B&B Electronics 855-11844-51 User Manual

McBasic-Gigabit

Operation Manual

International Headquarters

B&B Electronics

707 Dayton Road

Ottawa, IL 61350 USA

Phone [phone] — General Fax [phone]

Email: [e-mail]

Website: www.bb-elec.com

European Headquarters

B&B Electronics

Westlink Commercial Park

Oranmore, Co. Galway, Ireland

Phone [phone] — Fax [phone]S5

Email: [e-mail]

Website: www.bb-elec.com

© 2013 B&B Electronics. All rights reserved.

The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any
errors that may appear in this document. McBasic-Gigabit is a trademark of B&B Electronics. Other brands or product
names may be trademarks and are the property of their respective companies.

Document Number 55-80913-01 A4 October 2013

FCC Radio Frequency Interference Statement

Safety Certifications

This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which the user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class A

limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A

prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

Limited Lifetime Warranty

Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable
solely to the original user and is not transferable.

This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.

Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:

1. Replace the product with a functional equivalent;

2. Repair the product; or

3. Provide a partial refund of purchase price based on a depreciated value.

Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.

Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any other
liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third party
except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the products,
including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have
been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions, illustrations, figures
as to performance, drawings and particulars of weights and dimensions contained in the B&B Electronics’ catalogs, price
lists, marketing materials or elsewhere since they are merely intended to represent a general idea of the products and do
not form part of this price quote and do not constitute a warranty of any kind, whether express or implied, as to any of the
B&B Electronics’ products.

THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED
IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE
INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE LIABLE FOR
LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL
DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY
OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF
B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.

UL/CUL: Listed to Safety of Information Technology Equipment, including

Electrical Business Equipment.

CE: The products described herein comply with the Council Directive on

Electromagnetic Compatibility (2004/108/EC) and the Council Directive
on Electrical Equipment Designed for use within Certain Voltage Limits
(2006/95/EC). Certified to Safety of Information Technology
Equipment, Including Electrical Business Equipment. For further
details, contact B&B Electronics.

Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1

European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.

ii

12

Fiber Optic Cleaning Guidelines

Table of Contents

Fiber Optic transmitters and receivers are extremely susceptible to contamination by
particles of dirt or dust, which can obstruct the optic path and cause performance
degradation. Good system performance requires clean optics and connector ferrules.

1.

Use fiber patch cords (or connectors, if you terminate your own fiber) only from
a reputable supplier; low-quality components can cause many hard-to-diagnose
problems in an installation.

2.

Dust caps are installed at B&B Electronics to ensure factory-clean optical devices.
These protective caps should not be removed until the moment of connecting
the fiber cable to the device. Should it be necessary to disconnect the fiber
device, reinstall the protective dust caps.

3.

Store spare caps in a dust-free environment such as a sealed plastic bag or box so
that when reinstalled they do not introduce any contamination to the optics.

4.

If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to remove
particles of dirt.

Electrostatic Discharge Precautions

Electrostatic discharge (ESD) can cause damage to any product, add-in modules or
stand alone units, containing electronic components. Always observe the following
precautions when installing or handling these kinds of products

1.

Do not remove unit from its protective packaging until ready to install.

FCC Radio Frequency Interference Statement .................................................... ii

Limited Lifetime Warranty .................................................................................. ii

About the McBasic-Gigabit ................................................................................. 1

Installing a McBasic-Gigabit ................................................................................ 1

Configuration Instructions .................................................................................. 2

LinkLoss, FiberAlert and Link Fault Pass-Through ................................................ 3

Additional Gigabit Features ................................................................................ 6

LED Operation ................................................................................................... 7

Troubleshooting ................................................................................................. 8

Specifications ..................................................................................................... 9

B&B Electronics Technical Support ................................................................... 10

Fiber Optic Cleaning Guidelines ....................................................................... 11

Electrostatic Discharge Precautions ................................................................... 11

Safety Certifications .......................................................................................... 12

2.

Wear an ESD wrist grounding strap before handling any module or component.
If the wrist strap is not available, maintain grounded contact with the system unit
throughout any procedure requiring ESD protection.

3.

Hold the units by the edges; do not touch the electronic components or gold
connectors.

4.

After removal, always place the boards on a grounded, static-free surface, ESD
pad or in a proper ESD bag. Do not slide the modules or stand alone units over
any surface.

WARNING!

extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.

Integrated circuits and fiber optic components are

11

iii