Caution : You must read this before you proceed
TABLE
CAUTION : This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults are needed
to execute this action.
1 ____
Label Picture Description QTY
A
Long Legs with pre-attached
Support Wing.
2
B Lower Support Wings 2
C Table Support Bar 1
D
Short leg ( for the Footrest
Shelf )
1
E Footrest shelf 1
F Back panel 1
G Table top 1
H Upper Support Wings 2
2 ____
Label Picture Description QTY
①
Short Bolt
(M6 x 35mm)
5
②
Long Bolt
(M6 x 55mm)
13
③
Long Screw (M6x45) 9
④
Screw (M4 x 20mm)
(used with Screw Driver)
5
⑤
Nut Ø6 x 6 13
⑥
Plate for Horseshoe Bolt (125
x 15 x 2)
2
⑦
Horseshoe Bolt Ø6 x (150 +
106 + 150)
2
⑧
Washer 9
⑨
Restraint Strap 2
⑩
Allen Key 2
⑪
Spanner 1
⑫ Screw Driver Not Provided
3 ____
This Table has multiple parts and may require up to some 30 minutes to assemble. To give
you an overview of the Table, the above picture aims help you put the various parts into
perspective. Please read through the instructions here below to familiarise the parts and
steps before assembly.
Note : This table may be assembled by 1 to 2 persons.
OVERVIEW
Before Beginning Assembly:
Long Legs (A)
Lower Support Wing (B)
Upper Suport Wing (H)
Table Top (G)
Footrest Shelf (E)
Short Leg (D)
Table Support Bar (C)
FRONT FACING
Back Panel (F)
4 ____
Step 1
Customer need to check the railing height, matching to table height, before assembly of
Lower Support Wing (B).
Attached Long Legs ( A ) with pre- fixed wooden dowel to the Lower Support Wing (B) using
Short Bolt (②) and Allen Key (⑩).
Repeat the same process with the other Long Leg ( A )
DO NOT FULLY TIGHTEN THE BOLTS.
Unpack and place all parts on a clean, non-marring surface.
Step 2
5 ____
Step 3
Step 4
Using Screw Driver (⑫ ) and Screws (④) to assemble the Short Leg ( D ) to the Footrest
Shelf ( E ) as shown in picture.
Upon completion of assembly - place aside.
Note: Adjust the Levelers to desired height to avoid wobble.
DO NOT FULLY TIGHTEN THE SCREWS
Customer need to check the railing height before assembly the part C.
Attached Table Support Bar ( C ) with Long Legs ( A ) using Short Bolt (①) and Allen Key
(⑩) as shown in picture.
Upon completion - place aside.
DO NOT FULLY TIGHTEN THE BOLTS.
6 ____
Step 6
Assembly the Table Top ( G ) to the Back Panel ( F ) by using Allen Key (⑩) to tighten the
Long Screws (③) in.
DO NOT FULLY TIGHTEN THE SCREWS.
Step 5
Lay down pre-fixed table in step 3
Assemble pre-fixed table in step 3 and step 4 together by using Long Bolts (②) and Allen
Key (⑩) as shown in picture.
DO NOT FULLY TIGHTEN THE BOLTS.
7 ____
Assembly Upper Support Wings (H) to finish part in Step 6 by using Long Screws (③) and
Allen Key (⑩) as shown in picture .
Upon completion - place aside.
DO NOT FULLY TIGHTEN THE SCREWS.
Step 8
Step 7
With assistance from your adult partner, stand pre-fixed table in Step 5, right side up.
Attach the Table Support Bar (C) to your balcony (railing) by using Horseshoe Bolt (⑦),
Plate (⑥), Washer, Nut (⑤) and Spanner (⑪) as shown in picture.
DO NOT FULLY TIGHTEN THE NUTS.
8 ____
Step 10
Step 9
Assemble pre-fixed table from Step 7 and Step 8 together by using Long bolts (②) and
Allen key (⑩) as shown in picture.
DO NOT FULLY TIGHTEN THE BOLTS.
Next, place your arms onto the table top and EXERT pressure, floorwards.
This pressure will help all parts reach alignment at all joints.
Check for wobbles.
In a sequential manner, gradually tighten all Bolts/Screws until evenly secured.
Inspect the Table and make sure all parts are adequately connected.
Secure the Long Legs (A) to your balcony (railling) by using Restraint Strap (⑨) as shown in
picture.
This completes the entire assembly process and your table is ready for use.
This Table can only be used on a flat, level surface.
9 ____
10 ____
Loading...