR REMOVE
LEADS WITH THE POWER SUPPLY
ENERGIZED!
Ensure the clamp holds the lead securely. However, do not
over tighten.
Attach RJ45 Cable
If equipped)
Female Connector
1. Auto MDI/MDI-x is
supported. A straight
through or cross-over
cable may be used.
2. 10/100BaseT auto
negotiation and full/halfduplex are supported.
Speed and duplex can
also be forced. Refer to
DIP Switch settings.
MDI Cable Pinout
Pin Signal
1 Tx+
2 Tx3 Rx+
6 Rx-
MDI-X Cable Pinout
Pin Signal
1 Rx+
2 Rx3 Tx+
6 Tx-
Attach Fiber Optic Cable
Warning: Work Safe – This is a Class I
Laser/LED device. To avoid causing
serious damage to your eyes, DO NOT
STARE DIRECTLY INTO THE LIGHT.
1. Ensure your fiber optic cable is terminated with
the correct connector type. EIR102 Media
Converters use SC or ST connectors.
2. Fiber optic type for each port is located on the
product’s side label. When connecting the cable
to the media converter, be sure to line up the
slider guide on the cable and media converter
B&B ELECTRONICS QUICK START GUIDE
connectors.
3. Connect the fiber optic transmitter to the
downstream device’s receiver and vice-versa.
© 2008 by B&B Electronics. All rights reserved.
EIR102 1308qsg-2/2
Fiber Optic Cable
Inf
rmation
Mode and Distance Type Wavelength
Multi-mode (2 km) 62.5/125 µm 1310 nm
Single-mode (15 km) 9/125 µm 1310 nm
Single-mode (40 km) 9/125 µm 1310 nm
Single-mode (80 km) 9/125 µm 1550 nm
Output Power RCVR Sensitivity
Multi-mode (2 km) -19 to -14 dBm ≤ -32 dBm
Single-mode (15 km) -15 to -8 dBm ≤ -32 dBm
Single-mode (40 km) -5 to 0 dBm ≤ -34 dBm
Single-mode (80 km) -5 to 0 dBm ≤ -34 dBm
Fiber Optic Cable Information
Installation Complete
1. When the network cables are attached and power
is applied, installation is complete.
NOTE: Recycle power if DIP Switch changes are
made after power up.
Mechanical Diagram
815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com support@bb-elec.com
+353 91 792444 Fax +353 91 792445
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
www.bb-europe.com orders@bb-europe.com support@bb-europe.com