Page 1
BPB24 / BPB24-DS
BPB36
Installation Instructions
3 .
2.
1.
4.
11.
12.
5.
1. Party Bar (BPB24, BPB24-DS, or BPB36) 1 ea.
2. Optional Mounting Bolt 6mm 4 ea.
3. Mounting Leg 2 ea.
4. Rubber Vibration Insulation Pads 2 ea.
5. Socket Head Cap Screw 8mm X 12mm 2 ea.
6. Low Profile Socket Head Cap Screw 6mm X 12mm 2 ea.
7. Socket Head Cap Screw 6mm X 30mm 2 ea.
8. Narrow Washer 6mm 4 ea.
9. Nylon Insert Locking Nut 6mm 2 ea.
10. Stud 6mm x 40mm 2 ea.
11. Accessory Pigtail 1 ea.
12. Power Cable 6 ft. 1 ea.
7.
6.
8.
9.
10.
The internal RF circuit for the remote control will draw a small amount of current because it must always be ON
listening for the remote commands. Over time this could draw down your battery when your machine remains in
storage without being connected to a charger or not being actively used. For this reason, we recommend
connecting the Party Bar to a switched master power source or disconnecting the main power wire when the
machine is in storage. We also make a plug & play inline 12v master power switch that can be easily added to the
main battery wire for the Party Bar to completely kill power to the unit. It is listed under the Accessories tab on the
Party Bar product page on our website (Model number: PR-ILS16)
Remove fuse from 6 ft power cable (12). Attach the red wire to the positive battery terminal. Attach the black wire
to the negative battery terminal. Run power cable to the location of the BPB24. making sure power wire does not
hinder the safe operation of the vehicle. Plug the red power cable end into the BPB24’s red input power plug. The
black 12vdc accessory plug can be used to power any 12vdc accessory up to 15 amps. Use the included black
accessory pigtail (11) to wire your accessories.
IMPORTANT NOTICE:
Rev.12/12/2016 Pg. 1
Page 2
BPB24 / BPB24-DS
BPB36
Installation Instructions
Aux Input Audio Output
Button 1
Auxiliary 12vdc output on/off switch.
Button 2 Press and hold to power on, press while power is on to switch input
between aux. and Bluetooth inputs, Press and hold to power off.
Button 3 Press to go forward one track, Press and hold to increase volume.
Button 4
But ton 5
Press to play/pause, Press to answer/hang up phone, Double
press for last number radial or open Siri on Iphone, Press and
hold to unpair bluetooth device.
Press to go back one track, Press and hold to decrease volume.
Aux. Input Used for a 1/8” audio cable
Aud i o Out put Used for line level audio signal to an amplifier
Bluetooth module audio indicators:
Audio Response
Power on:
Power off:
Beep:
Beep:
Double Beep:
Description
Module is turned on
Module is turned off
After LED light stops blinking means module is paired
When play/pause button is pressed and held means
module is unpaired from Bluetooth device.
When forward button is pressed and held means
module has reached maximum volume.
Rev.12/12/2016 Pg. 2
Page 3
BPB24 / BPB24-DS
BPB36
Installation Instructions
Led Mic.
LED light status indicator:
LED Light Description
Blinking: Bluetooth module is pairing
Solid blue: Bluetooth module is paired
Blue/Red: Bluetooth module is in AUX
input mode
Sw itch 1 On/ O ff
Switch aux. 12vdc (15 amp) ouput.
Remote switch buttons 2-4 are not used with this model
Note: * When pressing for Power Off,be sure to hold until Power Off is indicated (audible). Failure to do so
may toggle the Bluetooth Receiver into AUX/BT Mode and it will remain in the last selected mode on subsequent Power On.
If this occurs, simply press the M button again to reselect BT or AUX mode as desired. The receiver should automatically pair
with the last device in BT mode. To pair a new device, press and hold the Play/Pause button.
Rev. 12/12/2016 Pg. 3
Page 4
BPB24 / BPB24-DS
BPB36
Installation Instructions
End Mounting Options
with Cast Aluminum Legs
See Warning Below!
PR-FRC200
PR-FRC175 1.75” Clamp
Use the 8mm X 12mm bolts (5) to attach
the mounting legs. Mounting legs (3) can
be installed in ether direction depending
on space constraints. When mounting with
opional clamps (PR-URM, PR-FRC200, and
PR-FRC175) use the hex bolts provided with
the clamps to mount the bottom half of the
clamps to the mounting legs.
2” Clamp
PR-URM 2” - 1.5” Clamp
Warning:
If you are using the cast aluminum mounting legs to secure the Party Bar to your machine, the mounting legs must
FIRST be attached and tightened to the Party Bar before mounting it to your machine. Attaching the legs to the
machine first and then inserting the Party Bar between them can cause misalignment, spacing, and torque issues
that can cause damage to the mounting assembly resulting in a failure.
”
Intergrated Mounting Rail Options
When using the Intergrated Mounting Rail System,
first determine your mounting stud spacing then screw
the 6mm X 40mm studs (10) into the mounting nuts. Mark
your desired spacing onto the flat surface to which you are
mounting. Use a 1/4” or 7mm drill bit to drill mounting holes.
Mount the Party Bar to your mounting surface using the 6mm
washers (8) and 6mm nylon locking nuts (9) provided in
hardware kit. You can also use our optional PR-URM, PR-FRC175,
and PR-FRC200 clamps (sold separately) to mount to round
tubbing. When mounting the bottom half of the clamps to
the Party Bar, you will need to use the 2 ea. 6mm X 12mm low
profile socket head cap screws. (6)
PR-URM 2” - 1.5” Clamp
PR-FRC200 2” Clamp
PR-FRC175 1.75” Clamp
Rev.12/12/2016 Pg. 4
Page 5
BPB24
Remote Pairing Instructions
Hold
Step 1. Remove the power from the BPB24 by unplugging
the main power cable. Wait 30 seconds
Red LED
Hold
Step 2. Press and hold the and
buttons. After 5 seconds you will see that
the red led on the remote will start to flash
slowly. Once the led is flashing release the
buttons
RFR-2
RFR-2
Press
Step 3. Plug the BPB24’s main power cable back in.
You will see the LEDs on the speaker flash white
3 times. Press and release the button. The
remote is now paired to the BPB24
Loading...