Page 1
Remove fuse from 6 ft power cable (12). Attach the red wire to the positive battery terminal. Attach the black wire
to the negative battery terminal. Run power cable to the location of the BPB24. making sure power wire does not
hinder the safe operation of the vehicle. Plug the red power cable end into the BPB24’s red input power plug. The
black 12vdc accessory plug can be used to power any 12vdc accessory up to 15 amps. Use the included black
accessory pigtail (11) to wire your accessories.
1. Party Bar (BPB24, BPB24-DS) 1 ea.
2. Integrated (Optional) Mounting Nuts 6mm 7 ea.
3. Mounting Leg 2 ea.
4. Rubber Vibration Insulation Pads 2 ea.
5. Socket Head Cap Screw 8mm X 16mm 2 ea.
6. Low Profile Socket Head Cap Screw 6mm X 16mm 2 ea.
7. Socket Head Cap Screw 6mm X 30mm 2 ea.
8. Washer 6mm - Narrow 2 ea., Wide 2 ea.
9. Nylon Insert Locking Nut 6mm 2 ea.
10. Stud 6mm x 40mm 2 ea.
11. Accessory Pigtail 1 ea.
12. Power Cable 6 ft. 1 ea.
IMPORTANT NOTICE:
The internal RF circuit for the remote control will draw a small amount of current because it must always be ON
listening for the remote commands. Over time this could draw down your battery when your machine remains in
storage without being connected to a charger or not being actively used. For this reason, we recommend
connecting the Party Bar to a switched master power source or disconnecting the main power wire when the
machine is in storage. We also make a plug & play inline 12v master power switch that can be easily added to the
main battery wire for the Party Bar to completely kill power to the unit. It is listed under the Accessories tab on the
Party Bar product page on our website (Model number: PR-ILS16)
Warning:
If you are using the cast aluminum mounting legs to secure the Party Bar to your machine, the mounting legs must
FIRST be attached and tightened to the Party Bar before mounting it to your machine. Attaching the legs to the
machine first and then inserting the Party Bar between them can cause misalignment, spacing, and torque issues
that can cause damage to the mounting assembly resulting in a failure.
See Warning Below!
End Mounting Options
with Cast Aluminum Legs
Rev.7/11/2017 Pg. 1
1.
3 .
4.
5.
6.
7.
8.
9.
10.
11.
12.
2.
BPB24 / BPB24-DS
or BPB36
Installation Instructions
BPB24 / BPB24-DS
or BPB36
Installation Instructions
Intergrated Mounting Rail Options
2” Clamp
1.75” Clamp
2” - 1.5” Clamp
Rev.7/11/2017 Pg. 4
When using the Intergrated Mounting Rail System,
first determine your mounting stud spacing then screw
the 6mm X 40mm studs (10) into themounting nuts. Mark
your desired spacing onto theflat surface to which you are
mounting. Use a 1/4” or 7mm drill bit to drill mounting holes.
Mount the Party Bar to your mounting surface using the 6mm
washers (8) and 6mm nylon locking nuts (9) provided in
hardware kit. You can also use our optional PR-URM, PR-FRC175,
and PR-FRC200 clamps (sold separately) to mount to round
tubbing. When mounting the bottom half of the clamps to
the Party Bar, you will need to use the 2 ea. 6mm X 12mm low
profile socket head cap screws. (6)
PR-URM
PR-FRC200
PR-FRC175
Use the 8mm X 12mm bolts (5) to attach
the mounting legs. Mounting legs (3) can
be installed in ether direction depending
on space constraints. When mounting with
opional clamps (PR-URM, PR-FRC200, and
PR-FRC175) use the hex bolts provided with
the clamps to mount the bottom half of the
clamps to the mounting legs.
PR-FRC200
PR-FRC175
PR-URM
2"-1.5" Clamp
1.75" Clamp
2.00" Clamp
Page 2
Aux Input Audio Output
Rev.7/06/2017 Pg. 3
Rev.7/06/2017 Pg. 2
Bluetooth module audio indicators:
Audio Response
Power on:
Power off:
Beep:
Beep:
Double Beep:
Module is turned on
Module is turned off
After LED light stops blinking means module is paired
When play/pause button is pressed and held means
module is unpaired from Bluetooth device.
When forward button is pressed and held means
module has reached maximum volume.
Description
Press: Next Song (FM Station)
Press & Hold: Volume Up
Switch 1 O n/Off
Remote switch buttons 2-4 are not used with this model
Switch aux. 12vdc (15 amp) ouput.
LED light status indicator:
LED Light Description
Led Mic.
Note: * When pressing for Power Off,be sure to hold until Power Off is indicated (audible). Failure to do so
may toggle the Bluetooth Receiver into AUX/BT Mode and it will remain in the last selected mode on subsequent Power On.
If this occurs, simply press the M button again to reselect BT, AUX or FM mode as desired. The receiver should automatically
pair with the last device in BT mode. To pair a new device, press and hold the Play/Pause button.
BPB24 / BPB24-DS
or BPB36
Installation Instructions
BPB24 / BPB24-DS
or BPB36
Installation Instructions
Bluetooth Mode:
Press: Play/Pause (Phone Answer/Hang Up)
Press & Hold: Unpair current Bluetooth device, then enter
pairing mode for new device.
FM Radio Mode:
Press: Auto Scan for stations available in the area.
AUX Mode:
Press: Mute Speaker
Press: Mode Select
(AUX, Bluetooth, FM Raido)
Press & Hold: Power OFF
Press: (if OFF) Power ON*
Press: Previous Song (FM Station)
Press & Hold: Volume Down
Auxiliary 12vdc output on/off switch.
Button1
Press to power on. Press while power is on to switch input among AUX,
Bluetooth and FM radio. Press and hold to power off.
Button2
Press to go forward one track/station. Press and hold to increase volume.
Button3
Press to play/pause. Press to answer/hang up phone. Double
press for last number radial or open Siri on Iphone. Press and
hold to unpair bluetooth device.
Button4
Press to go back one track/station. Press and hold to decrease volume.
Button5
Usedfora 1/8”audio cable
AUX Input
Used for line level audio signal output to an amplifier
Audio Output
Blinking: Bluetooth module is pairing
Solid Blue: Bluetooth module is paired
Blue/Red: AUX Input Mode
Fast Blinking: FM Radio Mode
Loading...