Page 1
Assembly Instruction Sheet
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electricaltape, safetyglasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.If any parts are missingor damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
(4)B10 Candelabra Base 60W Maximum.
30-45minutes
Identifyand inspect all parts beforebeginning installation. Check package contentlist and diagrams below tobe sure all parts are
Package Contents
Crossbar
A
x1
Lock Washer
B
x1
Hex Nut
C
x2
Nipple
D
x1
Lock Nut
E
x1
STEP 1 Assemble Side Arms-
A. Remove Hex Nut and Washer from the Side Arm (F). Attach the loop
end of the Side Arm (F) to the inside arm of the Fixture Body (G).
Pass the nipple at the top
end of the Side Arm (F)
through the hole on the
Ceiling Canopy. Place the
Washer back onto top end
of the SideArm (F) and by
using Spanner (H) thread
the Hex Nut onto the Side
Arm (F) to secure them
together. Hand tighten until
snug.
Figure 1
H
Ceiling
Canopy
G
Side Arm
Spanner
H
x1
F
x3
Fixture
Body
G
x1
Hex Nut
Washer
F
Loop
Inside
Arm
(Step 3 Continued)
B. Place the Ceiling Canopy of the Fixture
Body (G) over the Nipple (D) against the
ceiling to determine the correct position
of the Nipple (D). Thread the Lock Nut (E)
onto the Nipple (D). Adjust the Nipple (D)
to allow the Ceiling Canopy of the
Fixture Body (G) to rest against
the ceiling when held in place by
the Lock Nut (E).
C. Remove the Lock Nut (E) and the
Fixture Body (G). Tighten the Hex
Nut (C) against the Crossbar (A)
to secure in place.
D.RefertoStep4forwire
connections.
E. Place the Ceiling Canopy of the
Fixture Body (G) back over the
Nipple (D) and secure with the
Lock Nut (E). Hand tighten until
snug.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 3
Ceiling
Canopy
G
A
B
C
D
D
STEP 2 Install Crossbar-
A. A)Attach the Crossbar ( to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included) Tighten until snug..
Outlet Box
Green Ground
Screw
STEP 3 Install Fixture Body-
* Pliers is required for this step.
A. Thread Hex Nut (C) to the middle of the Nipple (D). Place Lock
Washer (B) over the Nipple (D) and then thread the Nipple (D) into
the Crossbar (A) until the Nipple (D) is about 0.375” above the
Crossbar (A).
A
Outlet Box Screw
(not included)
Figure 2
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 5 - Install Shade to Fixture
A. This fixture uses candelabra
bulb with screw base. Maximum
60 watts. Insert bulb and screw
snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
1of2
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Figure 5
Figure 4
Bulb
Socket
Page 2
FINISH: PALLADIAN BRONZE
(4) 60W Candelabra
Bulbs
Base
(Not Supplied)
PART NUMBER
PART NUMBER
NO.
1
1
REPLACEMENT PART
SHADE 1
5” Dia.
11. 5 ”
5”
15.75” Dia.
REQ.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
2of2
Loading...