Bazooka EL604/608, EL804/808, EL104/108, EL6A-hp, EL10A-hp Owners Manual
...
SOUTHERN AUDIO SERVICES, INC.
BATON ROUGE, LA 70819
15049 FLORIDA BLVD.
MODELS INCLUDED IN THIS MANUAL:
EL604/608, EL804/808, EL104/108, EL6A-hp, EL8A-hp, EL10A-hp,
RS604DV/608DV, RS804DV/808DV, RS104DV/108DV, RS6A-hp,
RS8A-hp, RS10A-hp, SM804, SM104, SM8A, SM10A, SM8A-hp,
SM10A-hp, CS8A5
STAMP
HERE
PLACE
Dear Friend,
CONTENTS
Thank you for selecting Bazooka® subwoofer speaker systems for your
car stereo system. Today, the Bazooka represents Bazooka Mobile Audios
continued commitment to efficiency and design. An innovative
manufacturing process developed by SAS for the Bazooka provides
consumers with state-of-the-art speaker system design.
At SAS, we take pride in manufacturing the most revolutionary bass speaker
systems ever created, featuring our patented Bass Tubes® enclosure design,
and we hope you will take pride in owning them.
Several years ago, we realized that efficiency was the wave of the future
in Autosound, so we made a commitment to design, manufacture, and
deliver the most efficient speaker systems possible.
Today we market our patented speaker systems worldwide and the high
quality of the Bazooka brand is well respected by consumers and dealers
of all nationalities.
When properly installed, Bazooka subwoofer speaker systems will give
you years of clean uninterrupted sound reproduction. Therefore, I urge
you to take a few minutes of your time to review this instruction booklet.
It was designed to give you a better understanding of our products and
to explain how to apply them properly.
Thank you again for choosing Bazookas. Our early commitment to quality
has made them the product of choice, and I am sure you will agree that
you have made the right one! Enjoy!
HELPFUL HINTS BEFORE YOU BEGIN PG 2
VEHICLE PLACEMENT RECOMMENDATIONS PG 3
BOAT PLACEMENT RECOMMENDATIONS PG 4
MOUNTING THE BAZOOKA PG 5-7
WIRING DIAGRAMS PG 8-10
SPECIFICATIONS PG 11-12
FEATURES PG 13-14
WIRING PG 15-21
TROUBLESHOOTING PG 22-23
WARRANTY PG 24-26
HELPFUL HINTSBEFORE YOU BEGIN
Please take time to read through this manual and plan out your
installation before you begin!
Locate an area in the rear of the vehicle where you would like to place
the Bazooka speaker systems. The location you have selected must
meet the following requirements in order for the Bazooka to be properly
installed in the vehicle:
Sincerely,
JON C. JORDAN
President
SAS/BAZOOKA
1) The woofer (grill end) should be facing into a corner. (See
vehicle placement recommendations on pg. 3)
2) Ideally, there should be 2 to 4 inches between the woofer and
the corner it is pointing into.
3) The mounting area should be carefully checked to be sure
that the mounting screws will not damage the gas tank,
electrical wiring, fuel lines, or the spare tire during the mounting
of the strap bases.
4) The strap mounting bases should be screwed securely to a
rigid surface that is part of, or anchored to, the structure of
the vehicle.
1
2
VEHICLE PLACEMENT RECOMMENDATIONS
TRUCK INSTALLATION
tube size is exaggerated for emphasis
HATCHBACK INSTALLATION
tube size is exaggerated for emphasis
BOAT PLACEMENT RECOMMENDATIONS
SEDAN INSTALLATION
tube size is exaggerated for emphasis
3
BOW RIDER/SKI BOAT
tube size is exaggerated for emphasis
Under passenger console
Under seat storage compartment
SPORT YACHT
tube size is exaggerated for emphasis
Under bed storage compartment
Under seat storage compartment
4
MOUNTING THE BAZOOKA
Figure 1
Logo
should
face up
To p
Figure 4
1. With the topside of the buckle facing up (see figure 1), lace the strap
through the mounting base as illustrated in figure 2
Figure 2
Figure 3
3. Place each mounting base under the Bass Tubes
the apex at the bottom of the tube sits inside the mounting base as
in figure 4.
,,
Figure 5
3
4. Move the bases so that they are spaced approximately 3 from each
end of the enclosure as illustrated in figure 5.
®
5. Remove the Bass Tubes
bases and set it aside.
enclosure without moving the mounting
®
enclosure so that
,,
3
2. After the strap is completely laced through the mounting base, make
a loop with the strap, where it runs across the middle of the base as
illustrated in figure 3. This loop is necessary to access the two mounting
holes in the base.
5
6. Screw each mounting base securely in place with screws provided
as illustrated in figure 3.
6
See Model Size
For Length
Figure 6
7. Remove any slack in the strap by feeding it out of the mounting
base on the loose end of the strap opposite the buckle.
EL WIRING DIAGRAM
8. Place the Bass Tubes
®
enclosure on the mounting bases and fasten
the buckles as illustrated in figure 7. The strap should loop through
the buckle and be tightened securely by holding the strap in place with
one hand and pulling the loose end away from the buckle, but against
the cabinet.
Model Length
6 17
8 22
10 27
Figure 7
Technical Note:
Due to the jarring and shifting that can occur in a vehicle, the mounting
straps may stretch or loosen. We recommend that you check the straps
regularly to assure that your Bass Tubes
in place.
®
enclosure is mounted securely
OPTIONAL
REMOTE
LEVEL
CONTROL
16 GAUGE
BLACK CHASSIS
GROUND
16 GAUGE RED
INPUT
PHASE
SWITCH
QUICK DISCONNECT
YELLOW ON/OFF
JUMPER LOOP
GRAY
HI-LEV
INPUT (+)
GRAY/TRACE
HI-LEV
INPUT (-)
LEVEL
GN/TRACE
HI-LEV
INPUT (-)
GREEN
HI-LEV
INPUT (+)
RCA
PHONO PLUGS
Right & Left Low
Level Inputs
BATTERY (12v+)
ORANGE
REMOTE
NOTE:
REMOVE AUTO TURN-ON LOOP TO USE ORANGEREMOTE
WIRE FOR NORMAL REMOTE TURN-ON
7
8
Loading...