Baumer HXC User Manual
52
52
26
26
36
36
UN C 1/ 4- 20
16 x M3 d ept h 6
26
36
36
36
4 x M3 depth 6
37, 4
52
52
26
26
3636
UN C 1/4- 20
16 x M 3 de pt h 6
26
36
37
Product Specication
HXC cameras - Maximum Performance with CMOSIS sensors
Camera Link ▪
®
Full progressive scan CMOS camera
Excellent image quality ▪
Global shutter architecture for minimized motion blur ▪
Low noise due to correlated double sampling (CDS) ▪
HDR (High Dynamic Range) ▪
Enhanced NIR sensitivity model available ▪
Binning, subsampling and true partial scan function (ROI) for increased frame ▪
rates
External synchronization via industrial compliant process interface (trigger / flash) ▪
Integrated supplementary function for flexible integration ▪
Integrated 256 MByte RAM for temporarily image data buffering ▪
Two standard 26 pin Mini-CameraLink ▪
Support for CameraLink ▪
®
Base, Medium, Full and 10 tap configurations
®
connectors
Baumer GAPI: Flexible, generic software interface for Windows ▪
Dimensions HXC20/40 F-Mount
Quick Start Guide
HXC cameras – Release 2 (Camera Link®)
Latest software version and technical
documentation are available at:
www.baumer.com/vision/login
Safety
Conformity:
CE, FCC Part 15 Class B, RoHS
FCC – Class B device
No t e : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
support.cameras@baumer.com· Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed cannot be guaranteed.
Subject to change without notice. Printed in Germany 06/14. v1.7 11054752
Safety instructions
Notice
See User´s Guide for the complete safety instructions!
Protect the sensor from dirt and ▪
moisture.
Never open the camera housing. ▪
Avoid camera contamination by ▪
foreign objects.
Environmental requirements:
Storage temp. -10 °C ... +70 °C
Operating temp. +5 °C ... +60 °C
Housing temp. max. +65 °C
Humidity 10 % ... 90 %
(14 °F...158 °F)
(41 °F...140 °F)
(max. 149 °F)
Non-condensing
Camera Type
Sensor
Size
Resolution
Full Frames
[max. fps]
Monochrome
HXC20 2/3“ 2048 x 1088 337
HXC40 1“ 2048 x 2048 180
Color
HXC20c 2/3“ 2048 x 1088 337
HXC40c 1“ 2048 x 2048 180
Installation
Dimensions HXC20/40 C-Mount
Installation using
Camera Link® BASE:
Connect the camera using ▪
an appropriate cable to the
framegrabber board on your
PC using the lower sdr-26
jack on the camera side
If required, connect a strobe ▪
to the connector
Connect the camera to ▪
power supply
Installation sample
1 - Framegrabber board; 2 - CameraLink® cable;
3 - Process interface cable; 4 - Power cable
Installation using
Camera Link
®
MEDIUM /
FULL:
Connect the camera using ▪
two appropriate cables to
the framegrabber board on
your PC (this configuration
requires the BASE and the
FULL Camera Link
®
line)
If required, connect a strobe ▪
to the connector
Connect the camera to ▪
power supply
Installation sample
1 - Framegrabber board; 2 - CameraLink® cable;
3 - Process interface cable; 4 - Power cable
Ba u me r
Type: HXCXXx (xxxxxxx)
S/N: 000XXXXX
R1.0
CL FULL
CL BASE
C
L BASE
C
L FUL
L
2
1
1
4
3
8
5
7 3
1
4
2
6
T T
General Description
1
2
3
4
56
No. Description No. Description
1 (respective) lens mount 4 Digital-IO supply
2 Power supply 5 CameraLink
3 CameraLink
®
Full socket 6 Signaling-LED
®
Base socket
LED Signaling
LED Signal Meaning
green Power on
1
yellow Readout active
green Transmitting
2
red (yellow in both)
Conguration comman
processing
Heat Transmission
Caution
Provide adequate dissipation of heat, to ensure that the temperature
does not exceed the spedied temperature.
The surface of the camera may be hot during operation and immediately after use. Be careful when handling the camera and avoid
contact over a longer period.
T: Housing temperature
measurement point
It is very important to provide adequate dis-
sipation of heat, to ensure that the housing
temperature does not reach or exceed +65 °C
(+149°F). As there are numerous possibilities for
installation, a specic method for proper heat dis-
sipation is not dened, but the following principles
are suggested:
Operate the cameras only in mounted ▪
condition with a good heat conductor
(e.g. aluminum)
Mounting in combination with forced ▪
convection may provide proper heat
dissipation
Camera Link® Interfaces
Notice
The camera has two CameraLink sockets. To differentiate between CameraLink Base and CamerLink Full socket, please look
at the label. You can not use the CL Full socket alone!
Caution
When xing the CameraLink® cable with too much force the
screws might get damaged.
The maximum torque is 2.5 inch lbf [0.3 Nm].
Base Camera Link
Pin Signal Pin Signal Pin Signal Pin Signal
1 GND 14 GND 1 GND 14 GND
2 X0- 15 X0+ 2 Y0- 15 Y0+
3 X1- 16 X1+ 3 Y1- 16 Y1+
4 X2- 17 X2+ 4 Y2- 17 Y2+
5 XCLK- 18 XCLK+ 5 YCLK- 18 YCLK+
6 X3- 19 X3+ 6 Y3- 19 Y3+
7 SERTC+ 20 SERTC- 7 100 Ω term. 20 100 Ω term.
8 SERTFG- 21 SERTFG+ 8 Z0- 21 Z0+
9 CC1- 22 CC1+ 9 Z1- 22 Z1+
10 CC2+ 23 CC2- 10 Z2- 23 Z2+
11 CC3- 24 CC3+ 11 ZCLK- 24 ZCLK+
12 CC4+ 25 CC4- 12 Z3- 25 Z3+
13 GND 26 GND 13 GND 26 GND
®
Full Camera Link
Power Supply / IO Pin Assignment
Caution
A power supply with electrical isolation is required for proper operation of the camera. Otherwise the device may be damaged.
M8 / 3 pins M8 / 8 pins
wire colors of the connecting cable
®
1 (brown) Power V
CC
3 (blue) GND 2 (brown) Line 1
4 (black) NC 3 (green) Line 0
Power Supply
Power VCC 9,6 VDC .. 30 VDC
I 200 mA .. 625 mA
1 (white) Line 9
4 (yellow) GND
5 (grey) U
ext
6 (pink) Line 7
7 (blue) Line 8
8 (red) Line 2
Loading...