Bazooka EL104, EL108, EL604, EL608, EL6A-hp Installation Manual

PLACE

STAMP

HERE

SOUTHERN AUDIO SERVICES, INC.

15049 FLORIDA BLVD.

BATON ROUGE, LA 70819

MODELS INCLUDED IN THIS MANUAL:
EL604/608, EL804/808, EL104/108, EL6A-hp, EL8A-hp, EL10A-hp,
RS604DV/608DV, RS804DV/808DV, RS104DV/108DV, RS6A-hp,
RS8A-hp, RS10A-hp, SM804, SM104, SM8A, SM10A, SM8A-hp,
SM10A-hp, CS8A5

Dear Friend,

Thank you for selecting Bazooka® subwoofer speaker systems for your
car stereo system. Today, the Bazooka represents Bazooka Mobile Audios
continued commitment to efficiency and design. An innovative
manufacturing process developed by SAS for the Bazooka provides
consumers with state-of-the-art speaker system design.

At SAS, we take pride in manufacturing the most revolutionary bass speaker
systems ever created, featuring our patented Bass Tubes® enclosure design,
and we hope you will take pride in owning them.

Several years ago, we realized that efficiency was the wave of the future
in Autosound, so we made a commitment to design, manufacture, and
deliver the most efficient speaker systems possible.

Today we market our patented speaker systems worldwide and the high
quality of the Bazooka brand is well respected by consumers and dealers
of all nationalities.

When properly installed, Bazooka subwoofer speaker systems will give
you years of clean uninterrupted sound reproduction. Therefore, I urge
you to take a few minutes of your time to review this instruction booklet.
It was designed to give you a better understanding of our products and
to explain how to apply them properly.

Thank you again for choosing Bazookas. Our early commitment to quality
has made them the product of choice, and I am sure you will agree that
you have made the right one! Enjoy!

Sincerely,

JON C. JORDAN
President
SAS/BAZOOKA

1

2

HELPFUL HINTS BEFORE YOU BEGIN PG 2

VEHICLE PLACEMENT RECOMMENDATIONS PG 3

BOAT PLACEMENT RECOMMENDATIONS PG 4

MOUNTING THE BAZOOKA PG 5-7

WIRING DIAGRAMS PG 8-10

SPECIFICATIONS PG 11-12

FEATURES PG 13-14

WIRING PG 15-21

TROUBLESHOOTING PG 22-23

WARRANTY PG 24-26

CONTENTS

HELPFUL HINTSBEFORE YOU BEGIN

Please take time to read through this manual and plan out your
installation before you begin!

Locate an area in the rear of the vehicle where you would like to place
the Bazooka speaker systems. The location you have selected must
meet the following requirements in order for the Bazooka to be properly
installed in the vehicle:

1) The woofer (grill end) should be facing into a corner. (See
vehicle placement recommendations on pg. 3)

2) Ideally, there should be 2 to 4 inches between the woofer and
the corner it is pointing into.

3) The mounting area should be carefully checked to be sure
that the mounting screws will not damage the gas tank,
electrical wiring, fuel lines, or the spare tire during the mounting
of the strap bases.

4) The strap mounting bases should be screwed securely to a
rigid surface that is part of, or anchored to, the structure of
the vehicle.

HATCHBACK INSTALLATION

tube size is exaggerated for emphasis

TRUCK INSTALLATION

tube size is exaggerated for emphasis

SEDAN INSTALLATION

tube size is exaggerated for emphasis

VEHICLE PLACEMENT RECOMMENDATIONS

3

BOW RIDER/SKI BOAT

tube size is exaggerated for emphasis

 Under passenger console
 Under seat storage compartment

SPORT YACHT

tube size is exaggerated for emphasis

 Under bed storage compartment
 Under seat storage compartment

BOAT PLACEMENT RECOMMENDATIONS

4

1. With the topside of the buckle facing up (see figure 1), lace the strap
through the mounting base as illustrated in figure 2

MOUNTING THE BAZOOKA

2. After the strap is completely laced through the mounting base, make
a loop with the strap, where it runs across the middle of the base as
illustrated in figure 3. This loop is necessary to access the two mounting
holes in the base.

Figure 1

Figure 2

Figure 3

To p

Logo
should
face up

5

Figure 5

3

,,

3

,,

Figure 4

4. Move the bases so that they are spaced approximately 3 from each

end of the enclosure as illustrated in figure 5.

5. Remove the Bass Tubes

®

enclosure without moving the mounting

bases and set it aside.

6. Screw each mounting base securely in place with screws provided

as illustrated in figure 3.

6

3. Place each mounting base under the Bass Tubes

®

enclosure so that
the apex at the bottom of the tube sits inside the mounting base as
in figure 4.

NOTE:
REMOVE AUTO TURN-ON LOOP TO USE ORANGEREMOTE
WIRE FOR NORMAL REMOTE TURN-ON

LEVEL

GRAY/TRACE

HI-LEV

INPUT (-)

GN/TRACE

HI-LEV

INPUT (-)

ORANGE
REMOTE

QUICK DISCONNECT

YELLOW ON/OFF

JUMPER LOOP

GRAY

HI-LEV

INPUT (+)

GREEN
HI-LEV

INPUT (+)

RCA

PHONO PLUGS

Right & Left Low

Level Inputs

16 GAUGE

BLACK CHASSIS

GROUND

16 GAUGE RED

BATTERY (12v+)

INPUT
PHASE

SWITCH

OPTIONAL

REMOTE

LEVEL

CONTROL

EL WIRING DIAGRAM

8

7. Remove any slack in the strap by feeding it out of the mounting
base on the loose end of the strap opposite the buckle.

8. Place the Bass Tubes

®

enclosure on the mounting bases and fasten
the buckles as illustrated in figure 7. The strap should loop through
the buckle and be tightened securely by holding the strap in place with
one hand and pulling the loose end away from the buckle, but against
the cabinet.

Figure 7

See Model Size

For Length

Figure 6

Technical Note:

Due to the jarring and shifting that can occur in a vehicle, the mounting
straps may stretch or loosen. We recommend that you check the straps
regularly to assure that your Bass Tubes

®

enclosure is mounted securely

in place.

Model Length
6 17
8 22
10 27

7

CS8A5 WIRING DIAGRAM

10

Blue - remote turn on

Orange/Purple - rear right neg. speaker output

Brown - rear left pos. speaker output

Brown/Green - rear left neg. speaker output

Orange - rear right pos. speaker output

F/R GAIN

SUB GAIN

POWER

PHASE

REMOTE

OUTPUT

B-

B+

INPUT

White - front left pos. input

White/Black - front left neg. input

Grey - front right pos. input

Grey/Black - front right neg. input

Green - rear left pos. input

Green/Black - rear left neg. input

Purple - rear right pos. input
Purple/Black - rear right neg. input

Yellow - front right pos. speaker output

Yellow/Grey - front right neg. speaker output

Red - front left pos. speaker output

Red/White - front left neg. speaker output

Black - battery ground

Red - battery positive

15 AMP

X-OVER

LEVEL

BROWN

HI-LEVEL

OUTPUT (+)

GRAY/TRACE

HI-LEV

INPUT (-)

GREEN/TRACE

HI-LEV

INPUT (-)

ORANGE
REMOTE

YELLOW

HI-LEVEL

OUTPUT (-)

GRAY

HI-LEV

INPUT (+)

GREEN
HI-LEV

INPUT (+)

RCA PHONO PLUGS

Right & Left Low Level Inputs

12 GAUGE

BLACK

CHASSIS

12 GAUGE

RED

BATTERY

(12v+)

AMPLIFIER
STATUS LED

AUTO

TURN-ON

JUMPER

SWITCH

OPTIONAL

REMOTE

CONTROL

CONNECTOR

RS WIRING DIAGRAM

9

MARINE TUBE SPECIFICATIONS

SM804 SM104 SM8A SM10A SM8A-hp SM10A-hp

Woofer Size 8 10 8 10 8 10

Voice Coil Size 1 high power. /high temp. 1.5 high power. /high temp. 1 high power /high temp 1.5 high power. /high temp. 1.5 high power. /high temp. 1.5 high power. /high temp.

Magnet Size 28 oz. 28 oz. 15 oz. 28 oz. 28 oz. 28 oz.

Frequency response* 39-1500 hz. 39-1000 hz. 39-85 hz. 39-85 hz. 39-250 hz. 39-250 hz.

Efficiency** 102 dB* 104 dB* 105 dB* 107 dB* 102 dB* 104 dB*

Power Handling 6-150 watts/channel 6-200 watts/channel 100 watts 100 watts 150 watts 150 watts

Dimensions 18 x 8.5 x 10 20.75 x 10.3 x 12.2 18.125x8.5x10 20.875x10.3x12.2 18.325" x 8.5" x 10" 21.1" x 10.3" x 12.2"

Weight 15.5 lbs. 23 lbs. 14 lbs. 24 lbs. 20 lbs. 25 lbs.

Impedance 4 ohms/8 ohms 4 ohms/8 ohms 2 ohms DVC 2 ohms DVC 4 ohms 4 ohms

* The built in crossover limits the frequency response of the Amplified Bazooka.

** The efficiency levels of all Bazooka subwoofer speaker systems are measured in the typical environment: In the low bass region with one watt of power.

12

AMPLIFIED TUBE SPECIFICATIONS

EL6A-hp EL8A-hp EL10A-hp RS6A-hp RS8A-hp RS10A-hp CS8A5

Woofer Size 6.5 8 10 6.5 8 10 8

Voice Coil Size 1 high power. /high temp. 1 high power. /high temp. 1.5 high power. /high temp. 1 high power. /high temp. 1.5 high power. /high temp. 1.5 high power. /high temp. 1 high power. /high temp.

Magnet Size 13 oz. 15 oz. 28 oz. 20 oz. 28 oz. 28 oz. 28 oz.

Frequency response* 39-85 hz. 39-85 hz. 39-85 hz. 39-250 hz. 39-250 hz. 39-250 hz. sub 20-100hz/Hi-pass 100-20khz

Efficiency** 103 dB* 105 dB* 107 dB* 100 dB* 102 dB* 104 dB* 105 dB*

Power Handling 100 watts 100 watts 100 watts 150 watts 150 watts 150 watts sub 100w x 1/hi-pass 25w x 4

Dimensions 18.125 x 6.75 x 8 18.125 x 8.5 x 10 20.875 x 10.3 x 12.2 18.325" x 6.75"x 8" 18.325" x 8.5" x 10" 21.1" x 10.3" x 12.2" 18.325" x 8.5" x 10"

Weight 12 lbs. 14 lbs. 24 lbs. 15 lbs. 20 lbs. 25 lbs. 20 lbs.

Impedance 2 ohms DVC 2 ohms DVC 2 ohms DVC 4 ohms 4 ohms 4 ohms 2 ohms DVC

PASSIVE TUBE SPECIFICATIONS

EL604/608 EL804/808 EL104/108 RS604DV/608DV RS804DV/808DV RS104DV/108DV

Woofer Size 6.5 8 10 6.5 8 10

Voice Coil Size 1 high power. /high temp. 1.5 high power. /high temp. 1.5 high power. /high temp. 1.5 high power. /high temp. 2 high power. /high temp. 2 high power. /high temp.

Magnet Size 20 oz. 28 oz. 28 oz. 28 oz. 36 oz. 36 oz.

Frequency response* 39-1500 hz. 39-1500 hz. 39-1000 hz. 39-1500 hz. 39-1500 hz. 39-100 hz.

Efficiency** 100 dB* 102 dB* 104 dB* 100 dB* 102 dB* 104 dB*

Power Handling 6-100 watts/channel 6-150 watts/channel 6-200 watts/channel 6-150 watts/channel 6-200 watts/channel 6-250 watts/channel

Dimensions 18 x 6.75 x 8 18 x 8.5 x 10 20.75 x 10.3 x 12.2 18" x 6.75"x 8" 18" x 8.5" x 10" 20.75" x 10.3" x 12.2"

Weight 11 lbs. 15.5 lbs. 23 lbs. 13 lbs. 19 lbs. 26 lbs.

Impedance 4 ohms/8 ohms 4 ohms/8 ohms 4 ohms/8 ohms 4 ohms/8 ohms 4 ohms/8 ohms 4 ohms/8 ohms

11

MODEL FEATURES

XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXX

XXX
XXX
XXX

XXX XX

XXX XX
X
X XXX XXX XXXX
X XXX XX

XXX XX
X XXX XXX XXXX

XXX XXX XX

X XXX XXX XXXX

XXX XX
XXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXX

XXX

XXX XX

XXXXXX
XXXXXX
XXXXXX
XXXXXX

XXXXXXX XXXXXX

XXXXXX

CS8A5

EL604/8

EL804/8

EL104/8

EL6A-hp

EL8A-hp

EL10A-hp

RS604DV

RS804DV

RS104DV

RS6A-hp

RS8A-hp

RS10A-hp

SM804

SM104

SM8A

SM10A

SM8A-hp

SM10A-hp

Feature

Patented Bass Tubes

®

enclosure design
Optimized for Corner Loading
Water resistant enclosure
Fits in all vehicles
Upgrades any 12 volt sound system
Perfect for leased vehicles
Home audio quality sound
New and improved cosmetics
Dual voice coil inputs
Large oversized edge roll
Oversized magnet and motor structure
Built-in 100 watt mono amplifier
Built-in 150 watt mosfet mono amplifier
Built-in 4 x 25 watt/channel front stage amplifier
Noise rejecting balanced input circuit
Fixed 85 hz 18 dB subwoofer crossover
Variable 60 - 250 hz subwoofer crossover
Built-in 12dB subsonic filter at 35 hz
Selectable Automatic turn on circuit
Optional remote subwoofer control
Optional remote crossover control
Optional Universal Mounting System
Jet black paint finish
Spring loaded terminals
Gold plated 5-way binding posts
Salt fog and UV certified for 5 years
Waterproof woofers
Stainless steel hardware
Weather resistant velcro reinforced mounting straps
One year warranty
Two year warranty

14

13

AMPLIFIED MODELS:

(EL6A-hp, EL8A-hp, EL10A-hp, RS6A-hp, RS8A-hp, RS10A-HP, CS8A5,
SM8A, SM8A-hp , SM10A, SM10A-hp)

DO NOT substitute the fuse included with the Amplified Bazooka subwoofer
with anything other than the SAME fast blow current rated fuse. Substitution
or deletion will void the product's warranty and may cause damage to your
car or the amplifier.

SHOULD I USE HIGH OR LOW LEVEL INPUTS?

If the source unit has only speaker outputs, use the high-level inputs of the
Amplified Bazooka subwoofer. If the source unit has both high and low level
outputs, we recommend using the high level inputs over the low level inputs,
due to the configuration of the Amplified Bazooka subwoofer's balanced input
circuit. Not all head units, even those that promise high output voltage in their
marketing materials, indeed have high-voltage RCA outputs. Because of this,
Bazooka Mobile Audio recommends using the speaker level inputs when in
doubtthey will always provide sufficient drive level to the amplifier. PLEASE
NOTE THAT THE WIRING IN A FACTORY STEREO MAY NOT BE ELECTRICALLY
IN PHASE EVEN WHEN YOU HAVE MADE THE PROPER CONNECTIONS.

Take the time after you make your wire connections to run through the quick
phase check procedure in the AM I IN PHASE? section at the end of this
manual, and NEVER USE BOTH high and low-level inputs at the same time!

POWER WIRE (All Models)

The power wire must be fused and connected directly to the positive terminal
of the battery to provide a power source with a low voltage drop and low
noise. Do not make the power connection at the fuse block or any point other
than the battery. Improper power sources can reduce output and cause distortion.

The fuse holder should be connected to the battery's positive terminal. The
fuse is designed to prevent fire or damage to your car, should the battery
wire short to ground. Wait to insert the fuse into its holder until all wire
connections have been made.

If it is necessary to lengthen the battery wire, add the required length between
the amplifier and the fuse holder, not the fuse holder and the battery. If you
need to extend the battery wire, use 16 gauge or larger for all EL Amplified,
SM8A, and SM10A models, and 12 gauge or larger for all RS Amplified, SM8A­hp, SM10A-hp, and CS8A5 models. It is best to use as short a wire as possible.
Be sure you DO NOT run the power wire next to the input cables of the
amplifier this will induce noise. Avoid running the power wire near the radio's
antenna or power leads, or near sensitive equipment or harnesses. The power
wire carries substantial currents and could induce noise.

15

GROUND WIRE (All Models)

The ground wire must be connected directly to the vehicle chassis near
the amplifier. We do not recommend extending the ground wire in
any installation, as this can cause unwanted ground loops.
The ground point in the car should be a piece of chassis metal that is
part of or welded to the main body of the vehicle. Painted surfaces
should be scraped or sanded clean to expose the bare metal before the
ground lug is bolted down. (Cover the bare metal area with paint or
grease after you finish mounting the ground wire to prevent rust.)

REMOTE TURN ON OPTIONS (Does not apply to CS8A5)

You have several options in connecting the Remote Turn On Wire. These
options are listed in the order of preference recommended by SAS.
Select the option best suited for your application. The ORANGE wire
on the Amplified Bazooka subwoofers 14-pin Molex Mini-fit Jr. connector
is the Remote Turn On Wire.

OPTION ONE:

For the most versatility the Remote Turn On Wire should be connected
to the source unit's "Accessory", "Auto-Antenna" or "Remote" lead -

- any of which will supply 12 Volts positive when the source is turned
on. When you are using this option with:

ALL EL Amplified, SM8A, and SM10A: The Quick Disconnect YELLOW
On/Off Jumper Loop MUST be disconnected from the wiring harness.

ALL RS Amplified, SM8A-hp, and SM10A-hp: The Auto/off Jumper
Clip must be in the off position (the two right most pins) and the Orange
wire will supply turn on voltage to the Amplified Bazooka.

OPTION TWO:

If the source does not have an Auto-Antenna lead (or if the Auto­Antenna goes down during tape operation), you can connect the
Amplified Bazookas' Remote Turn On Wire to an accessory or ignition
point at the vehicle fuse block. In this configuration, the Amplified
Bazooka subwoofer will be on whenever the ignition is on. This method
may allow noise or turn-on-and-off transients to become amplified
when the source unit is not in use, and therefore is a less desirable than
option one. When you are using this option with:

ALL EL Amplified, SM8A, and SM10A: The Quick Disconnect YELLOW
On/Off Jumper Loop MUST be disconnected from the wiring harness.

16

ALL RS Amplified, SM8A-hp, and SM10A-hp: The Auto/off Jumper Clip
must be in the off position (the two right most pins) and the Orange wire will
supply turn on voltage to the Amplified Bazooka.

OPTION THREE:

The Amplified Bazooka subwoofer has a built-in Auto Turn-On Feature. If you
choose to use this feature, the Amplified Bazooka subwoofer will turn on
automatically whenever there is music present at the inputs (high level or low
level input). To use the Auto Turn-On Option with:

ALL EL Amplified, SM8A, and SM10A: Locate the Auto/Off Jumper Loop
located on the wiring harness; SAS ships the Amplified Bazooka subwoofer
with this Jumper in the ON Position. The Quick Disconnect YELLOW On/Off
Jumper Loop must be plugged into the harness.

ALL RS Amplified, SM8A-hp, and SM10A-hp: Locate the Auto/Off Jumper
Clip located on the back of the unit; SAS ships the Amplified Bazooka subwoofer
with this Jumper in the Off Position. The Jumper must be placed in the Auto
Position. The Jumper Clip must be lifted off of the middle and right hand pins
and reinserted across the left hand.

INPUT SIGNAL CONNECTIONS (Does not apply to CS8A5)

High-Level Inputs:

If the source unit has both front and rear speaker outputs, use only one set of
speaker outputs for the high-level input of the Amplified Bazooka. Connect
the GREEN wire from the 14-pin Molex plug of the Amplified Bazooka subwoofer
to the source units left (+) positive speaker output. Connect the GREEN W/BLACK
stripe wire of the plug to the source units left (-) negative speaker output.
Connect the GRAY wire of the plug to the source units right (+) positive speaker
output. Connect the GRAY W/BLACK stripe wire of the plug to the source units
right (-) negative speaker output. When using high-level inputs, take the time
after you make all wiring connections to run through the AM I IN PHASE
procedure at the end of this manual to confirm that your inputs are in correct
electrical phase and the proper bass response is being produced.

Low-Level Inputs:

If your source unit only has low-level RCA phono jack output, use only the low­level inputs of the Amplified Bazooka. Connect the low-level RCA phono jack
inputs of the Amplified Bazooka subwoofer to the source with a shielded RCA
patch cord. To avoid possible noise problems, be sure to run the patch cord
away from all power wires and factory wire harnesses. When using the low­level inputs DO NOT make any connections to the Green and Gray high-level
input wires of the Amplified Bazooka subwoofer and make sure these wires
are insulated to avoid the possibility of a short circuit.

17

ADJUSTING THE CROSSOVER (All RS Amplified, SM8A-hp,
and SM10A-hp ONLY)

The built-in crossover on the Amplified Bazooka subwoofer is an 18
dB per octave electronic low pass filter, it has a 60 Hz to 250 Hz variable
crossover point. Select the crossover point that you feel best fits your
system design. Set the potentiometer labeled XOVER to the point you
selected, 60 Hz being all the way to the left (counterclockwise) and
250 Hz being all the way to the right (clockwise). When you have set
the crossover, proceed to the next step.

CS8A5 TURN ON & INPUT/OUTPUT CONNECTIONS:

Turn On:

The BLUE with WHITE wire on the CS8A5s 10-pin connector is the
remote turn on wire. You have two options in connecting the remote
turn on wire. Select the option best suited for your application.

Option One:

For the best functionality, the remote turn on wire should be connected
to the source unit's "Accessory", "Auto-Antenna" or "Remote" lead

-- any of which will supply 12 Volts positive when the cars radio is
turned on.

Option Two:

If the source does not have an Auto-Antenna lead (or if the Auto­Antenna goes down during tape or CD operation), you will need to
connect the remote turn on wire to an accessory or ignition point at
the vehicle fuse block. In this configuration, the CS8A5 will be on
whenever the ignition is on. This method may allow noise or turn-

on-and-off transients to become amplified when the source
unit is not in use.

18

INPUT/OUTPUT HARNESS CONNECTOR DETAIL

8 pin input connector: (1)

White Front Left Positive Input
White/Black Front Left Negative Input

Grey Front Right Positive Input
Grey/Black Front Right Negative Input

Green Rear Left Positive Input
Green/Black Rear Left Negative Input

Purple Rear Right Positive Input
Purple/Black Rear Right Negative Input

10-pin speaker output connector: (2)

Red Front Left Positive Speaker Output
Red/White Front Left Negative Speaker Output

Yellow Front Right Positive Speaker Output
Yellow/Gray Front Right Negative Speaker Output

Brown Rear Left Positive Speaker Output
Brown/Green Rear Left Negative Speaker Output

Orange Rear Right Positive Speaker Output
Orange/Purple Rear Right Negative Speaker Output

Blue Remote Turn On (3)

(1) This connector is for INPUTS ONLY! These wires need to be connected
directly to the output of the radio.

(2) This connector is for OUTPUTS only! NEVER connect any wires from
this plug to ground, as serious damage to amplifier could occur

(3) You have two options for this connection. See Remote Turn on
Options on page 13.

19

PHASE SWITCH (All EL Amplified, SM8A, SM10A, and CS8A5)

When one of the High-level Input channels is out of phase electrically with
the other High-level Input channel, your Amplified Bazooka subwoofer will
sound as if it has little or no output and any output that is produced may
sound distorted. If you suspect that your Amplified Bazooka subwoofer is
out of phase, use the AM I IN PHASE procedure to diagnose and correct the
Amplified Bazooka subwoofer output, and proper bass response will be
produced.

To correct this situation, simply flip the phase switch on the Amplified Bazooka.
When the input signal is in correct electrical phase, the level of bass output
will be greatest when the balance control of the radio is set to the center
position.

SETTING THE LEVEL (All Models)

Locate the potentiometer labeled LEVEL. This is the level control. Start with
the level control turned all the way to the left (counterclockwise). The bass
should be off or very low at this point. Turn up your head unit until the sound
from the existing speakers starts to clip or distort. This is the point in your
system where you will get maximum volume with the least amount of
distortion. With the head unit at this point, turn the level gain control up
slowly until the bass volume blends well with the existing high frequency
speakers. This should be the proper setting for the level gain control. Now
that the level is set, you may want to go back to the x-over control and adjust
the x-over point by ear to meet the desired sonic quality of your system design
(All RS Amplified, SM8A-hp, and SM10A-hp models ONLY have adjustable
crossovers).

LED POWER INDICATOR

If power, ground and remote are connected properly, the green LED light will
illuminate.

WHITE = OFF (ALL RS Amplified, SM8A-hp, and SM10A-hp)
GREEN = NORMAL OPERATION (ALL Models)
RED = PROTECTION MODE (ALL RS Amplified, SM8A-hp, and SM10A-hp)

OPTIONS (All EL Amplified, SM8A, SM10A, and CS8A5)
Remote Bass Control (RBCM-EL):

If you find you like to change the level of bass depending on what you are
listening to and want an easy way to make this possible, you can purchase
an optional Remote Level Control.

20

TROUBLESHOOTING

Am I In Phase?

If your inputs are out of phase and you turn the balance control
of your radio all the way to one side, right or left, the bass output
from the Bazooka

®

will increase. When you bring the balance
control back to the center position the bass level will drop. This
confirms that one of your input channels is wired out of phase
with the other.

When one of the Amplified Bazooka's High-level Input channels
is out of phase electrically with the other High-level Input channel,
your Bazooka will sound as if it has little or no output and any
output that is produced may sound distorted. If you suspect that
your Bazooka is out of phase, use the AM I IN PHASE procedure
to diagnose and correct the Bazookas' output, and proper bass
response will be produced. channels is wired out of phase with
the other. To correct this situation, simply flip the phase switch
on the amplified Bazooka

®

. When the input signal is in correct
electrical phase, the level of bass output will be greatest when
the balance control of the radio is set to the center position.

Do You Have A Phase Problem?

If the bass response in your application appears to be lower then
you expected or sounds muffled and or distorted, you may be
experiencing Phase Cancellation.

Phase Cancellation

When two speakers in the same frequency range produce sound
waves that are inverted from one another or 180° out of phase,
the sound waves will cancel each other out to some degree. This
effect will be heard as a drop in the output level and/or a muffled
or muddy quality in the Bass Response. The source of this Phase
Cancellation can be at any point in the signal path. The obvious
cause of this problem would be a speaker connection that was
reversed in polarity, but that is not always the case. Sometimes
amplifier channels will shift phase 180° for no good reason, or
a signal processor could have a setting for phase that has been
set incorrectly or the source material could just be recorded in
error. Also speaker placement and the acoustics of the listening
environment can effect the phase. No matter what or where the
cause is located, the solution is an easy one.

22

All RS AMPLIFIED, SM8A-HP, SM10A-HP.

Remote Bass Control and Crossover (RBCM-RS):

If you find you like to vary the crossover point in addition to changing
the level of bass depending on what you are listening to and want an
easy way to make this possible, you can purchase an optional Remote
Level and Crossover Control.

These Remote Controls are accessories that are available from your
Bazooka dealer or directly from Bazooka. Be sure to check out other
optional accessories for your Bazooka at

PASSIVE MODELS

(EL604, EL608, EL 804, EL808, EL104, EL108, SM804, SM104 ONLY)

On the back of all Bazooka El and Marine passive models you will find
a terminal cup with two spring loaded terminals, red being positive
and black being negative. Hook the positive speaker output from your
amplifier to the red positive terminal of the Bazooka. Hook the negative
speaker output from your amplifier to the black negative terminal.
Repeat these steps for each Bazooka used.

(RS604DV, RS608DV, RS804DV, RS808DV, RS104DV, RS108DV)

On the back of all Bazooka Reference Series passive models you will
find a terminal cup with two 5 way gold binding posts, red being
positive and black being negative. Hook the positive speaker output
from your amplifier to the red positive terminal of the Bazooka. Hook
the negative speaker output from your amplifier to the black negative
terminal. Repeat these steps for each Bazooka used.

21

PHASE CORRECTING PROCEDURE

Disconnect all but one Bazooka

®

from your system. Be sure that
any loose wire connections are insulated to avoid the chance of
short-circuiting any of the electronic equipment. Listen to the
system and take note of the level of the Bass Response. Connect
the next Bazooka

®

and compare the level of the combined output
to that of the single unit. If the Bass Response increases, the
Phasing is correct and you can repeat this process on the next
Bazooka. If the level of the Bass Response drops, the Phasing is
incorrect and you should reverse the speaker connections to this
Bazooka

®

and compare again. In short to INCREASE IS GOOD,

to DECREASE IS BAD! Using this method, any number of
Bazooka

®

subwoofers can be kept in absolute phase.

PRACTICE SAFE LISTENING

Continuous exposure to high volumes of sound may cause
permanent hearing loss. High-powered auto sound systems are
capable of producing sounds well over 130 dB. Even short periods
of play at high volume levels can impair your ability to hear
necessary traffic sounds and may constitute a hazard. Please use
common sense and practice SAFE LISTENING!

If you have any questions contact the

SAS Technical Support Department at:

Phone - (800) THE TUBE  Fax - [phone]

In Canada: [phone]

Email - [e-mail]  Website - www.bazooka.com

15049 Florida Blvd., Baton Rouge, LA. 70819

23

LIMITED WARRANTY (UNITED STATES)

Southern Audio Services, Inc., warrants all products to be free from defects

in material and workmanship for a period of one (1) year from the date of purchase;
the Reference Series is warranted for a period of two (2) years from date of
purchase.

In the event the product is not as warranted, SAS sole obligation shall
be to repair or replace the defective product at SAS option: SAS limits
its obligation under any implied warranties under state laws to a period
not to exceed the limited warranty period. SAS and its authorized
BAZOOKA

®

dealers specifically disclaim liability for any incidental or
consequential damages. Some states to not allow limitations on how
long an implied warranty lasts, and some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above
limitation or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may have other rights, which vary from
state to state.

What is covered:

This warranty covers all defects in materials or workmanship (parts and labor) in
the product.

What is not covered:

This warranty does not cover the following:

1. Damages occurring during shipment of the product to SAS for repair (claims

must be presented to the carrier).

2. Damages caused by accident, abuse, negligence, misuse or improper operation

or installation.

3. Damages caused by an act of God, including without limitation, fire, flood,

storms, or other acts of nature.

4. Any product, which has a serial number, defaced, altered, modified, or removed.

5. Any product that has been altered or modified without SAS consent.

How to obtain warranty services:

1. You are responsible for delivery of the product to an authorized BAZOOKA

®

dealer or contact SAS at 1-800-THE TUBE for a Return Authorization number.
The Return Authorization number must be clearly written on the outside of the
box. Freight must be prepaid to SAS. Warranty replacement parts will be
returned freight prepaid. The entire enclosure may be returned for warranty
service, but return will be freight collect.

2. You must provide proof of the date of purchase of the product. If proof of

purchase is not provided, original date of manufacture will be used to determine
warranty period.

3. You must package the product securely to avoid damage during shipment.

4. After acquiring a Return Authorization number, ship to the address below.

24

IN MEXICO:

COIBA IMPORT S.A. DE C.V
Torrecillas # 2060
Guadalajara Jalisco Col. El Rosario
México C.P. 44890
Modelo: EL604/608, EL804/808, EL104/108, EL6A-hp, EL8A-hp, EL10A-hp,

RS604DV/608DV, RS804DV/808DV, RS104DV/108DV, RS6A-hp,
RS8A-hp, RS10A-hp, SM804, SM104, SM8A, SM10A, SM8A-hp,
SM10A-hp, CS8A5

RFC CIM-000901-1k0 Producto: Bocinas

POLIZA DE GARANTIA CONDICIONES

El producto que usted ha adquirido Cuenta con una garantía de 90 días Por
defectos de fabricación y 90 días De servicio a partir de la fecha de Adquisición
otorgada por:
COIBA IMPORT S.A. DE C.V

1.- Para hacer efectiva esta garantía, usted debe presentar la factura de compra o
póliza debidamente llenada por la tienda o unidad vendedora junto con el
producto.

2.- La empresa e compromete a reparar al producto, sin costo alguno al consumidor;
si la falla es atribuible a defecto de fabricación.

3.- El tiempo de reparación en ningún caso será mayor de 30 días, transcurrido este
término COIBA IMPORT S.A. DE C.V. procederá a Efectuar el cambio por un
producto equivalente.

4.- Centro de Servicio:Torrecillas #2060 Guadalajara Jal. Col. El Rosario C.P. 44890

Esta garantía no es valida en los siguientes casos

1.- Cuando el producto no ha sido utilizado de acuerdo al instructivo.

2.- Si no se ha observado las advertencias señaladas

3.- Si ha sido expuesto a cambios bruscos de voltaje

4.- Si ha sufrido deterioro escencial irreparable atribuido al consumidor

5.- Cuando el producto ha sido alterado o reparado por personas jenas a nosotros

6.- Esta póliza es nula si no cuenta abajo con los datos requeridos y sellos de la
tienda donde se realizó la compra.

GARANTIA VALIDA EN TU TIENDA DE SERVICIO

DATOS DEL DISTRIBUIDOR

Nombre:________________________________________________________________________

Calle y #________________________________________________________________________

Colonia ________________________________________________________________________

Producto:______________________________________________________________________

Fecha de compra:_____________________________________________________________

25

Sello y firma

De la tienda

26

____________________________________________

MODEL#

____________________________________________

SERIAL#

____________________________________________

PURCHASE DATE

____________________________________________

DEALER PURCHASED FROM

____________________________________________

DEALER ADDRESS

____________________________________________

TELEPHONE

____________________________________________

PURCHASERS NAME

____________________________________________

STREET ADDRESS

____________________________________________

CITY

____________________________________________

STATE ZIP

____________________________________________

TELEPHONE

____________________________________________

E-MAIL

PLEASE RETURN THIS PORTION IMMEDIATELY