Baumer HXG User Manual
Product Specication
open wire
36
26
26
36
16 x M 3 de pt h 6
UN C 1/ 4-20
52
52
26
36
55
5
12, 5
10
52
52
26
36
UNC 1/ 4 - 2 0
26
36
16x M3 d eph 5
26
36
54 , 7
open wire
4
5
4
HXG cameras – Maximum Performance with CMOSIS sensors
Dual Gigabit Ethernet progressive scan CMOS camera ▪
Binning, subsampling, true partial scan function (ROI) for increased frame rates ▪
High Dynamic Range (HDR) image acquisition ▪
External synchronization via industrial compliant process interface (trigger / flash) ▪
Global shutter architecture for minimized motion blur ▪
Power over Ethernet support ▪
Standard RJ45 connectors ▪
GigE Vision ▪
TM
standard compliant
Excellent image quality ▪
Camera parameter programmable in real-time ▪
Frame rates up to 105 fps (HXG20 / Monochrome) ▪
Dimensions
● HXG (C-Mount version)
Quick Start Guide
HXG cameras with CMOS sensors (Release 2)
Latest software version and technical
documentation are available at:
www.baumer.com/vision/login
Safety
Conformity:
CE, FCC Part 15 Class A, RoHS
FCC – Class A device
No t e : This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
support.cameras@baumer.com· Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany v1.6 07/13. 11086858
Safety instructions
Notice
See User´s Guide for the complete safety instructions!
Protect the sensor from dirt and ▪
moisture.
Never open the camera housing. ▪
Avoid camera contamination by ▪
foreign objects.
Environmental requirements:
Storage temp. -10°C ... +70°C
Operating temp. +5°C ... +50°C
Housing temp. max. +50°C
Humidity 10 % ... 90 %
non-condensing
Camera Type
Sensor
Size
Resolution
Full Frames
[max. fps]
Monochrome
HXG20 2/3“ 2048 x 1088 105 337
HXG20NIR 2/3“ 2048 x 1088 105 337
HXG40 1“ 2048 x 2048 56 180
HXG40NIR 1“ 2048 x 2048 56 180
Color
HXG20 2/3“ 2048 x 1088 105 337
HXG40 1“ 2048 x 2048 56 180
Installation
Installation sample without PoE
1 - network interface card
2 - network cable
3 - Process interface cable
4 - Power cable
Installation sample with PoE via NIC
1 - PoE network interface card (NIC)
2 - network cable (PoE)
3 - network cable (without PoE)
4 - Process interface cable
Installation sample with PoE via Injector
1 - network interface card (NIC)
2 - network cable (without PoE)
3 - Injector
4 - network cable (with PoE)
5 - Process interface cable
Burst Mode
(buffered)
Dimensions
● HXG-F (F-Mount version)
1
2
3
General Description
1
2
3
4
56
T T
LED2
LED1
81
LED2
LED1
81
1
4
3
8
5
7
3
1
4
2
6
LED Signaling
Heat Transmission
Caution
Provide adequate dissipation of heat, to ensure that the temperatures does not exceed +50°C (+122°F).
The surface of the camera may be hot during operation and immediately after use. Be careful when handling the camera and avoid
contact over a longer period.
It is very important to provide adequate dissipation of heat, to ensure that the housing
temperature does not reach or exceed +50°C
(+122°F). As there are numerous possibilities for
installation, a specic method for proper heat dissipation is not dened, but the following principles
are suggested:
No. Description No. Description
1 (respective) lens mount 4 Digial-IO
2 Power Supply 5 Data Port 2
3 Data Port 1 6 Signaling-LED
Data Interfaces
Data / Control
1000 Base-T (Port 1)
1 green/white MX1+ 1 green/white MX1+
2 green MX1- 2 green MX13 orange/white MX2+ 3 orangeg/white MX2+
4 blue MX3+ 4 blue MX3+
5 blue/white MX3- 5 blue/white MX36 orange MX2- 6 orange MX27 brown/white MX4+ 7 brown/white MX4+
8 brown MX4- 8 brown MX4-
Notice
Data port 1 supports Power over Ethernet (38 VDC .. 57 VDC).
For the data transfer, the ports are equal. For Single GigE connect one port and
for Dual GigE connect the second port additionally. The order does not matter.
wire colors of the connecting cable
Data / Control
1000 Base-T (Port 2)
LED Signal Meaning
1
green
green ash
Link active
Receiving
2 yellow Transmitting
3
green
yellow
Power On
Readout active
Power Supply and Process Interface
Power Supply Digital I/O
wire colors of the connecting cable
1 brown Power V
3 blue GND 2 brown Line 1
4 black not used 3 green Line 0
CC
M8 / 8 pins
1 white Line 5
4 yellow GND
5 grey U
6 pink Line 3
7 blue Line 4
8 red Line 2
Power Supply
Power V
CC
20 VDC ... 30 VDC
Operate the cameras only in mounted condition ▪
with a good heat conductor (e.g. aluminum)
Mounting in combination with forced convection ▪
T: Housing temperature
may provide proper heat dissipation
measurement point
ex
Loading...