Baumer VisiLine cameras User Manual
Product Specication
temperature
measurement point
Front View
Side View
Back View
Bottom View
C Mount
2 M3 depth 3
2 M3 depth 3
2 M2 depth 3
Pixel 0,0
2 M3 depth 3
4 M3 depth 3
8 7 8 715 6
20
9,3
3,5
26
14 5
48 3 9 6
33
33
26
12
3,5
8,6
26
26
30ø
VisiLine– Innovative functionality
Flexible assembly ▪
RGB and YUV interpolation algorithms on board ▪
Bandwidth up to 1000 Mbit/sec for fast multi-camera operation ▪
Flexible system architecture due to cable length up to 100 m ▪
Baumer driver for reliable image transfer ▪
PoE (Power over Ethernet) ▪
Dimensions
Quick Start Guide
VisiLine Gigabit Ethernet cameras
Latest software version and technical
documentation are available at:
www.baumer.com/vision/login
Safety
Conformity:
CE, FCC Part 15 Class B, RoHS
FCC – Class B device
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructios, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occure in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off an on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
support.cameras@baumer.com Phone +49 (0)3528 4386-0 Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH Badstrasse 30 DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany 02/14. v1.2 11107528
Safety Precautions
Notice
See User s Guide for the complete safety instructions!
Protect the sensor from dirt and ▪
moisture.
Avoid camera contamination by ▪
foreign objects.
Environmental Requirements
Storage temp. -10°C ... +70°C
Operating temp. see Heat Trans-
Humidity 10 % ... 90 %
Non-condensing
mission
Camera Type
Sensor
Size
Resolution
CCD Sensor (monochrome / color)
VLG-02M / VLG-02C 1/4" 656 x 490 160
VLG-12M / VLG-12C 1/3" 1288 x 960 42
VLG-20M / VLG-20C 1/1.8" 1624 x 1228 27
CMOS Sensor (monochrome / color)
VLG-22M / VLG-22C 2/3" 2044 x 1084 55
VLG-40M / VLG-40C 1" 2044 x 2044 29
System Requirements
Single-camera system Multi-camera system
Minimum Recommended Minimum Recommended
CPU
Clock
RAM
Operating
system
(OS)
Graphic
Ethernet
Framework
(optional)
Notice
Further technical details are
available in the respective
data sheet.
Intel® Pentium®4
or comparable
processor
2.5 GHz > 2.5 GHz 2.5 GHz 3 GHz
1024 MB 2048 MB 2048 MB > 2048 MB
Microsoft® Windows® XP incl. Service Pack 2 or higher
Intel® Core™ Duo comparable processor
Microsoft® Windows® XP x64 incl. Service Pack 2 or higher
Microsoft® Windows Vista™ 32 / 64 bit systems
Microsoft® Windows 7 32 / 64 bit systems
Linux® 32 / 64 bit systems from Kernel 2.6.xx
recommended resolution 1280 x 1024, color depth at least 16 bit
Gigabit Ethernet compliant NIC (recommended Intel® chipset)
Windows® OS: NET™ Framework 2 0 or higher
Linux® OS: Mono 1 2.4 or higher
Full Frames
[max. fps]
1
2
1
8
1
4
5
6
3
2
3
4
1
open wire
T
General Description
1
2
3
4
open wire
LED Signaling
Heat Transmission
Caution
Heat can damage the camera. Provide adequate dissipation of heat,
to ensure that the temperature does not exceed he value in the table
below.
As there are numerous possibilities for installation, Baumer does not
specify a specic method for proper heat dissipation.
No. Description No. Description
1 C-Mount lens connection 4 Power supply / Digital-IO
2 Ethernet Port
3 Digital-IO
Data Interface / Power Supply / Digital IOs
Notice
The VisiLine supports PoE (Power over Ethernet) IEEE 802.3af Clause 33, 48 V
power supply.
8P8C mod jack with LEDs
1 green/white MX1+ (negative / positive V
2 green MX1- (negative / positive V
3 orange/white MX2+ (positive / negative V
4 blue MX3+
5 blue/white MX36 orange MX2- (positive / negative V
7 brown/white MX4+
8 brown MX4-
Power supply / Digital-IO
wire colors of the connecting cable
)
port
)
port
)
port
)
port
LED Signal Meaning
green Link active
1
green ash Receiving
2 yellow Transmitting
Installation
Installation of the camera:
Connect the camera using an ▪
appropriate cable (at least Cat-5e)
to he GigE board on your PC.
If required, connect a trig- ▪
ger and / or flash to process
interface.
Installation sample
Connect the camera to power supply. ▪
1 - PCI board; 2 - GigE cable;
3 - Power cable / Digital-IO; 4 - Digital-IO
Installation of cameras with PoE:
Connect the camera using an appropriate cable (at least Cat-5e) to a free port of a ▪
PoE capable ethernet switch.
Establish the connection between switch and GigE board on your PC. ▪
If required, connect a trigger and or flash to process interface. ▪
Measure Point Maximal Temperature
T 50°C (122°F)
1 Power V
2 IN 1 white 3 OUT 2 blue
3 GND blue 4 OUT 3 black
4 OUT 1 black
5 U
6 GND IN pink
OUT grey
ext
brown 1 not used brown
CC
Notice
The electrical data are available in he
respective data sheet.
Installation sample
1 - PCI board;
2 - GigE cable;
3 - PoE capable ethernet switch
or Baumer PoE components;
4 - Cable for trigger and ash
Loading...