Bazooka BASE TUBE Installation And Troubleshooting Manual

TOYOTA FJ CRUISER

Southeast Toyota Distributors, LLC Page 1 of 9

Part Number: 00016-60009

2007- BASE TUBE (BAZOOKA®)

Accessor

y Code:

Kit Contents

Item # Quantity Reqd. Description
1 1 Bazooka Tube Assembly
2 1 Wire Harness
3 1 Hardware Bag
4 1 Care Card

Hardware Bag Contents

Item # Quantity Reqd. Description
1 4 4” Wire Ties
2 4 M6 X 30mm Bolts
3 2 M6 X 25mm Bolts
4 2 Main Plate w/ mounts
5 2 L- Mounting Plates
6 4 M6 X 30mm Bolts
7 2 Washers

Additional Items Required For Installation

Item # Quantity Reqd. Description
1

Conflicts

None

neral Applicability

Ge

All Toyota FJ Grades

Recommended Sequence of Application

Item # Accessory
1 Install Security/Audio
2 Install Bazooka Tube
3 Install Door Sills
4 Install Molded Dash

*Mandatory

Vehicle Service Parts (may be required for reassembly)

Ite

m # Quantity Reqd. Description

1

Bass Tube Specifications

Woofer Size 8”
Voice Coil Size

1”high power/high

mp.

te
Magnet Size 15 oz.
Frequency Response 39 – 85 hz.
Efficiency 105dB
Power Handling 100 watts
Dimensions 18.125” x 8.5” x 10”
Weight 14 lbs.
Impedance 2 ohms DVC

Recommended Tools

Personal

& Vehicle

Notes

Protection

Vehicle Protection Seat/Floor Covers
Part Protection Blankets

Special Tools Notes

Installation Tools Notes

Panel Removal Tool Nylon Removal Tool (NRT)
Socket/Ratchet 10mm
Socket Extension 6 inch
Torque Wrench 3 lbf·ft
Pliers 1. Diagonal Cutters

2. Long Nose (optional)

Screwdriver Magnetized Philips # 2

Special Chemicals

TOYOTA FJ CRUISER

Southeast Toyota Distributors, LLC Page 2 of 9

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.

These guidelines can be found in the "Accessory Installation Practices" document.

This document covers such items as:-

• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).

• Safety (eye protection, rechecking torque procedure, etc.).

• Vehicle Disassem bly/Reassem bly (panel removal, part storage, etc.).

• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).

Please see your Toyota dealer for a copy of this document.

1. Pre-installation Precautions

(a) Use Seat & Floor Protectors and Fender

STOP

Covers/Blankets to avoid damage to
surfaces. Operator Safety Warning (if
applicable.)

2. Battery Disconnect

STOP

(a) NOTE: Be sure to open the rear hatch,

PRIOR to disconnecting the battery.

(b) Remove the NEGATIVE (-) battery

terminal using a 10mm socket before any
disassembly starts. (Fig. 2-1).

3. Disassemble Center Rear Storage Area

(a) Remove Cargo Net Cleats using 10mm

Socket. Place in a safe location.

(b) Remove Side Trim Cover, Quarter Trim

STOP

Pocket, Quarter Trim Pocket Tray. (Fig.
3-2)

Fig 2-1

Fig 3-2

BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 3 of 9

4. Mount L-Brackets

(a) On wheel well, slide L-brackets under

side garnish ensuring no wires are
pinched. Insert Ground ring between
front L-bracket and vehicle. DO NOT
TIGHTEN AT THIS POINT! (Fig. 4-1)

NOTE: It may be necessary to unsnap
factory harness clip to align rear L-bracket.

5. Route Wire Harness

(a) Plug harness in at point shown. (Fig. 5-1)
(b) Route Wire harness as shown. (Fig. 5-2)
(c) Secure Wire harness at regular intervals

using 4” wire ties.

Fig. 4-1

Fig 5-1

(1) Fig. 5-2

BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 4 of 9

6. Install Main Plate

(a) Using the Cargo Cleats and the M6 x

35mm, loosely mount the top of the main
plate. DO NOT TIGHTEN AT THIS
POINT! See Fig 6-1.

(b) Route wiring harness through slot in

Main plate as shown. (Fig 6-2)

(c) Using two M6 x 20mm bolts and a

washer, bolt the lower points of the main
plate to the L-Brackets. DO NOT
TIGHTEN AT THIS POINT! (Fig. 6-3)

Fig 6-1

7. Tighten All Bolts

(a) Tighten bottom L-bracket bolts.
(b) Tighten Cargo cleat bolts.
(c) Tighten Main Plate bolts to L-brackets.

Fig 6-2

Fig 6-3

BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 5 of 9

8. Install Bass Tube

(a) Hang Bass Tube on Main Mounting

Plate as shown

(b) Using two M6 x 20MM bolts, tighten

down upper bolts as indicated in Fig 8-4.

(c) Plug Harness Connector into Bass Tube.

Fig 8-4

TOYOTA FJ CRUISER 2007 - BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 6 of 9

Checklist - these points MUST be checked to ensure a quality installation.

Check: Look For:

Accessory Function Checks

Turn on Radio

Veri

fy CD & Satellite Tuner (if equipped)

Antenna is functioning

Bazooka Tube operation

Vehicle Function Checks

Hazard Button

HVAC

Radio display turns on & sound is heard

CD player functions & Satellite Tuner

stations are playing (if equipped)

Reception

of AM/FM stations

Bazooka Tube – Listen to Bazooka Tube to

make sure it is functioning properly or by

feeling the Bazooka for vibration. Be sure

the

Phase Switch is in the “UP” position.

Functioning Hazard Lights

All HVAC controls function properly

Rear Window Defogger

Passenger Seat Belt Warning Light

Functioning Rear Window Defogger

Functioning Seat Belt Warning Light

TOYOTA 2007 - BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 7 of 9

Troubleshooting

Troubleshooting

Condition: Check For:

No sound from Bass Tube, however factory
speakers still play

1. Is the green L.E.D. lit on the Bass Tube?
If not, check for 12 volts on pins of the Bass
Tube Connector with the ignition on. If
either pin doesn’t indicate 12 volts, check T­Harness connectors behind the radio.

Distorted Sound

Low Sound

Rattling Noises

2. Is the 14-pin Molex connector securely
connected to the Bass Tube?

3. Is the ground ring securely fastened to the
rear center Anchorage bolt?

1. Close the back hatch of the vehicle

2. Adjust the radio to a comfortable listening
level, and then turn the “gain control” knob
on the Bass Tube counter-clockwise until the
sound becomes clean.

1. Close the back hatch of the vehicle

2. Adjust the radio to a comfortable listening
level, and then turn the “gain control” knob
on the Bass Tube clockwise until the sound
becomes audible. Do not adjust the level too
high, as this will result in distorted sound.

Rattling will be evident in some panels at
extreme volume conditions, but make sure
you have performed the following to
minimize noise:

1. Securely tightened Mounting Hardware so
Bass Tube Bracket does not move.

TOYOTA 2007 - BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 8 of 9

Troubleshooting

Troubleshooting

Condition: Check For:

Dimming Radio Lights

Radio does not come on

No Sound at all

Bass Tube produces sound on the right or
the left, but not both.

Dimming Radio Lights could occur when the
Bass Tube is played at high volumes.

Check to ensure that the main connector,
antenna connector, and auxiliary connector
have been correctly plugged back in.

1. Is the fuse under the hood still
operational?

2. Is the battery ground reconnected?

3. Is the radio connector securely seated?

Check T-Harness connections at the back of
the radio. All connectors must be securely
fastened to the correct wiring for both
channels to produce audio output.

TOYOTA FJ CRUISER 2007- BASS TUBE (BAZOOKA®)

Southeast Toyota Distributors, LLC Page 9 of 9

Wire Harness & Radio Wiring Schematics

Wire Harness & Radio Wiring Schematics

WIRING CONNECTOR SCHEMATICS:

Harness Split Radio Connector Subwoofer Connector

Harness Split Connector

Pin No. Wire Color Function

1 Red 12 Volt Battery Connection (B+)
2 White/Black Left Front Speaker (-)
3 Gray/Black Right Front Speaker (-)
4 Blue/White Remote Turn-On/Ignition (Switched+)
5 White Left Front Speaker (+)
6 Gray Right Front Speaker (+)

Subwoofer Connector

Pin No. Wire Color Function

1 Black Chassis Ground
2 N/A N/A
3 N/A N/A
4 N/A N/A
5 White Left Front Speaker (+)
6 Grey Right Front Speaker (+)
7 N/A N/A
8 Red 12 Volt Battery Connection (B+)

9 Blue/White Remote Turn-On/Ignition (Switched+)
10 N/A N/A
11 N/A N/A
12 White/Black Left Front Speaker (-)
13 Grey/Black Right Front Speaker (-)
14 N/A N/A

Radio Connector (R4 GRAY)

Pin No. Wire Color Function

1 Right Front Speaker (+)

2 Left Front Speaker (+)

3 NO CONNECTION NO CONNECTION

4 NO CONNECTION NO CONNECTION

5 12 Volt Ignition Switched (B+)

6 12 Volt Battery Connection (B+)

7 Right Front Speaker (-)

8 Left Front Speaker (-)

9 Chassis Ground (B-)
10 Power Antenna Control (+)
11 Power Antenna Control (-)
12

Dimmer / Illumination Control (B+ variable)