B&B Electronics 849-10100 User Manual

iMcV-WDM/2
Operation Manual
LIMITED LIFETIME WARRANTY
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any other liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third party except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the products, including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions, illustrations, figures as to performance, drawings and particulars of weights and dimensions contained in the B&B Electronics’ catalogs, price lists, marketing materials or elsewhere since they are merely intended to represent a general idea of the products and do not form part of this price quote and do not constitute a warranty of any kind, whether express or implied, as to any of the B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED, INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE LIABLE FOR LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.
ii
Table of Contents
Limited Lifetime Warranty ........................................
About the iMcV-WDM/2 ...................................................................................................... 1
Installing the iMcV-WDM/2 ................................................................................................. 1
Connecting the iMcV-WDM/2 ............................................................................................ 1
Specifications ............................................................................................................................ 2
B&B Electronics Technical Support ................................................................................... 3
Fiber Optic Cleaning Guidelines ........................................................................................ 4
Electrostatic Discharge Precautions .................................................................................. 5
Certifications ............................................................................................................................. 6
Error! Bookmark not defined.
iii
About the iMcV-WDM/2
The iMcV-WDM/2 module is a passive two-channel protocol and speed independent Wave Division Multiplexer which allows two individual wavelengths to share one fiber — Full-Duplex data travels on 1310nm and 1550nm — virtually doubling the capacity of the installed fiber. Suited for installations where fiber is limited in terms of availability and/or distance, service providers and network managers can easily double their fiber capacity without incurring the costs associated with installing new fiber.
As a protocol independent device supporting all popular communication protocols, the iMcV-WDM/2 module helps service providers and network managers simplify network administration. Enterprise and campus area network administrators can, for example, deploy the iMcV-WDM/2 solution to combine both voice and data traffic over the same duplex fiber between related facilities.
Installing the iMcV-WDM/2
The iMcV-WDM/2 may be installed in any B&B Electronics iMediaChassis series chassis or into a MediaChassis series.
1.
Remove the blank brackets covering the slots where the module is to be installed, if present, by removing the screws on the outside edges of the bracket.
2.
Slide the module into the chassis, via the card guides, until the module is seated securely in the connector. Secure the module to the chassis by tightening the captive screws. Save any
3. “blanks” removed during installation for future use should your configuration requirements change.
Connecting the iMcV-WDM/2
iMcV-WDM/2 takes two devices of differing wavelengths, transmits the wavelengths along a single strand of fiber, then separates the wavelengths, enabling the fiber optic receivers to receive a signal of the correct wavelength.
When connecting devices to the iMcV-WDM/2, make sure that:
 the wavelengths of each device connected to iMcV-WDM/2 correspond to
each other and iMcV-WDM/2 and that
 the fiber transmitters are connected to the fiber receivers.
NOTE
This product has a minimum isolation factor of 17db. This means the difference in
1
launch power between any two inputs to the product should not exceed 17db. In an application where the isolation factor might exceed 17db, it is recommended that attentuators be used, in series, with relationship to the stronger input.
The diagram below illustrates the route that data will take according to the above guidelines. Another path in the opposite direction is needed to complete this installation.
Specifications
Environmental
Operating Temperature
32° - 104° F (0° - 40° C)
Storage Temperature
0° - 160° F (-20° - 70° C)
Humidity
5 - 95% (non-condensing)
Fiber Optic Specifications
Insertion Loss: 1.4dB @ 1550 nm, 1.5 dB @ 1300 nm (Max values)
2
B&B Electronics Technical Support
Tel:
Monday-Friday, 7:00am-7”00pm CST
+353 91 792444 (Europe)
Monday through Friday 8:00am - 5:00pm GMT
Fax:
E-Mail:
Web:
(800) 346-3119 (in the U.S. and Canada)
(815) 433-5109
support@bb-elec.com
www.bb-elec.com
3
Fiber Optic Cleaning Guidelines
Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules.
Use fiber patch cords (or connectors, if you terminate your own fiber) only
1. from a reputable supplier; low-quality components can cause many hard-to­diagnose problems in an installation.
2.
Dust caps are installed at B&B Electronics to ensure factory-clean optical devices. These protective caps should not be removed until the moment of connecting the fiber cable to the device. Should it be necessary to disconnect the fiber device, reinstall the protective dust caps.
Store spare caps in a dust-free environment such as a sealed plastic bag or
3. box so that when reinstalled they do not introduce any contamination to the optics.
4.
If you suspect that the optics have been contaminated, alternate between blasting with clean, dry, compressed air and flushing with methanol to remove particles of dirt.
4
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) can cause damage to any product, add-in modules or stand alone units, containing electronic components. Always observe the following precautions when installing or handling these kinds of products
1.
Do not remove unit from its protective packaging until ready to install.
2.
Wear an ESD wrist grounding strap before handling any module or component. If the wrist strap is not available, maintain grounded contact with the system unit throughout any procedure requiring ESD protection.
3.
Hold the units by the edges; do not touch the electronic components or gold connectors.
After removal, always place the boards on a grounded, static-free surface,
4. ESD pad or in a proper ESD bag. Do not slide the modules or stand alone units over any surface.
WARNING!
Integrated circuits and fiber optic components are extremely susceptible to electrostatic discharge damage. Do not handle these components directly unless you are a qualified service technician and use tools and techniques that conform to accepted industry practices.
5
Certifications
pp
Class 1 Laser product, Luokan 1 Laserlaite,
Class 1 Laser product, Luokan 1 Laserlaite, Laser Klasse 1, A
areil A’Laser de Classe 1
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this symbol on product or packaging must not be disposed of with unsorted municipal waste. This symbol indicates that the equipment should be disposed of separately from regular household waste. It is the consumer’s responsibility to dispose of this and all equipment so marked through designated collection facilities appointed by government or local authorities. Following these steps through proper disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about proper disposal, please contact local authorities, waste disposal services, or the point of purchase for this equipment.
6
International Headquarters
B&B Electronics
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 — General Fax (815) 433-5105
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 — Fax +353 91-79244S5
Website: www.bb-elec.com
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any errors that may appear in this document. iMcV-WDM/2 is a trademark of B&B Electronics. Other brands or product names may be trademarks and are the property of their respective companies.
Document Number 49-80100-01 A1 August 2013
Loading...