Date 2016-09-09 Rev. 0001-A Factory: ZHIFUR
Writing Desk
ITM. / ART. 1041240
Model # CSC48WD-1
ASSEMBLY INSTRUCTIONS
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please email your request to parts@baysidefurnishings.com and have
your instructions and parts list ready to provide the model name, part name or factory number. Or visit
our website www.baysidefurnishings.com
LOT NUMBER:
DATE PURCHASED: / /
2
1. This product is for indoor domestic use only.
2. Please read the Assembly Instructions prior to assembling this product.
3. To avoid damage, assemble the product on a non-abrasive surface such as a carpet surface.
4. Refer to your assembly manual for maximum weight capacities. Unload the drawer before moving the
furniture.
5. Do not push furniture, especially on carpeted floor. Have someone help you lift the item and place it in its
new location.
MANUFACTURER: Bayside Furnishings®
CATALOG: Writing Desk (CSC48WD-1)
MADE IN CHINA
GENERAL INFORMATION & TIPS
MAXIMUM RECOMMENDED WE IGHT LOADS
Please make sure you have all parts before beginning assembly. Please wait until all steps are completed
before tightening bolts. We recommend using two people for assembly.
MAXIMUM LOAD 13.6 kg / 30 lb
MAXIMUM LOAD 90.7 kg / 200 lb
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INS
TABILITY
, CAUSING POSSIBLE INJURY.
3
Parts and Hardware List
PART # PART DESCRIPTION PART FIGURE QUANTITY
A Desk Top
1
B
Leg
2
C Support
2
AA Bolt
12+1 extra
BB Lock Washer
12+1 extra
CC Flat Washer
8+1 extra
DD Camber Washer
4+1 extra
Hex-key Wrench
1
Tools required: Hex-key wrench (included).
4
Assembly Instructions
1. Place the desk top (A) upside down on a level and protective surface. Pull the drawer all the way forward
for the following steps (remove the drawer completely, if necessary).
2. Align and attach the legs (B) to the desk top (A) with eight bolts (AA) and eight washers (BB and CC).
3. Attach two supports (C) between the Desk Top (A) and the legs (B) by inserting four bolts (AA) with the
washers (BB and DD) through the drilled holes on the supports and screw into place.
A
B
B
B
A
A
B
AA
BB
CC
AA
BB
CC
A
B
B
C
C
AA
BB
DD
A
C
C
B
AA
BB
DD
5
Assembly Instructions
4. Ask for assistance to lift the unit upright and position it at the desired location.
5. If necessary, adjust the pre-attached floor levelers at the bottom of legs (B) to level the unit.
6. If you need to remove the drawer, please pull the drawer all the way out, then simultaneously push the
plastic release lever of the ball bearing slide up on one side and down on the other side, and then pull the
drawer completely out.
NOTE: To place the drawer back, simply push the ball bearing cart all the way to the end of the slides (in
both sides), and align the slide runners on the drawer with the slide tracks on the unit and push it carefully
inside until it stops. If the drawer does not go in smoothly, please take it out and repeat the step.
B
B
A
B
6
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Bayside Furnishings® purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Bayside Furnishings® product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
AUSTRALIA: Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
www.baysidefurnishings.com
MADE IN CHINA / FABRIQUÉ EN CHINE / HECHO EN CHINA
Retailer: Costco Wholesale UK Ltd,
UK Home Office, Hartspring Lane, Watford, Herts WD25 8JS
United Kingdom
01923 213113
Model: CSC40WD-1
Loading...