Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults are needed
to execute this action.
1
Page 2
LabelPictureDescriptionQTY
____
A
BLower Support Wings2
CTable Support Bar1
D
Long Legs with pre-attached
Support Wing.
Short leg ( for the Footrest
Shelf )
2
1
EFootrest shelf1
FBack panel1
GTable top1
HUpper Support Wings2
2
Page 3
LabelPictureDescriptionQTY
①
②
③
④
⑤
⑦
⑧
⑨
⑩
⑪
____
⑥
Short Bolt
(M6 x 35mm)
Long Bolt
(M6 x 55mm)
Long Screw (M6x45)9
Screw (M4 x 20mm)
(used with Screw Driver)
Nut Ø6 x 65
Plate for Horseshoe Bolt (125
x 15 x 2)
13
5
5
2
Horseshoe Bolt Ø6 x (110 +
106 + 110)
Restraint Strap2
Allen Key2
Spanner1
Screw DriverNot Provided
2
3
Page 4
Before Beginning Assembly:
____
OVERVIEW
Upper Suport Wing (H)
Back Panel (F)
Table Top (G)
Table Support Bar (C)
Lower Support Wing (B)
Long Legs (A)
Short Leg (D)
Footrest Shelf (E)
FRONT FACING
This Table has multiple parts and may require up to some 30 minutes to assemble. To give
you an overview of the Table, the above picture aims help you put the various parts into
perspective. Please read through the instructions here below to familiarise the parts and
steps before assembly.
Note : This table may be assembled by 1 to 2 persons.
4
Page 5
Step 1
____
Unpack and place all parts on a clean, non-marring surface.
Step 2
Customer need to check the railing height, matching to table height, before assembly of
Lower Support Wing (B).
Attached Long Legs ( A ) with pre- fixed wooden dowel to the Lower Support Wing (B) using
Short Bolt (②) and Allen Key (⑨).
Repeat the same process with the other Long Leg ( A )
DO NOT FULLY TIGHTEN THE BOLTS.
5
Page 6
Step 3
____
Customer need to check the railing height before assembly the part C.
Attached Table Support Bar ( C ) with Long Legs ( A ) using Short Bolt (①) and Allen Key
(⑨) as shown in picture.
Upon completion - place aside.
DO NOT FULLY TIGHTEN THE BOLTS.
Step 4
Using Screw Driver (⑪ ) and Screws (④) to assemble the Short Leg ( D ) to the Footrest
Shelf ( E ) as shown in picture.
Upon completion of assembly - place aside.
DO NOT FULLY TIGHTEN THE SCREWS
6
Page 7
Step 5
____
Lay down pre-fixed table in step 3
Assemble pre-fixed table in step 3 and step 4 together by using Long Bolts (②) and Allen
Key (⑨) as shown in picture.
DO NOT FULLY TIGHTEN THE BOLTS.
Step 6
Assembly the Table Top ( G ) to the Back Panel ( F ) by using Allen Key (⑨) to tighten the
Long Screws (③) in.
DO NOT FULLY TIGHTEN THE SCREWS.
7
Page 8
Step 7
____
Assembly Upper Support Wings (H) to finish part in Step 6 by using Long Screws (③) and
Allen Key (⑨) as shown in picture .
Upon completion - place aside.
DO NOT FULLY TIGHTEN THE SCREWS.
Step 8
With assistance from your adult partner, stand pre-fixed table in Step 5, right side up.
Attach the Table Support Bar (C) to your balcony (railing) by using Horseshoe Bolt (⑦), Plate
(⑥), Nut (⑤) and Spanner (⑩) as shown in picture.
Secure the Long Legs (A) to your balcony (railling) by using Restraint Strap (⑧) as shown in
picture.
DO NOT FULLY TIGHTEN THE NUTS.
8
Page 9
Step 9
____
Railing
Assemble pre-fixed table from Step 7 and Step 8 together by using Long bolts (②) and Allen
key (⑨) as shown in picture.
DO NOT FULLY TIGHTEN THE BOLTS.
Step 10
Railing
Next, place your arms onto the table top and EXERT pressure, floorwards.
This pressure will help all parts reach alignment at all joints.
Check for wobbles.
In a sequential manner, gradually tighten all Bolts/Screws until evenly secured.
Inspect the Table and make sure all parts are adequately connected.
Secure the Long Legs (A) to your balcony (railling) by using Restraint Strap (⑧) as shown in
picture.
This completes the entire assembly process and your table is ready for use.
This Table can only be used on a flat, level surface.
9
Page 10
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.