B&B Electronics ABDN-SE-IN5420 Quick Start Guide

Continuing section 6
Use the Help features of the interface to help you configure the device. When you are done with configuring the device, press ‘Commit’ to save the changes, then ‘Restart’ to restart the device. You can optionally press ‘Reload’ if you have further configuration changes to make.
7
If your device is connected and configured correctly, you will see the following LED Status:
COMM: GREEN LINK: GREEN POST: GREEN POWER: BLUE
LED Airborne Device State
POWER
POST
LINK
COMM
PIN
1 No Connect No Connect
2 RxD RxD+
3 TxD TxD+
4 No Connect No Connect
5 GND GND
6 No Connect RxD-
7 RTS No Connect
8 CTS No Connect
9 No Connect TxD-
Document number – PN710-00051-00_R000_ABDx-SE-IN54xx_1413qsg
Check Your Setup
Adapter is not powered.
Adapter is powered
Adapter is not powered.
Adapter failed Power On Self Test (POST) and is not configured for wireless communication.
Adapter passed POST but is not configured for wireless network communication.
Adapter passed post and is configured for wireless communication.
Adapter is not powered.
(Periodic Blinking) Adapter is searching for a valid net­work (Access Point) that matches device’s configuration.
Adapter has successfully associated with an Access Point.
If Power LED is also Off then Adapter is not powered.
If Power LED is On then: No TCP session from WLAN or Ethernet interface has been established.
A TCP connection to the adapter has been established from the Wireless or Ethernet interfaces but no traffic has been detected.
RS-232 (DTE) Port 1 & 2 (Default
RS-422/485
Recommended Accessories
PS-SDS 120VAC/5VDC Power Supply
http://www.bb-elec.com/Products/ Power-Supplies-Accessories/Wall­Transformer-Power-Supplies/Power­Supplies.aspx
Serial Cables
http://www.bb-elec.com/Products/ Power-Supplies-Accessories/Serial­Cables.aspx
Fast, Easy Answers
First, check your LEDs.
Then use your smart phone to access complete documentation on our web site. Simply scan the code to the right or visit the B&B Electronics Knowledge Base: http://support.bb-elec.com/knowledgec.aspx
1-888-948-2248 | Europe: +353 91 792444
www.bb-elec.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: 815-433-5100 | Fax: 815-433-5109 www.bb-elec.com | E-mail: info@bb-elec.com
© 2013 B&B Elect ronics Manuf acturing Co mpany
ABDx-SE-IN54xx
Industrial Serial Device Server
First Things First...
Before you begin, be sure you have the following:
ABDx-SE-IN54xx CD with Airborne Management Center software 5-36 VDC power for terminal block or a 5 VDC Power Supply (not included)
50 ohm, omni-directional antenna
Fast and easy on the web:
www.bb-elec.com
Product Overview
When AMC starts, it will request a login:
AMC will display the found Airborne device(s):
LEDs
Antenna
Antenna Port
LAN Port
Detachable
Power
Port
Terminal Block
1
Connect the Antenna to the antenna connector located on the side of the device.
2
Connect a CAT5 Ethernet cable between the device and an Ethernet port on a host computer.
Attach the Antenna
Connect Ethernet
Select Group Name: “manuf” and enter Group Password: “dpac”
AMC will load and discover the attached device:
Note: You may be required to wait up to 180 seconds before the device is discovered and displayed.
5
Manage Your Device
AMC will ask if you want to manage the new device, select ‘Yes’:
Right click the device’s name. Under “Connectivity Tools” choose “launch Web browser for OEM-Cfg1.” This will open the device’s browser-based management window.
6
Login to web interface:
Username “dpac” Password: “dpac”
Configure Your Device
3
Connect the 5-36 VDC terminal block attachment or use the AC power supply (optional).
4
Run the Airborne Management Center (AMC) application. If you don’t currently have AMC installed, you can install it from the included CD or download and install it from the B&B website. Just search for the model number and follow the links to download software from the Downloads section of the product page
Connect Power Supply
Connect to the Device
Select ‘Yes’ to indicate device is using Factory Default settings:
Continue configuration via the Web interface. Start with the Configuration -> Express Setup page.
Continued on the next page...
Loading...