Bazooka TOYOTA FJ CRUISER Installation Manual
TOYOTA FJ CRUISER
Southeast Toyota Distributors, LLC Page 1 of 9
Part Number: 00016-60009
2007- BASE TUBE (BAZOOKA®)
Accessor
y Code:
Kit Contents
Item # Quantity Reqd. Description
1 1 Bazooka Tube Assembly
2 1 Wire Harness
3 1 Hardware Bag
4 1 Care Card
Hardware Bag Contents
Item # Quantity Reqd. Description
1 4 4” Wire Ties
2 4 M6 X 30mm Bolts
3 2 M6 X 25mm Bolts
4 2 Main Plate w/ mounts
5 2 L- Mounting Plates
6 4 M6 X 30mm Bolts
7 2 Washers
Additional Items Required For Installation
Item # Quantity Reqd. Description
1
Conflicts
None
neral Applicability
Ge
All Toyota FJ Grades
Recommended Sequence of Application
Item # Accessory
1 Install Security/Audio
2 Install Bazooka Tube
3 Install Door Sills
4 Install Molded Dash
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Ite
m # Quantity Reqd. Description
1
Bass Tube Specifications
Woofer Size 8”
Voice Coil Size
1”high power/high
mp.
te
Magnet Size 15 oz.
Frequency Response 39 – 85 hz.
Efficiency 105dB
Power Handling 100 watts
Dimensions 18.125” x 8.5” x 10”
Weight 14 lbs.
Impedance 2 ohms DVC
Recommended Tools
Personal
& Vehicle
Notes
Protection
Vehicle Protection Seat/Floor Covers
Part Protection Blankets
Special Tools Notes
Installation Tools Notes
Panel Removal Tool Nylon Removal Tool (NRT)
Socket/Ratchet 10mm
Socket Extension 6 inch
Torque Wrench 3 lbf·ft
Pliers 1. Diagonal Cutters
2. Long Nose (optional)
Screwdriver Magnetized Philips # 2
Special Chemicals
TOYOTA FJ CRUISER
Southeast Toyota Distributors, LLC Page 2 of 9
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:-
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassem bly/Reassem bly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Pre-installation Precautions
(a) Use Seat & Floor Protectors and Fender
STOP
Covers/Blankets to avoid damage to
surfaces. Operator Safety Warning (if
applicable.)
2. Battery Disconnect
STOP
(a) NOTE: Be sure to open the rear hatch,
PRIOR to disconnecting the battery.
(b) Remove the NEGATIVE (-) battery
terminal using a 10mm socket before any
disassembly starts. (Fig. 2-1).
3. Disassemble Center Rear Storage Area
(a) Remove Cargo Net Cleats using 10mm
Socket. Place in a safe location.
(b) Remove Side Trim Cover, Quarter Trim
STOP
Pocket, Quarter Trim Pocket Tray. (Fig.
3-2)
Fig 2-1
Fig 3-2
BASS TUBE (BAZOOKA®)
Southeast Toyota Distributors, LLC Page 3 of 9
4. Mount L-Brackets
(a) On wheel well, slide L-brackets under
side garnish ensuring no wires are
pinched. Insert Ground ring between
front L-bracket and vehicle. DO NOT
TIGHTEN AT THIS POINT! (Fig. 4-1)
NOTE: It may be necessary to unsnap
factory harness clip to align rear L-bracket.
5. Route Wire Harness
(a) Plug harness in at point shown. (Fig. 5-1)
(b) Route Wire harness as shown. (Fig. 5-2)
(c) Secure Wire harness at regular intervals
using 4” wire ties.
Fig. 4-1
Fig 5-1
(1) Fig. 5-2
Loading...