B&B Electronics 850-18510 Datasheet

Work

Media Conversion

iMcV Series Modules

10 Mbps, 100 Mbps, 10/100 Auto Negotiating and Standard and

Extended Temperature (IE) 1000 Mbps Ethernet SNMP-Manageable Media Converters

Monitor and control all connections from a central site with iMcV Series
SNMP-manageable media conversion modules.

Features and Benefits

Meets a variety of installation
requirements

• Available for multi-mode or single-mode
fiber

• Double fiber capacity with single-strand
fiber versions

• ST, SC or SFP (LC) connector

• iMcV-Gigabit TX/SFP is compatible with
IMC Networks’ SFPs and all standard
MSA compliant SFP transceivers

Easy to configure and manage with
GUI-based iView

• Monitor links and receive vital traffic and
health information and notification should
problems occur

Maximizes network uptime

• Modular, hot-swappable architecture reduces
operational costs associated with product
installation, upgrades and maintenance

Eases Troubleshooting

• LinkLoss and FiberAlert features, plus SNMP
management and LEDs assist in diagnosing
problems on fiber optic networks

• Features Link Fault Pass-Through (LFPT),
a troubleshooting feature that monitors the
copper and fiber ports of the unit;
if a port loses LINK, the unit disables
the transmitting signal on the other port
(Pass-Through) and notifies the user via
LED (available on iMcV-LIM [100],
iMcV-Gigabit and IE-iMcV-Gigabit)

• Supports Config Control, a feature that
retains the latest configuration on a module
regardless of how the initial configuration
was setup; whether by DIP Switch or SNMP
Management Module (available on iMcV-LIM
[100] & iMcV-Gigabit)

The iMcV series includes:

• iMcV-PIM converts copper to fiber at

a data rate of 10 Mbps

• iMcV-LIM converts copper to fiber at
a data rate of 100 Mbps

• iMcV-LIM 10/100 converts 10 Mbps
copper to 10 Mbps fiber OR converts
100 Mbps copper to 100 Mbps fiber

• iMcV-Gigabit converts copper to fiber
at a data rate of 1Gbps

• IE-iMcV-Gigabit TX/SFP converts copper
to fiber (via SFP transceiver) at a data rate
of 1 Gbps

Satisfying today’s networking needs while preparing for tomorrow ’s
requirements in cabling bandwidth, distance and security can
make designing and installing the physical layer of networks a
daunting task. The decreasing cost of fiber optic cabling and
switching equipment makes all-optical LANs the obvious choice
when future-proofing a network. Replacing legacy equipment and
the wiring infrastructure is a costly choice that could produce too
much network downtime. Managed media conversion allows the
implementation of new technologies on an existing network and
the monitoring of all connections to keep networks up-to-date and
running in peak condition.

Easily configure and manage converters with the GUI-based iView².
As an SNMP management application, iView² gives network
managers the ability to monitor and control IMC Networks'
products. iView² runs standalone on Windows NT/XP/2000, as
a standalone Java Application for other operating systems, as a
snap-in module for HP OpenView, as a Web Server running under
IIS or as a Java Web Servlet. For assistance in selecting the right
version of iView² for your operating system, visit our web site at:
http://www.imcnetworks.com/Products/iView2.cfm

Application Example

These iMcV series modules make the critical connection
between twisted pair and fiber optics. Most are also
available in a single-strand fiber version which allows two
wavelengths to share one fiber strand — Full-Duplex data
travels on different wavelengths (1310 nm and 1550 nm,
for example)— doubling the capacity of fiber. Deploy
single-strand fiber products in pairs, or connect two
compatible IMC Networks single-strand fiber products.

* SFPs sold separately

RoHS Compliant

www.imcnetworks.com

800-624-1070

Making Your Net

Better — Since 1988

Technical Specifications

iMcV-PIM

• 10Base-T twisted pair

• 10Base-FL fiber

• MDI/MDIX switch

• Features LinkLoss and
FiberAlert

iMcV-LIM (100)

• 100Base-TX twisted pair

• 100Base-FX or SX fiber

• AutoCross for MDI/MDIX

• Features LinkLoss, FiberAlert
& Auto Negotiation

• Features Link Fault
Pass-Through (LFPT)

• Supports Config Control

iMcV-LIM (10/100)

• 10Base-T twisted pair

• 10Base-FL fiber

• 100Base-TX twisted pair

• 100Base-FX or SX fiber

• MDI/MDIX switch

• Features Link Fault Detection
and Transparency

• Features Auto Negotiation

iMcV-Gigabit

• 1000Base-T twisted pair

• 1000Base-LX or SX fiber

• AutoCross for MDI/MDIX

• Features FiberAlert, LinkLoss
& Link Fault Pass-Through

• Supports Config Control

IE-iMcV-Gigabit TX/SFP

• 1000Base-T twisted pair

• IE-SFP 1250 Mbps/1.25 Gbps

• AutoCross for MDI/MDIX

• Features FiberAlert, LinkLoss
& Link Fault Pass-Through

• Supports Config Control

All Modules

• Connectors: RJ-45 and ST, SC or SFP

• 50/125µm or 62.5/125µm multi-mode fiber

• 9/125µm single-mode fiber

• Install in any iMediaChassis or MediaChassis

• Support GUI-Based iView²

• Support Half- and Full-Duplex operation

• Include diagnostic LEDs

• Include hot-swappable architecture

Shipping Weight:

0.30 lbs (.11 kg)

Regulatory Approvals:

• FCC Class A

• FCC Class B (iMcV-LIM [100])

• CE

Operating Temperature:

+32° to +122° F (0° to +50° C);

-40° to +185° F (-40° to +85° C) IE-iMcV-Gigabit;
5% to 95% (non-condensing), 0 – 10,000 ft. altitude

Storage Temperature:

-13° to +158° F (-25° to +70° C);
5% to 95% (non-condensing)

Fiber Optics Specifications

For each product listed below in the Ordering Information section, the DISTANCE represents an approximate fiber distance based on industry-standard
fiber attenuation specifications. Actual distances will vary for each installation. For complete power budgets and information on calculating specific
distances, visit www.imcnetworks.com/go/fcs or contact IMC Networks Fiber Consulting Services at 949-465-3000.

Ordering Information

PART NUMBER DESCRIPTION DISTANCE

iMcV-PIM 10 Mbps Modules

850-14940 TP/FO-MM850-ST 2 km

850-14941 TP/FO-MM850-SC 2 km

850-14942 TP/FO-MM1300-ST 2 km

850-14943 TP/FO-MM1300-SC 2 km

850-14944 TP/FO-SM1310/PLUS-ST 40 km

850-14945 TP/FO-SM1310/PLUS-SC 40 km

850-14946 TP/FO-SM1310/LONG-ST 40 km

850-14947 TP/FO-SM1310/LONG-SC 40 km

850-14949 TP/FO-SM1550/LONG-SC 80 km

PART NUMBER DESCRIPTION DISTANCE

iMcV-LIM 100 Mbps Modules

850-15611 TX/FX-MM850-ST 2 km

850-15612 TX/FX-MM850-SC 2 km

850-15613 TX/FX-MM1300-ST 5 km

850-15614 TX/FX-MM1300-SC 5 km

850-15617 TX/FX-SM1310/PLUS-ST 40 km

850-15618 TX/FX-SM1310/PLUS-SC 40 km

850-15619 TX/FX-SM1310/LONG-ST 80 km

850-15620 TX/FX-SM1310/LONG-SC 80 km

850-15622 TX/FX-SM1550/LONG-SC 80 km

850-15623 TX/FX-SM1550/XLONG-SC 100 km

¥

iMcV-LIM 100 Mbps Modules Single-Strand Fiber Modules *

850-15631 TX/SSFX-MM1310-SC (1550 rcv) 2 km

850-15632 TX/SSFX-MM1550-SC (1310 rcv) 2 km

850-15633 TX/SSFX-SM1310-SC (1550 rcv) 20 km

850-15634 TX/SSFX-SM1550-SC (1310 rcv) 20 km

850-15635 TX/SSFX-SM1310/PLUS-SC (1550 rcv) 40 km

850-15636 TX/SSFX-SM1550/PLUS-SC (1310 rcv) 40 km

850-15637 TX/SSFX-SM1310/LONG-SC (1550 rcv) 60 km

850-15638 TX/SSFX-SM1550/LONG-SC (1310 rcv) 60 km

* These products have single-strand fiber technology.

For more information go to: www.imcnetworks.com/products/SSFX.cfm

§

SFP modules are sold separately. For more information on compatible IMC Networks SFPs,

go to: www.imcnetworks.com/Products/product.cfm?family=32

¥

CWDM wavelengths are also available. Contact IMC Networks for a complete list of part numbers.

PART NUMBER DESCRIPTION DISTANCE

iMcV-LIM 10/100 Mbps Modules

850-14260 10/100-MM850-ST 2 km

850-14261 10/100-MM850-SC 2 km

850-14262 10/100-MM1300-ST 5 km

850-14263 10/100-MM1300-SC 5 km

850-14267 10/100-SM1310/PLUS-ST 40 km

850-14268 10/100-SM1310/PLUS-SC 40 km

850-14269 10/100-SM1310/LONG-ST 80 km

850-14270 10/100-SM1310/LONG-SC 80 km

850-14274 10/100-SM1550/LONG-SC 80 km

iMcV-LIM 10/100 Mbps Modules Single-Strand Fiber Modules *

850-14240 10/100-SSFX-MM1310-SC (1550 rcv) 2 km

850-14243 10/100-SSFX-MM1550-SC (1310 rcv) 2 km

850-14244 10/100-SSFX-SM1310-SC (1550 rcv) 20 km

850-14245 10/100-SSFX-SM1550-SC (1310 rcv) 20 km

850-14246 10/100-SSFX-SM1310/PLUS-SC (1550 rcv) 40 km

850-14247 10/100-SSFX-SM1550/PLUS-SC (1310 rcv) 40 km

850-14248 10/100-SSFX-SM1310/LONG-SC (1550 rcv) 60 km

850-14249 10/100-SSFX-SM1550/LONG-SC (1310 rcv) 60 km

PART NUMBER DESCRIPTION DISTANCE

IE-iMcV-Gigabit 1000 Mbps Modules

850-18510 850-18912^IE-iMcV-Gigabit, TX/SFP

iMcV-Gigabit 1000 Mbps Modules

¥

850-15511 850-11913^TX/SX-MM850-SC 220/550 m

850-15512 850-11914^TX/LX-SM1310-SC 10 km

850-15513 850-11915^TX/LX-SM1310/PLUS-SC 40 km

850-15514 850-11917^TX/LX-SM1550/LONG-SC 80 km

850-15515 850-11918^TX/LX-SM1550/XLONG-SC 100 km

iMcV-Gigabit 1000 Mbps Module Single-Strand Fiber *

^

850-15521 850-11834

850-15522 850-11835

850-15523 850-11836

850-15524 850-11837

850-15525 850-11844

850-15526 850-11845

850-15527 850-11846

850-15528 850-11847

850-15529 850-11848

850-15530 850-11849

^

Designates modules that DO NOT support Configuration Control or Link Fault Pass-Through.

TX/SSLX-SM1310-SC (1550 rcv)

^

TX/SSLX-SM1550-SC (1310 rcv)

^

TX/SSLX-SM1310-SC (1490 rcv)

^

TX/SSLX-SM1490-SC (1310 rcv)

^

TX/SSLX-SM1310/PLUS-SC (1550 rcv)

^

TX/SSLX-SM1550/PLUS-SC (1310 rcv)

^

TX/SSLX-SM1310/PLUS-SC (1490 rcv)

^

TX/SSLX-SM1490/PLUS-SC (1310 rcv)

^

TX/SSLX-SM1310/LONG-SC (1550 rcv)

^

TX/SSLX-SM1550/LONG-SC (1310 rcv)

§

Varies

10 km

10 km

10 km

10 km

40 km

40 km

30 km

30 km

70 km

70 km

IMC Networks

Headquarters

19772 Pauling
Foothill Ranch, CA 92610
TEL: [phone]
FAX: [phone]
[e-mail]

IMC Networks

Europe

Herseltsesteenweg 268
B-3200 Aarschot, Belgium
TEL: [phone]
FAX: [phone]
[e-mail]

IMC Networks

Eastern US/Latin America

28050 U.S. Hwy. 19 North, Suite 306
Clearwater, FL 33761
TEL: [phone]
FAX: [phone]
[e-mail]

IMC Networks

Fiber Consulting Services

For information call:
TEL: [phone]
1-800-624-1070 (US/CAN)
[phone] (Europe)
[e-mail]

Copyright © 2012 IMC Networks. All rights reser ved.
The information in this docum ent is s ubject to
change without notice. IMC Networks assumes
no responsibility for any errors that may appear in
this document. Specific product names may be
trademarks or registered trademarks and are the
property of their respective companies.

DS-iMcV-Modules-1204