B&B Electronics 858-18121 User Manual

IE-iMcV-MultiWay

Operation Manual

FCC Radio Frequency Interference Statement

Class A (

using 48V Telco type power)

This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which the user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class A

limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A

prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

Class B (

using all other power options)

This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which the user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B

limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B

prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

Warranty

IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free from defects in materials
and workmanship under normal and proper use in accordance with IMC Networks' instructions and directions for a period of six (6) years after
the original date of purchase. This warranty is subject to the limitations set forth below.

At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such warranty period. This
limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable use, accident, negligence, service or
modification by anyone other than an authorized IMC Networks Service Technician or by any other causes unrelated to defective materials or
workmanship. Any replaced or repaired products or parts carry a ninety (90) day warranty or the remainder of the initial warranty period,
whichever is longer.

To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the warranty period. The
product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting product serial number and purchase date, a
written description of the defect and a Return Merchandise Authorization (RMA) number issued by IMC Networks. No products will be
accepted by IMC Networks which do not have an RMA number. For an RMA number, contact IMC Networks at PHONE: [phone] (in
the U.S and Canada) or [phone] or FAX: [phone]. The end-user shall return the defective product to IMC Networks, freight,
customs and handling charges prepaid. End-user agrees to accept all liability for loss of or damages to the returned product during shipment.
IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new product to the end-user, freight
prepaid, via method to be determined by IMC Networks. IMC Networks shall not be liable for any costs of procurement of substitute goods,
loss of profits, or any incidental, consequential, and/or special damages of any kind resulting from a breach of any applicable express or
implied warranty, breach of any obligation arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC
Networks product, whether or not IMC Networks has been advised of the possibility of such loss or damage.

EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES, WHETHER EXPRESS OR
IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT LIMITATION ANY SOFTWARE ASSOCIATED OR
INCLUDED. IMC NETWORKS SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY
OTHER PERSON, INCLUDING EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE INCONSISTENT
WITH THE WARRANTY SET FORTH ABOVE. ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE EXPRESS WARRANTY STATED ABOVE.

Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials accurately describe IMC
Networks product specifications and capabilities at the time of publication. However, because of ongoing improvements and updating of IMC
Networks products, IMC Networks cannot guarantee the accuracy of printed materials after the date of publication and disclaims liability for
changes, errors or omissions.

ii

Table of Contents

FCC Radio Frequency Interference Statement ........................................................... ii

Warranty................................................................................................................... ii

About the IE-iMcV-MultiWay ....................................................................................1

Operations, Administration and Maintenance (OAM) ............................................3

iView² Management Software ...................................................................................4

iView2 (iConfig view) .............................................................................................4

Installing an IE-iMcV-MultiWay .................................................................................5

DIP Switch Selectable Mode Configuration ...............................................................6

Mini-Serial Port ......................................................................................................... 7

LED Operation.......................................................................................................... 8

Autocross Feature for Twisted Pair Connections ....................................................8

Configuration ............................................................................................................ 8

Configuration Options...........................................................................................9

Basic Device Configuration Using the CLI............................................................10

Saved and Current Values ...............................................................................11

Command List ................................................................................................11

Assigning IP Information..................................................................................11

Password Protection for Serial Port Connections..............................................11

Assigning SNMP Trap Destinations ..................................................................12

Removing Trap Destinations............................................................................12

Creating Community Strings............................................................................12

Deleting Community Strings............................................................................13

Ending the Session ..........................................................................................13

Rebooting the Unit .........................................................................................13

Enabling/Disabling DHCP................................................................................13

Commands List (Space Bar) .................................................................................14

Cleandb..........................................................................................................15

Downloading Files ..........................................................................................15

Accounts.........................................................................................................16

VLAN Configuration........................................................................................16

Bandwidth (bw) ..............................................................................................19

Version ...........................................................................................................21

Viewing Port Statistics (ifstats) ..........................................................................22

Viewing Port RMON Statistics (rmstats)............................................................22

System Description (sysDescr) .........................................................................23

Reboot............................................................................................................23

(Operation and Administration Management) OAM ........................................23

Viewing SFP Statistics (sfpstats) ........................................................................24

Unit ................................................................................................................24

Port Configuration (port) .................................................................................25

iii

Using iView2........................................................................................................... 27

Unit Configuration ..........................................................................................28

Port Configuration...........................................................................................29

Bandwidth ......................................................................................................29

Tables .............................................................................................................30

VLAN..............................................................................................................31

Advanced .......................................................................................................32

OAM AH ........................................................................................................33

Loopback Testing ............................................................................................34

OAM CFM......................................................................................................36

Agent Info.......................................................................................................41

Connecting the IE-iMcV-MultiWay to an iMcV-Giga-FiberLinX-II.............................42

Configuration File Save/Restore Function.................................................................42

Saving a Configuration File to Disk: ......................................................................... 43

Uploading a Saved Configuration File through iView2 (iConfig view)........................45

SFP Ports................................................................................................................. 46

RJ-45 Data Port Pinout........................................................................................47

RS-232 Serial Console Port..................................................................................47

Product Applications ...............................................................................................48

Glossary ..................................................................................................................49

Troubleshooting ......................................................................................................51

Specifications .......................................................................................................... 52

IMC Networks Technical Support............................................................................52

Fiber Optic Cleaning Guidelines..............................................................................53

Electrostatic Discharge Precautions..........................................................................54

Safety Certifications................................................................................................. 55

iv

About the IE-iMcV-MultiWay

The IE-iMcV-MultiWay is an SNMP manageable modular device providing two fixed
10/100/1000Base-T copper ports and 2 SFP ports. The SFP ports support fiber or
copper SFPs. As a plug and play device, the IE-iMcV-MultiWay provides several
distinct modes of operation to support a wide range of applications. The IE-iMcV­MultiWay provides OAM functionality with 802.3ah (LINK-OAM ah) and 802.1ag
(SERVICE-OAM ag) supported on each port. It supports jumbo frame sizes of up to
10,240 bytes as well as AutoCross on the copper ports. As an Industrial Ethernet
device, it supports an extended temperature range of -40°C to +85°C. A console
port and a DIP Switch bay provide configuration options.

The IE-iMcV-MultiWay module is a single-wide module. It can be installed in the
following chassis:

• MediaChassis series

• IE-MediaChassis series

• iMediaChassis series

The IE-iMcV-MultiWay requires two small form-factor (SFP) modules which provide
greater flexibility in the network environment. The hot-swappable nature of the SFPs,
available in dual strand for Multi Mode and Single Mode, and single strand fiber types
for Single Mode, allow for easy configuration and future upgrading as network
demands evolve. The SFP modules must be MSA-compliant and both DDMI and
non-DDMI are supported. The fiber SFP can support 100Mbps or 1000Mbps; while
the copper SFPs support 10/100/1000Mbps and 1000Mbps.

SFPs are sold separately by IMC Networks and meet Class 1 Laser Safety Standard.

IE-iMcV-MultiWay Features and Configuration

The IE-iMcV-MultiWay offers a full feature set including Auto Negotiation, Selective
Advertising, AutoCross, VLANs, SNMP management, loopback testing and OAM. Unit

2

software updates can be downloaded through TFTP or iView

(iConfig view).

IE-iMcV-MultiWay features include:

• SNMP manageable

• OAM AH

o

IEEE 802.3ah Link OAM for per port monitoring (OAM AH)

1

• OAM AH Functions

o

Discovery

o

Link Performance Monitoring

o

Remote Loopback

o

Fault Detection

o

Link Fault

o

Dying Gasp

o

Critical Event

• OAM CFM (SERVICE-OAM)

o

IEEE 802.1ag Connectivity Fault Management (OAM CFM)

o

OAM CFM Functions

o

Continuity Check

o

Loopback

• Speed/duplex modes

• 802.1q VLAN

• Extra tagging with user-defined VLAN tag Ethertype

• Ethertype 88A8 as defined in 802.1ad

• Command Line Interface capable (CLI)

• Telnet

• Password assignment via CLI, Telnet or iView²

• DIP Switch configuration for Modes

• Bandwidth Limiting

The IE-iMcV-MultiWay can be installed as a standalone CPE device, back to back, or
as a Remote when connected to an iMcV-Giga-FiberLinX-II configured as a Host.

As a CPE device, the IE-iMcV-MultiWay can behave as a remote to an iMcV-Giga­FiberLinX-II host when:

1) The iMcV-Giga-FiberLinX-II:

• Is connected via the SFP ports on the IE-iMcV-MultiWay

• Is configured as a Host

• Uses firmware version A1 860-00D1 or higher

2) The SNMP card (if present):

• Uses SNMP firmware version 953-00D0 or higher

3) The IE-iMcV-MultiWay:

• Uses firmware version 123-00A1 or higher

2

When using iView

, the IE-iMcV-MultiWay can be fully managed without an IP
address using a secure management channel. However, an IP address can be
assigned through iView2 (iConfig view), the CLI or Telnet using the default IP address
of 10.10.10.10.

2

Operations, Administration and Maintenance (OAM)

OAM is a general term used in network management and is typically applied to a
series of standard protocols for installing, monitoring, and troubleshooting
Metropolitan Area Networks.

When applied to Ethernet – OAM is typically assumed to refer to the layer 2 (MAC
layer), management protocols, specifically 802.3ah and 802.1ag. Layer 2
management protocols do not need higher level transport protocols to operate, OAM
data is transferred in standard multicast Ethernet frames.

802.3ah OAM:

(LINK-OAM)

802.1ag:

(SERVICE-OAM)

Is a point-to-point protocol designed to verify a specific link
between two directly connected devices (over copper or fiber),
which support 802.3ah OAM. One device must be configured
to be an active OAM device, the other a passive (typically the
core switch would be the active device, the end device passive).

802.3ah OAM provides link status, remote fault detection and
the ability to initiate a loopback circuit.

Often referred to as Connectivity Fault Management (CFM), is an
end-to-end protocol designed to verify a specific network path
between two devices that may well be in different geographical
locations. CFM allows the network operator to administer,
monitor and debug the network using continuity check (a heart
beat message), link trace (similar to traceroot, but operating at
the MAC layer) and finally loopback (can be likened to a layer 2
ping).

3

iView² Management Software

iView² is the IMC Networks management software that features a Graphical User
Interface (GUI) and gives network managers the ability to monitor and control the
manageable IMC Networks products.

iView² is available in several versions, including a WebServer version 3.0, and can
also function as a snap-in module for HP OpenView Network Node Manager and
other third party SNMP Management software. For assistance in selecting the right
version of iView² for a specific operating system, please visit:

http://www.imcnetworks.com/products/iview2.cfm

2

iView

supports the following platforms:

• Windows 2000

• Windows XP

• Windows Vista

• Windows 7

Please see the SNMP Management Module manual for software configuration
options.

iView2 (iConfig view)

iView2 (iConfig view) is an in-band utility created by IMC Networks, used for SNMP
configuration for IMC Networks’ SNMP-manageable devices.

2

The iView

(iConfig view) feature allows the following to be performed:

• Set an IP address, subnet mask and default gateway

• Define community strings and SNMP Traps

2

iView

(iConfig view) also includes an authorized IP address system and restricted
access to MIB groups which are supported by IMC Networks’ manageable devices.
These extra layers of security do not affect SNMP compatibility. iView

2

(iConfig view)
can upload new versions of the system software and new MIB information. It also
includes diagnostic capabilities for faster resolution of technical support issues.

4

Installing an IE-iMcV-MultiWay

IE-iMcV-MultiWay can be installed in IMC networks’ unmanaged MediaChassis, IE­MediaChassis series, or the iMediaChassis series.

To install an IE-iMcV-MultiWay

Remove the blank bracket covering the slot where the module is to be

1.
installed by removing the screws on the outside edges of the bracket.

Slide the iMcV-Modules into the chassis, via the cardguides, until the

2.
module is seated securely in the connector.

Secure the module to the chassis by tightening the captive screws.

3.

Save any “blanks” removed during installation for future use if the

4.
configuration requirements change.

5

DIP Switch Selectable Mode Configuration

The IE-iMcV-MultiWay can be configured in one of the following ways via DIP Switch
settings (see page

Error! Bookmark not defined.

):

Configuration

Method

4-Port Switch
(default)

Dual
Converter
mode

1+1 SFP
Protection
Non-Revertive
mode

Description

In this mode, the unit acts as a standard 4-port MAC-layer switch.

In this mode, the unit functions as two independent (SFP to TX)
media converters and traffic never passes between the two
converters.

In this mode, the "SFP A" port (fiber or copper) is connected
through the switch to the drop ports as the main link. The "SFP B"
port (fiber or copper) is active into the MAC switch, but no
connection inside the switch is made; in this way, the "SFP B" line
is held as the standby line. The "SFP B" line is held in the LINK
state for testing and line verification, but does not actively carry
user data.

When a fault is detected on the active line, all customer traffic is
switched to the “SFP B” port. With non-Revertive mode data is
not resumed by “SFP A” port until SFP B fails or is disconnected.

1+1 SFP
Protection
Revertive
mode

In this mode, the "SFP A" port (fiber or copper) is connected
through the switch to the drop ports as the main link. The "SFP B"
port (fiber or copper) is active into the MAC switch, but no
connection inside the switch is made; in this way, the "SFP B" line
is held as the standby line. The "SFP B" line is held in the LINK
state for testing and line verification, but does not actively carry
user data.

When a fault is detected on the active line, all customer traffic is
switched to the “SFP B” port. Once the “A” port is no longer in a
fault condition, data is resumed on that port.

NOTE

Revertive and Non-Revertive modes can only operate on the ports with SFPs, not the fixed
copper ports.

6

DIP

Switch

1 Dual Enable dual channel OFF
2 1+1 Provides 1+1 protection with non-revertive switching OFF
3 1+1 Revert Provides 1+1 protection with revertive switching OFF
4 LoSpd B Force SFP "B" for low-speed operation OFF
5 LoSpd A Force SFP "A" for low-speed operation OFF
6 Reserved

Name Description Default

Setting

Mini-Serial Port

A console port, located at the top of the faceplate, allows the customer to use a local
RS-232 serial interface for management. A special mini-jack to DB9-F cable is
provided with the product for direct connection to a PC serial port.

NOTE

To log on through the serial port, set the computer/terminal for VT-100 emulation,
with: 38.4K baud, 8 data bits, 1 stop bit, no parity, no FlowControl.

7

LED Operation

Each IE-iMcV-MultiWay includes SFP and RJ-45 LEDs.

(TX 1, TX 2)

LNK/ACT

FDX

SFP A, SFP B

OAM

ACTIVE

LNK

FLT

Glows green when a link is established on the TX
port; blinks green when activity is detected on the TX
port.

Glows yellow when a link is established on the TX
port; blinks green when activity is detected on the TX
port.

Glows green when an active OAM AH channel is
established.

Serial Port

Glows green when the port is active
OFF when SFP is in standby (does not indicate

activity)

Glows green with a valid optical link.

Glows amber when a fault is detected.

Autocross Feature for Twisted Pair Connections

All fixed twisted pair ports on the IE-iMcV-MultiWay include AutoCross, a feature that
automatically selects between a crossover workstation and a straight-through
connection depending on the connected device.

Configuration

The IE-iMcV-MultiWay includes many features that are configurable via a
serial/Telnet session (CLI) or through iView² (SNMP Management view or iConfig
view).

8

Configuration Options

The following options are configurable through both the iView2 (iConfig view) and
Serial/Telnet.

Feature iView² Serial/Telnet

9

Loopback
Auto Negotiation
Force Mode
FlowControl
VLANs
IP Address
Subnet Mask
Default Gateway
MIB Community
Traps Assignment
Users
Passwords
Access Level
Reboot
Frame size selection
Bandwidth Limiting

9
9
9
9
9
9
9
9
9
9
9
9
9
9
9

9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9

The following table presents management options configurable via iView2 (iConfig
view) or a serial/Telnet session.

9
9

9
9

2

Serial/Telnet

9

9

9

9

Feature iView

(iConfig)

PROM Software Download/Upload
Telnet Session
Software Download Setup (TFTP)
DHCP
Restore Configuration
Save Configuration

9

Basic Device Configuration Using the CLI

After running through an initial self test, the screen will display the following message:

Enter

Press

for Device Configuration.

Enter

Press

to open the main configuration screen. This screen allows the user to set
the IP address and the destination IP address for traps with the community string,
read/write access and password as usual.

Saved Values. (These values will be active after reboot)
IP Address - 10.10.10.10

Subnet Mask - 255.255.255.0 DHCP is Not Active
Default Gateway - 0.0.0.0

Current Values. (These values are in use now)
IP Address - 10.10.10.10
Subnet Mask - 255.255.255.0
Default Gateway - 0.0.0.0

Community String: public Access: r/w
Press I to enter new saved parameter values. Press P to change Password.

Press T to enter new Trap Destination. Press K to remove All Trap Destinations.
Press C to enter new Community String. Press U to remove All Community Strings.
Press E to End session. Type REBOOT to reboot unit. Press D for DHCP On/Off.
Press SpaceBar for additional commands.

10

This screen contains the following information and options:

Saved and Current Values

Saved values display the changes made during the current session and current values
display the values currently in use:

IP Address (IP address of SNMP agent)

•

•

Subnet Mask (mask to define IP subnet to which agent is connected)
Default Gateway (default router for IP traffic outside of the subnet)

•

Command List

I

= Enter new

P

= Change the

T

= Enter new

K

= Remove

C

= Create

U

= Delete All

E

=

End

the session*

Reboot
D

= Reboot the unit (may result in short data loss)

= Enable or disable

Space Bar

Saved Parameter Values

Password

*

Trap Destinations

All Trap Destinations

SNMP Community Strings

SNMP Community Strings

DHCP

= Opens the device specific configuration options screen.

*

The screens illustrated in this manual show capabilities for users with Admin
rights. Individuals with User-level rights can only view port status and port
settings, change their password, end a session, and reboot the unit.

NOTE

It is necessary to reboot the IEiMcV--MultiWay after making any modifications to the Saved
Values for the changes to take effect. To reboot, type
Configuration screen.

Reboot

at the prompt on the Main

Assigning IP Information

To modify the Saved Parameter Values (i.e., assign IP address and subnet mask),
press

I

. The system prompts for the IP address and subnet mask for the connected

Enter

device. Press

Enter

to skip. When finished, press

after each entry. A default gateway can also be assigned, or press

Enter

, then type

reboot

for changes to take
effect. The Current Values can only be saved and acted on after the IE-iMcV­MultiWay has been successfully rebooted.

Password Protection for Serial Port Connections

Password/username is not offered for the serial port by default. This allows the end
user to quickly access the device for some basic configuration capability. Password
protection is provided for the serial configuration process by pressing

P

on the main

configuration screen. Enter a password, keeping in mind that passwords are case-

11

sensitive and must not exceed eight characters or include spaces, and press

Enter

.
This password will be requested whenever logging on. To remove password
protection, select

P

and, instead of entering a password, press

Enter

.

Passwords have the following requirements:

The password must be between 1 and 8 characters long

•

The password consists of a combination of any ASCII characters except spaces

•

Passwords are case sensitive

•

Passwords are a way to make the management of the IMC Networks devices secure,
but these password lists must be stored and maintained.

Assigning SNMP Trap Destinations

Traps are sent by the manageable device to a management PC when a certain event
takes place. To enter a trap destination, press

T

. When prompted, enter a New IP

Address prompt, enter the appropriate IP address of the destination device and press

Enter

. Then, type the name of the community string (that the destination device has

been configured to accept) and press

Enter

version 1 or 2c and press

. This function enables ALL of the device traps.

Supported traps include: Link Down, Link Up, and Last Gasp.

Enter

. Select whether the trap is for SNMP

Removing Trap Destinations

To remove all trap destinations, press K. Press Y to continue to confirm or N to abort

Enter

and remove all trap destinations. Press

to finish.

This function will delete all trap destinations. To selectively delete trap
destinations or to disable/enable Traps, use iView

2

(iConfig view) to configure

the device.

Creating Community Strings

Community strings add a level of security to a network. The default community string
is named "public" and has read/write access. For security, "public" should be replaced
with custom community strings such as ones created with read-only access (for
general use), and another with read/write access (for the administrator).

C

To create a new community string, go to the main configuration screen and press

.

Enter the name of the new community (up to 16 characters, no spaces) and press

Enter

. Then type one of the following to assign the community string’s access rights:

R

•

•

•

= read-only access

W

= read/write access

Enter

= abort

After entering

R

or W, press

Enter

. To finish, press

12

Enter

and reboot.

Deleting Community Strings

To delete all community strings, perform the following:

Press

U

. The "Are you sure you want to delete all future strings?" prompt is displayed.

Y

Press
Press

when prompted to proceed and delete all community strings, N to abort.

Enter

to finish.

This function will delete ALL community strings. To selectively delete community

2

strings, use iView

(iConfig view) to configure the device.

Ending the Session

Press E to end a serial port or Telnet/HyperTerminal session before disconnecting the
serial cable. This will stop the continuous stream of data to the serial port.

Rebooting the Unit

To reboot the IE-iMcV-MultiWay, type

reboot

from the main screen or the command

menu.

Enabling/Disabling DHCP

To toggle DHCP on the IE-iMcV-MultiWay between enable and disable, press D and
then

Y.

Press the

Space Bar

once to return to the main screen without making any

changes.

DHCP Disable

(Static IP Addressing)

DHCP is disabled in the default configuration. Initially, modules are assigned a Static
default IP Address of 10.10.10.10. Changes to the Static IP Address can be added

2

manually through iView

(iConfig view) or a Console session. The changes will be

initiated following reboot of the module.

DHCP Enable

(Dynamic IP Addressing)

If a DHCP server is present on the network and DHCP is enabled, the DHCP client
will initiate a dialogue with the server during the boot up sequence. The server will
then issue an IP address to the management card. Once the new IP address is
received, the SNMP Management Module will reboot so that the new IP address will
take effect. Refer to About Serial Port Configuration for more information about
Enabling/Disabling DHCP.

When there is no DHCP server on the network, use the serial configuration to
manually set the IP addresses.

When DHCP is enabled, the IP address (default 10.10.10.10 or a previously used IP
address, or user-configured) is saved. When DHCP is disabled, the saved IP address
will be reinstated and the device will reboot.

DHCP servers give out lease times: devices renew their leases based on the
administrator-specified time. If a device cannot renew its lease, and the lease
expires, the device will be given the IP address 10.10.10.10 and will reboot.

13

Commands List (Space Bar)

The IE-iMcV-MultiWay also includes several device-specific options. To access these
options, press the

Space Bar

the action to be performed (as shown below) and press

from the Main Configuration screen, type the name of

Enter

.

Command Description

cleandb

download

accounts

vlan

bw

version

ifstats

rmstats

sysDescr

reboot

Reboots the unit with a clean database. This removes all information from
the database and sets the unit to factory defaults.

Downloads firmware via the TFTP protocol

Allows the addition for User, Superuser, Admin

Provides selection of two modes of operation to support all VLAN
configurations.

Displays settings for Bandwidth configuration

Displays the unit’s firmware and hardware version

Displays interface statistics

Displays remote monitoring (RMON) statistics on packets received as defined
in RFC 2819 for RMON.

Allows the editing of sysName, sysDescr, and Port information

Allows a soft reboot of the unit after changes are made by the end user

oam

sfpstats

Enable/disable OAM

Provides information about the wavelength, serial number, output power,

14