B&B Electronics 9POP4 Quick Start Guide
Documentation Number –PN 9093R1 9POP4-0712qsg
CCeerrttiiffiiccaattiioonnss
FCC Class B
CE
o EN 55022: 2006 + A1:2007 Class A Emissions
o EN 61000-6-1: 2007 Generic Standards for
Residential, Commercial and Light-Industrial
Environments
o EN 61000-4-2: 2008 Electro-Static Discharge
(ESD)
o EN 61000-4-3: 2006 Radiated Field Immunity
(RFI)
o EN 61000-4-4: 2004 Electrical Fast Transients-
Burst (EFT)
o EN61000-4-5: Ed2, 2005 (Surge)
o EN 61000-4-6: 2005 Conducted Immunity
CChheecckk ffoorr AAllll RReeqquuiirreedd HHaarrddwwaarree
9POP4 RS-232 Optical Isolator
This Quick Start Guide
12VDC Wall Power Supply (sold separately).
Recommended Power Supplies:
o US – 232PS
o UK – PS1UK-1000
o EU – PS1EU-1000
Quick Start Guide
9POP4
Optically Isolated RS-232
Repeater
DDBB99 PPiinn--oouutt
1. DTE stands for Data Terminal
Equipment: these include Computers,
PLC's, and most devices which are not
used to extend communications. Think
COMPUTER for DTE.
2. DCE stands for Data Communications
Equipment: these includes devices
intended to plug directly into a DTE
port, Modems and devices that extend
communications like a modem, such
as RS-422, RS-485, or Fiber Optic
converters or Radio Modems. Think
MODEM for DCE.
3. On the DCE (female) side, Pins 1, 4,
and 6 are tied together internally.
4. On the DTE (Male) side, Pins 4 and 6
are tied together internally.
2
1
Connectors
A
DB9 Female – Data Communications Equipment
(DCE)
A
DB9 Male – Data Terminal Equipment (DTE)
C
Power – 12 VDC Jack, 2.5 mm Center Positive
Pin
Signal
DCE
DTE 1 DCD
Output
Input
2
RD
Output
Input
3
TD
Input
Output
4
DTR
Input
Output
5
GND
---
--- 6 DSR
Output
Input
7
RTS
Input
Output
8
CTS
Output
Input
9
RI
Output
Input
3
4
©2010 B&B Electronics Manufacturing Company
IInnffoorrmmaattiioonn
–
–
CCoonnnneeccttoorrss
Put
Documentation Number –PN 9093R1 9POP4-0712qsg
5
WWiirriinngg EExxaammppllee
PPoowweerr
1. The two sides of the isolator are
powered from a single +12VDC power
supply and maintain isolation. This
powering configuration allows the
device to be run in any system with
only a single supply, regardless of the
power levels on the RS-232 ports.
2. In order to maintain the required
isolation, use the recommended
power supply. Using an unregulated
power supply may negate the
isolation.
3. Recommended Power Supplies:
a. US – 232PS
b. UK – PS1UK-1000
c. EU – PS1EU-1000
LLooooppbbaacckk TTeesstt
Use a DB9 Female to DB9 Male cable to connect a
PC to the DCE port.
(Recommended) Connect a DB9 Female to DB9
Female cable to the DTE port.
On the DTE Port, jumper pin 2 to 3 and pin 7 to 8 on
the female end of the cable. This loops TD to RD and
CTS to RTS.
Using hyper terminal or similar program, connect to
the appropriate COM port (remember to set the baud
rate to 9600).Turn off hyper terminal local echo
Transmit data. The same data should be returned.
6
7
©2010 B&B Electronics Manufacturing Company
Loading...