Page 1
SUPREMA1W/SS
DISHWASHER
Page 2
BAUM
ATIC SUPREMA1W/SS dishwasher user manual
1
IMPORTANT!
BAUMATIC
INSTRUCTION MANUAL
CAREFULLY READING IT BEFORE USING THE DISHWASHER WILL HELP
YOU
USE AND MAINTAIN THE DISHWASHER PROPERLY.
DD 02/11/0707
1
SUPREMA1W/SS – DISHWASHER
60CM FULL HEIGHT DISHWASHER
PLEASE
READ THIS MANUAL AND KEEP IT FOR FUTURE REFERENCE!
THIS MANUAL CONTAINS SECTIONS OF SAFETY INSTRUCTIONS,
OPERATING
INSTRUCTIONS
&
TROUBLESHOOTING TIPS,
ETC.
Page 3
MINIMUM AND MAXIMUM PLATE SIZES..30
ENVIRONMENTAL NOTE………………………31
CONTACT DETAILS……………………………..32
FINAL CHECKLIST BEFORE STARTING…….29
HOW TO INSTALL ……….…….…..……....24-29
BAUMATIC SUPREMA1W/SS dishwasher user manual
2
FROM PROFESSIONAL
WITHOUT GIVING PRIOR
2
PLEASE NOTE:
THE MANUFACTURER
RESERVES THE RIGHT TO MAKE
MODIFICATIONS
TO
PRODUCTS
NOTICE.
BEFORE CALLING
FOR
SERVICE
REVIEWING THE SECTION ON
TROUBLESHOOTING
TIPS WILL
HELP
YOU SOLVE SOME
COMMON
PROBLEMS WITHOUT
THE
NEED TO ASK FOR HELP
TECHNICIANS.
CONTENTS
• SAFETY FIRST!
SAFETY INFORMATION .……………..…………3
*Please read this before using your dishwasher!
• KNOWING YOUR
DISHWASHER
CONTROL PANEL ………………………..……..…4
DISHWASHER FEATURES …………..………….4
• USING YOUR
DISHWASHER
WATER SOFTENER …………………..………...5-6
DETERGENT ………………..............................6
RINSE AID ………………….............................7
LOADING YOUR DISHWASHER…..….......8-11
STARTING A WASH CYCLE ……………….12-14
UNLOADING AT THE END OF A CYCLE…....14
FILTERING SYSTEM ………………..…….…….15
CLEANING AND MAINTAINING
YOUR DISHWASHER …………………….…15-17
• BEFORE YOU CALL FOR
SERVICE…
TROUBLESHOOTING
………………….…18-21
ERROR CODES ………………………………….…22
• MISCELLANEOUS
CHARACTERISTICS ………….………….……...23
Page 4
AFTER USE
2) Load sharp knives with the handles up to prevent
ONLY USE AUTOMATIC DISHWASHER
AFTER COMPLETION OF WASH CYCLE.
NEVER USE SOLVENTS AS THIS COULD RESULT IN AN
DISCONNECT THE WATER SUPPLY (SEE PP. 17, 26).
BAUMATIC SUPREMA1W/SS dishwasher user manual
3
IMPORTANT SAFETY INFORMATION
READ
BEFORE USING!
ON ITS DOOR OR DISH RACKS – TIPPING
•
KEEP CHILDREN AWAY FROM DETERGENT,
DISHWASHER AS THERE COULD BE
COMPARTMENT OF YOUR OLD APPLIANCE
BEFORE USING
SOME ITEMS ARE UNSUITABLE FOR WASHING
IN YOUR DISHWASHER. PLEASE SEE PAGE 8 FOR A LIST
OF
THESE ITEMS.
DO NOT TAMPER WITH THE CONTROLS.
WHEN LOADING ITEMS TO BE WASHED:
1) Keep sharp items like knives away from the door
seal.
injuries.
•
ALWAYS KEEP THE DOOR CLOSED TO AVOID DANGER
OF TRIPPING.
DETERGENT, NOT SOAP OR LAUNDRY DETERGENT.
•
CHECK THAT THE DETERGENT DISPENSER IS EMPTY
EXPLOSION!
•
IF LEAVING UNUSED FOR A LONG TIME,
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY BEFORE
USING
YOUR DISHWASHER FOR THE FIRST TIME!
3
DURING USE
ELECTRICAL SAFETY
• NOTE - This appliance must be grounded. In
the event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
of electrical current. You will be able to tell if
it is because a non-grounded appliance will
give off an electrical discharge.
• Manufacturer declines all responsibility for
any damage due to non-grounding of
appliance.
• DURING THE GUARANTEE PERIOD ONLY BAUMATIC
SERVICE ENGINEERS OR AN AUTHORISED AGENT
OF BAUMATIC SHOULD CARRY OUT REPAIRS ON
THIS UNIT.
• DO NOT USE IF THE SUPPLY CORD IS DAMAGED.
• FOR INSTALLATION PROCEDURE PLEASE CONSULT
PAGES 24 – 29.
CHILD SAFETY
•
DO NOT ABUSE OR FORCE THE
DISHWASHER.
DO
NOT SIT ON OR STAND
HAZARD.
RINSE AID AND THE OPEN DOOR OF THE
DETERGENT LEFT INSIDE.
•
SUPERVISE YOUNG CHILDREN TO ENSURE
THEY
DO
NOT PLAY WITH THE APPLIANCE.
•
SUPERVISE INFIRM PERSONS IF THEY MUST
USE
THE APPLIANCE.
•
REMOVE THE DOOR TO WASHING
BEFORE DISCARDING IT.
•
DO NOT USE YOUR DISHWASHER UNLESS
ALL
ENCLOSURE PANELS ARE PROPERLY
IN
PLACE. OPEN THE DOOR VERY
CAREFULLY
IF
THE DISHWASHER IS
OPERATING.
THERE IS A RISK OF WATER
SQUIRTING
OUT.
•
DO NOT TOUCH THE HEATING ELEMENT
DURING OR IMMEDIATELY AFTER USE.
Page 5
B
AUMATIC SUPREMA1W/SS dishwasher use
r
manu
al
4
CONTROL PANEL
1
2
3
4
5
6
7
8
9
10
Display Window:
Time remaining in Program; delay time; running indicator; temperature of water; fault codes, etc.
Program Indicator Light.
Power On Indicator Light: Comes on when the power is turned on.
Power Switch:
Turns the power supply on /off.
Start / Pause Button: Press this button to start or stop the dishwasher.
Program Button: Press this button to select the program you want to run.
Door Lock:
Pull it to open the door.
Delayed Start Button: Press this button to set the delayed hours for washing.
Rinse Aid Warning Light: Add more rinse aid as the indicator on the front panel lights up (Certain Models only).
Salt Warning Light:
Add more salt as the indicator on the front panel lights up.
WARNING – BEWAR
E
OF
HOT WATER & STEAM AS YOU OPEN TH
E
DOOR!
DISHWASHER FEATUR
ES
1
2 3 4
Adjustable Upper Basket
Spray Arms
Lower Basket
Water Softener
5
6 7
8
Main Filter
Detergent Dispenser
Cup Shelf
Cutlery basket
9 Coarse Filter
10
Rinse Aid Dispenser
11 Drain Pipe Connector
12
Inlet Pipe Connector
4
Page 6
DISHWASHER.
SURE NOT TO ADD SALT AND/OR RINSE AID
TO
THE APPLIANCE AS THESE TABLET
MINERALS FROM THE WATER
.
INDIVI
DUAL CHEMICALS AND MAY
CAU
SE
BAUMATIC SUPREMA1W/SS dishwasher user manual
5
Note on chemicals used by the dishwasher
•
Your dishwasher is equipped with an adjustable rinse aid and salt container. Using individual detergents,
rinse
aid and salt will give the best possible results as this will give the correct dosage of each chemical to
suit
your needs.
Using Two-in-One or Three-in-One tablets may not give the best results when used in
your
appliance, and may not be suitable for the type of water supply in your home, as they contain pre-
determined
quantities
of
salt,
rinse
aid
and
detergent
and
cannot
be
adjusted
to
the
individual
requirements.
If you are going to use 3-in-1 (or 2-in-1) tablets, we suggest that you contact the manufacturer before use
or if you experience poor results in the wash performance and ask for assistance from them.
WARNING!
ONLY USE DISHWASHER SALT IN YOUR
NOTE:
IF YOU USE 3-IN-1 OR 2-IN-1 TABLETS, BE
TYPES ALREADY CONTAIN SALT AND/OR
THE LIME IN HARD WATER MAKES DEPOSITS FORM ON
RINSE AID. A
DDING SALT AND RINSE AID
DISHES AND UTENSILS. YOUR DISHWASHER HAS A
TO YOUR
DISHWASHER’S COMPARTMENTS
SPECIAL SOFTENING FEATURE THAT USES SALT
IN A CYCLE INVOLVING A 3-IN-1 OR 2-IN-1
SPECIFICALLY DESIGNED TO ELIMINATE LIME AND
TABLET WILL RESULT IN
OVERDOSING OF
OVERFLOWING OF WATER
AND SUDS.
LOADING SALT INTO THE SALT CONTAINER
• REMOVE THE LOWER BASKET & THEN
UNSCREW
AND REMOVE THE CAP
FROM
THE SALT CONTAINER.
• IF YOU ARE FILLING THE CONTAINER
FOR
THE FIRST TIME, FILL WITH
APPROX.
1
LITRE OF WATER.
• PLACE THE END OF THE SUPPLIED
FUNNEL INTO THE HOLE & ADD 1.2 Kg
OF SALT. NOTE: IT IS NORMAL FOR A
SMALL AMOUNT OF WATER TO COME
OUT OF THE CONTAINER.
5
WATER
SOFTENING
FEATURE
Page 7
BAUMATIC SUPREMA1W/SS dishwasher user manual
6
SETTING THE WATER SOFTENER LEVEL
YOU CAN ADJUST THE AMOUNT OF SALT USED BY THE DISHWASHER TO SOFTEN WATER TO GET
THE BEST WASHING RESULTS, BASED ON THE HARDNESS OF WATER IN YOUR AREA.
2 THERE IS A RING ON THE NECK OF THE
CONTAINER.
ROTATE THE RING IN AN
ANTICLOCKWISE
DIRECTION FROM THE “-”
SETTING
TOWARDS THE “+” SETTING
ACCORDING
TO
THE HARDNESS OF WATER
IN
USE.
SEE TABLE BELOW.
NOTE
1. THE SALT CONTAINER MUST BE REFILLED WHEN THE
SALT
WARNING LIGHT COMES ON. ALTHOUGH THE
1 UNSCREW THE CAP FROM THE SALT
CONTAINER.
SALT CONTAINER MAY BE FULL, THE INDICATOR LIGHT
MAY NOT GO OUT UNTIL THE SALT HAS DISSOLVED.
2. IF THERE ARE SALT SPILLS, A SOAK PROGRAM CAN
BE
RUN TO WASH AWAY SPILLAGE BEFORE USING THE
MACHINE.
3. CLEAR ANY SALT GRANULES AWAY FROM THE
CONTAINER OPENING.
ADJUSTMENTS SHOULD BE MADE ACCORDING TO THE TABLE BELOW:
WA TE R H
ARDN ESS
( c ycles/
1 .2kg s)
Au t
o no my
Salt c
on sum pti on
Se l ect or Pos iti
o n
(
g ra m/cycl e)
Cl a rke Degr e es
mmol /l
dH
/
0~
14
0~
18
0~ 1.
8 0
/
-
14 ~3 6 18 ~4 4 1 . 8~ 4.4 20 60
36~71 44~89 4. 4~ 8.9
M ED
40 30
Co nt a ct your l oca l wa t er boa rd f or inf or ma ti on on the ha rdne ss o f you r w ate r sup pl y.
+
71 89
8.
9 60 20
“
How much do I use?”
DETERGENT
To OPEN the DETERGENT DISPENSER DOOR, use the CATCH on its LOWER SIDE.
*NOTE: SEE P.13 – WASH CYCLE TABLE for AMOUNT of DETERGENT to use.
NOTE:
• ALWAYS CHECK THE WASH CYCLE TABLE
FOR DOSAGE ADVICE. NEVER OVERFILL
THE DISPENSER.
• DO NOT OVERDOSE TO PREVENT THE
FORMATION OF DEPOSITS (THE WATER
SOFTENING FEATURE ALREADY TAKES CARE
OF THIS!).
THE HARDER YOUR WATER, THE MORE DETERGENT
YOU MAY NEED. ADJUST THE DOSE JUST BY SMALL
AMOUNTS UNTIL YOU FIND THE CORRECT AMOUNT
OF DETERGENT TO USE.
6
Page 8
BAUMATIC
FORMING DROPLETS ON YOUR DISHES
THAT CAN CAUSE SPOTS AND STREAKS. IT
DAMP CLOTH. DON’T FORGET TO REPLACE
THE ‘OPEN’ (LEFT) ARROW AND LIFT IT OUT.
• POUR THE RINSE AID INTO THE DISPENSER.
DISHWASHER DOOR.
‘OPEN’ ARROW & TURN IT TO THE CLOSED
aid level indi
cator changes, as illustrated below.
SUPREMA1W/SS dishwasher user manual
7
• THE RINSE AID IS RELEASED DURING THE
FINAL RINSE TO PREVENT WATER FROM
RINSE AID
ALSO IMPROVES DRYING BY ALLOWING
WATER TO FALL OFF THE DISHES.
• YOUR DISHWASHER IS DESIGNED TO USE
LIQUID
RINSE AIDS. THE RINSE AID
DISPENSER
CAN BE FOUND INSIDE THE
DOOR NEXT TO THE DETERGENT
DISPENSER. TO FILL THE DISPENSER, OPEN
THE CAP AND POUR THE RINSE AID INTO
THE DISPENSER UNTIL THE LEVEL
INDICATOR TURNS COMPLETELY BLACK.
THE DISPENSER HOLDS ABOUT 100ML OF
LIQUID RINSE AID.
• BE CAREFUL NOT TO OVERFILL THE
DISPENSER – THIS COULD CAUSE
• TO OPEN THE DISPENSER, TURN THE CAP TO
FROTHING. WIPE AWAY SPILLS WITH A
THE CAP BEFORE YOU CLOSE THE
BE CAREFUL NOT TO OVERFILL.
NOTE: IF
YOU HAVE SOFT WATER, YOU MAY NOT
• REPLACE CAP BY INSERTING IT ALIGNED WITH
NEED RINSE AID FOR IT MAY CAUSE A WHITE FILM
(RIGHT) ARROW.
TO DEVELOP ON YOUR DISHES.
ADJUSTING THE RINSE AID DISPENSER
As with detergent, the amount of ri
nse
ai
d needed
for your di
shes depends on
the
hardness of the w
ater in
your area.
Too
much rinse aid can result in
foaming
and cause cloudiness or
streaks
on
your dishes. If
your water
is
very soft, you may not
need rinse
aid.
You can always dilute the rinse
aid
with an
equal amount of
water.
The rinse aid dispenser has six settings. ALWAYS START WITH THE DISPENSER SET ON “1”. IF SPOTS & POOR
DRYING ARE A PROBLEM, INCREASE THE AMOUNT OF RINSE AID DISPENSED BY REMOVING THE DISPENSER
LID AND ROTATING THE DIAL TO “2”. IF THE DISHES ARE STILL NOT DRYING PROPERLY OR ARE SPOTTED,
ADJUST THE DIAL TO THE NEXT HIGHER NUMBER UNTIL YOUR DISHES ARE SPOT-FREE.
***
NOTE:
Please read the
notes
for deter
gent
use on p. 13.
WHEN TO REFILL THE RINSE
As the rinse aid diminishes, the size of the black dot on the rinse
AID DISPENSER
-
If the rinse aid
Full
warning light (
SEE
control panel) is not on, you
3 / 4 full
can judge the rinse aid level by looking at the
1 / 2 full
black dot on the rinse aid dispenser. As the
1 / 4 full - S
hould refill to eliminate spo
tting
rinse aid level decreases, the black dot shrinks.
Empty
Never let the rinse aid get below ¼ full.
7
Page 9
BAUMATIC SUPREMA1W/SS dishwasher user manual
8
LOADING
NOTE:
YOUR
FOR
BEST PE
RFORMA
NCE,
FOLLOW TH
ESE
L
O
ADING GUIDELINES. FEATURES AND
APPEARA
NCE OF
RACKS & C
UTLERY
BASKETS
MAY VARY
FROM YOUR MODEL.
DISHWASHER
BEFORE LOADING!
• REMOVE ALL SCRAPS OF FOOD.
• E
MPTY DRINKS & LIQUIDS FROM CUPS.
• SOFTEN BURNT-ON FOOD IN PANS BY
SOAKING.
DO T N YOUR DISHWASHERNO PUT THESE ITEMS I :
•
BRONZE
•
OLDER
•
STEEL ITEMS
CUTLERY
CUTLERY
SUBJECT TO
WITH GLUED
RUSTING
•
SAUCEPANS
PARTS
WITH
•
WOODEN
WOODEN
PLATTERS
HANDLES
•
BONDED
CUTLERY
•
CUTLERY
ITEMS OR
•
ITEMS MADE
WITH
DISHES
FROM
WOODEN,
SYNTHETIC
HORN, CHINA
FIBRES (eg.
OR MOTHER
•
PEWTER OR
SPONGES)
OF PEARL
COPPER ITEMS
HANDLES
•
DELICATE,
•
PLASTIC
•
LEAD CRYSTAL
REPAIRED OR
ITEMS THAT
GLASS
PAINT /
ARE NOT HEAT
PATTERN
RESISTANT
OVERLAID
CHINA
Note :
Do not wash stainless steel and silver cutlery together. Iron objects can rust
and
stain other items. Aluminium tends to go black. Copper, pewter & brass
stain.
8
Page 10
BAUMATIC
COOK
WARE SO THAT THEY DO NO
T
WATER.
ALWAYS PLACE
GLASSES,
OR
THE HIGHER
LE
VEL
(POSITION ‘2’ IN
SUPREMA1W/SS dishwasher user manual
9
HOW TO USE THE UPPER RACK
THE UPPER
RACK IS FOR MORE DELICATE
AND
LIGHTER DISHWARE SUCH
AS
GLASSES,
COFFEE & TEA
CUPS, SAUCERS,
P
LATES, BOWLS, AND SHALLOW PANS
(PRO
VIDED TH
ESE ARE
NOT TOO DIRTY).
POSITION THE DISHES AND
GET MOVED BY THE SPRAY OF
CUPS & BO
WLS UPSIDE
DOWN.
NOTE
:
YOUR
DISHWASHER
COMES
WITH
AN
ADJU
STABLE
TOP RACK
(BASKET)
–
PICTURED
AT RIGHT. ITS
HEIGHT
CAN
BE
ADJUSTED BY UNDOING THE FR
ONT
RAIL
CLIPS,
REMOVING
THE
RACK
COMPLETELY
AND LATCHING THE
WHEELS OF THE LOWER LEVEL
(POSITION ‘1’ IN THE FIGURE ON THE RIGHT)
1
THE FIGURE ON THE RIGHT)
IN THE GR
OOV
E
OF
THE RA
IL.
2
9
Page 11
BAUMATIC SUPREMA1W/SS dishwasher user manual
10
***NOTE ***: THE UPPER
RACK HAS
SIDE
FLAPS
(PICTURED AT LEFT ABOVE BASKET).
TH
ERE ARE 4 (2 ON EACH
SIDE)
.
TH
ESE CAN BE ADJUSTED INTO 2
POSITIONS =
POSITION 1 (H
IGH)
AND POSITION 2 (LOW).
TO MOVE THE FLAPS BETWEEN THESE
PO
SITIONS, FIND THE
LARGE HINGES
CLASPING
EACH FLAP TO THE UPP
ER
RA
CK.
THERE ARE
TWO OF TH
ESE AT
EIT
HER END OF EACH FLAP. GENTLY P
ULL
B
OTH C
LASPS OFF
THE WIRE RACK AN
D
M
OVE
THE FLAP TO THE DESIRED
POSITION. BE
CAR
EFUL IF YOU HA
VE
LONG FINGERNAI
LS!
POSITION 1
THE UPPER POSITION WILL ACCOMMODATE ITEMS SUCH AS GLASS TUMBLERS
(PLACED
BENEATH FLAP) AND WINE GLASSES. WINE GLASSES CAN BE PLACED
UPSIDE
DOWN SO THAT THE NECK NESTLES SNUGLY IN THE GROOVES AT SIDE OF
FLAP
WITH THE BASE OF THE GLASS FACING UPWARD.
POSITION 2
WHEN THE FLAPS ARE MOVED TO THE LOWER POSITION, THEY CAN BE USED TO
HOLD
ADDITIONAL TUMBLERS, CUPS AND MUGS. ALWAYS CHECK THAT YOU ARE
ONLY
PLACING ITEMS ON THE FLAPS THAT WILL CLEAR THE CEILING HEIGHT OF
YOUR
DISHWASHER WHEN YOU PUSH THE RACK BACK IN. BE PARTICULARLY
CAREFUL
WITH LONG-STEMMED GLASSWARE SUCH AS CHAMPAGNE GLASSES –
BREAKAGE HAZARD!
10
Page 12
BAUMATIC SUPREMA1W/SS dishwasher user manual
11
NOTE
:
• WHEN YOU ARE SATISFIED YOU HAVE LOADED ALL THE UTENSILS
AND
DISHES YOU WANT TO WASH AND HAVE ADDED THE PROPER
AMOUNT
OF
DETERGENT TO THE DISPENSER
(REMEMBER TO CHECK THE
TABLE
ON
PAGE 13 FOR THE DOSE THAT’S RIGHT FOR THE WASHING CYCLE YOU
WANT),
ENSURE THE RACKS ARE PUSHED ALL THE WAY BACK INTO
YOUR
DISHWASHER AND CLOSE THE DOOR.
• YOU ARE NOW READY TO START A WASH CYCLE (SEE NEXT PAGE).
11
Page 13
BAUMATIC SUPREMA1W/SS dishwasher user manual
12
STARTING A WASH CYCLE
1
2
10
9
8
7
6 5 4 3
STARTING A WASH CYCLE
1)
MAKE SURE THAT THE PLUG OF THE APPLIANCE IS INSERTED INTO THE WALL SOCKET.
2)
MAKE SURE THAT THE WATER SUPPLY IS TURNED ON TO FULL PRESSURE.
3)
LOAD THE DISHWASHER (SEE THE SECTION ENTITLED ‘LOADING YOUR DISHWASHER’).
4)
POUR IN DETERGENT (SEE THE SECTION ENTITLED ‘SALT, DETERGENT & RINSE AID’).
5)
TURN THE KNOB LOCATED ON THE RIGHT OF THE CONTROL PANEL CLOCKWISE UNTIL THE NUMBER OR
THE
SYMBOL FOR THE CYCLE SETTING IS ALIGNED WITH THE REFERENCE MARK (SEE THE SECTION
ENTITLED
‘WASH CYCLE TABLE’ ON NEXT PAGE).
6)
PRESS THE ‘ON/OFF’ BUTTON. THE ON/OFF LIGHT WILL COME ON. THE WASH CYCLE WILL NOW BEGIN.
Note
:
The Delay Timer key (in above figure as mark number ‘6’) will set the start of the
washing
cycle by 30mins into the future for every press. You can set it up to 9½
hours
ahead of time for your convenience.
Approximate Timing of Wash Cycles
Intensive
12
(strong)
139
mins.
Normal
Economy
150
mins.
Rinse
95
mins.
Glass
76
mins.
Soap
103 7
mins. mins.
Page 14
BAUMATIC SUPREMA1W/SS dishwasher user manual
13
WASH CYCLE TABLE
OVERFLOW PROTECTION
YOUR BAUMATIC DISHWASHER HAS AN OVERFILL PROTECTION DEVICE WHICH AUTOMATICALLY SHUTS OFF
THE
INLET VALVE AND STARTS THE DRAIN PUMP IF THE WATER OVERFLOWS. IF
THIS OCCURS THEN TURN OFF
THE
MAINS WATER SUPPLY BEFORE CALLING THE SERVICE DEPARTMENT.
IF
THERE IS WATER IN THE BASE
PAN
BECAUSE OF AN OVERFILL OR SMALL LEAK,
THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE
DISHWASHER
13
Page 15
BAUMATIC SUPREMA1W/SS dishwasher user manual
14
WHAT YOU WILL SEE ON THE DISPLAY:
Digital sign: Shows the delayed time, remaining time and fault codes.
Delay sign: Shows this sign when delaying.
Washing sign: Displays this sign when washing.
Running sign: Display shows this when your machine is running a cycle.
Doesn’t
flicker when stopping.
Temperature sign: Shows the wash temperature at any time.
FORGET TO ADD A DISH?
A FORGOTTEN DISH CAN BE ADDED AT ANY TIME BEFORE THE DETERGENT
DISPENSER
OPENS.
•
OPEN THE DOOR A LITTLE TO STOP THE WASHING.
•
AFTER THE SPRAY ARMS STOP WORKING, YOU CAN OPEN THE DOOR
COMPLETELY.
•
ADD FORGOTTEN DISHES.
•
CLOSE
THE
DOOR,
THE
DISHWASHER
WILL
WORK
AFTER
TEN
SECONDS.
Need to Change the Cycle?
1.
PRESS THE PO
WER SWITCH TO
STOP WASHING
2.
PRESS THE ‘PROG.’ BUTTON TO SELECT
THE NEW PROGRAM
3.
PRESS THE PO
WER SWITCH
AGAIN TO START
WASHING
*
Note
– You
may have to
start a new cycle by reloading
the de
tergent
if it has been a long
time since
the old cycle began. See page 12 to
see
h
ow to do
this.
At the End of the Wash Cycle
At end of washing, the time display will flash for 8 seconds while the ALARM
sounds.
The ALARM will not sound at the end of delayed washing, howeve
r
We recommend you leave about ½ hour before unloading to
avoid injury and brittleness in dishware from heat.
14
Page 16
BAUMATIC SUPREMA1W/SS dishwasher user manual
15
FILTERING SYSTEM
FOR YOUR CONVENIENCE, WE HAVE PLACED THE FILTERING SYSTEM WITHIN EASY REACH INSIDE THE
TUB.
THE FILTER REMOVES BITS OF FOOD TRAPPED IN THE FILTER FROM THE WASH WATER SO IT CAN BE
RECIRCULATED DURING THE CYCLE. THERE ARE THREE PARTS TO THE FILTERING SYSTEM: 1) The Main Filter,
2) The Coarse Filter & 3) The Fine Filter.
1 MAIN FILTER
Food and soil particles trapped by this filter are
pulverized
by a
special jet on the lower spray arm and
washed
down the drain.
2 COARSE FILTER
Larger items, such as pieces of bone or glass that could
clog
the drain are trapped in the coarse filter. To
remove
an
item caught in this filter, gently squeeze
the
tabs on top of this filter and lift it out.
3 FINE FILTER
This filter holds soil and food residue in the sump area
and
prevents it from being re-deposited on the dishes
during
a
cycle.
Caring for your Dishwasher
CLEANING THE OUTSIDE SURFACES OF YOUR APPLIANCE
• TO CLEAN
THE EXTERIOR OF
YOUR DISHWASHER
(INCLUDING THE CONT
ROL PANEL), USE A LIGHTL
Y
DAMP
ENED CLOTH THEN DRY
THOROUGHLY.
NEVER
USE SH
ARP OBJECTS, SC
OUR
ING PADS OR
HARSH
CLEAN
ERS ON ANY PART OF THE APPLIANCE. SOME PAPER TOW
ELS CAN SCRATCH.
•
TO CLEAN THE EDGE AROUND THE DOOR,
ONLY
EVER USE A SOFT WARM, DAMP RAG.
DO
NOT USE A SPRAY CLEANER HERE OR
WHEN
CLEANING THE DOOR PANEL AS THIS
MAY
HARM THE DOOR LOCK AND
ELECTRICAL PARTS.
CLEANING THE SPRAY ARMS
THE SPRAY ARMS NEED REGULAR CLEANING AS HARD WATER RESIDUES WILL CLOG THEIR
JETS
&
BEARINGS. TO REMOVE THE SPRAY ARM, SCREW OFF THE NUT TO TAKE OUT THE
WASHER
ON
TOP OF THE SPRAY ARM AND REMOVE THE ARM. WASH THE ARMS IN SOAPY
WARM
WATER & USE A SOFT BRUSH TO CLEAN THE JETS. REPLACE THE SPRAY ARM AFTER
RINSING
IT
THOROUGHLY.
15
Page 17
BAUMATIC SUPREMA1W/SS dishwasher user manual
16
CLEANING THE FILTERS
• THE FIL
TER ASSEMBLY MUST BE KEPT CLEAN FOR
BEST PERFORMANCE. You should
remove the
l
arger bits of
food trapped in the filter after each w
ash cycle by
rinsing
the semicircular f
ilter and
cup
under running water. To re
move the f
ilter assembly, pull up on the cup handle.
•
The entire filter assembly should be cleaned at least once a month.
• To clear the coarse filter and the
fine filter, use a cleaning b
rush. T
hen, reassemble the filter parts
as shown in the
figure above and reinsert the entire assembly in
the di
shwasher in its seat & press
downward
to secure it.
• Improper replacement of
the filter may impair appli
ance performance and d
amage di
shes and
utensils.
•
Warning - never run the dishwasher without the filters
in place!
•
Warning - Before cleaning the inner cavity of the appliance
always allow 30 minutes for the Element to cool down to
avoid injury!
16
Page 18
BAUMATIC SUPREMA1W/SS dishwasher user manual
17
HOW TO KEEP YOUR DISHWASHER IN SHAPE
A
FTER
EVERY
WASH
, leave the door slightly ajar so that moisture and odours are not trapped
inside.
R
EMOVE THE
PLUG
before cleaning or performing maintenance. Never run the risk of electric
shocks.
D
O
NOT
USE
SOLVENTS OR
ABRASIVE
CLEANING
AGENTS
to clean the exterior and the rubber
parts of the dishwasher. Only use a cloth and warm soapy water. To remove spots or stains
from
the surface of the interior, use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
W
HEN YOU
GO ON
HOLIDAY
, run a wash cycle with the dishwasher empty. Then unplug it, turn off
the water supply and leave the door slightly ajar to prevent odours and mould from developing.
M
OVING THE
APPLIANCE
is possible but KEEP IT UPRIGHT.
S
EALS
can trap food, which in turn will cause odours. Periodic cleaning with a damp cloth or
sponge
will prevent this from becoming a problem.
PROTECTING OUR ISHWASHER AGAINST REEZINGY D F
If your dishwasher is left in an unheated place during the winter, ask a
service
technician to:
1)
Cut off
electrical power to the dishwasher. Rem
ove fuses or trip circu
it
break
er.
2)
Turn off the
water supply
and disconnect the w
ater inlet pipe from the
water
valv
e & di
scharge hoses.
3)
Drain water from the inlet pipe and
water
valve
(Use a pan to
catch the
wat
er).
4)
Reconnect the
water inlet
pipe to the
water
valve.
5)
Remove the plastic sump cover in the tub bottom and use a sp
onge to soak
up water in the rubber b
oot.
17
Page 19
BAUMATIC SUPREMA1W/SS dishwasher user manual
18
BEFORE YOU CALL FOR SERVICE …
CHECKING AGAINST THE CHARTS BELOW MAY FIX YOUR PROBLEM.
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
• Replace fuse or reset circuit
breaker.
• Fuse blown, or the
circuit
breaker acted
• Remove any other appliances
feeding
from the same socket as
the dishwasher.
Dishwasher
doesn’t run!
• Power supply is not
turned on
on and the door is closed securely.
• Make sure the dishwasher is turned
• Check that the water supply is
connected properly and the water is
turned on.
• Water pressure is low
• The system is designed to detect an
overflow. When it does, it shuts off
Drain Pump
doesn’t stop!
• Overflow
the circulation pump and turns on
the drain pump. Call a Baumatic
Ltd approved technician.
action and detergent cup opening.
• Sound from soft food shredding
• Some audible sounds
are
normal
This is not a problem.
• Utensils are not secure
in the baskets or
something small has
dropped into the
securely in the dishwasher.
• Ensure everything is placed
Noise!
basket and is loose
• Dishwasher has not been used
regularly. If you do not use it
often, remember to set it to fill and
• Motor Hums
pump out every week. (See Wash
Cycle table). This will help keep the
seal moist.
18
Page 20
BAUMATIC SUPREMA1W/SS dishwasher user manual
19
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
detergent to avoid suds.
• Use only special dishwasher
Suds in the Tub!
• Improper detergent
immediately.
• Always wipe up rinse agent spills
• Spilled rinse agent
Stained tub
Interior!
• Detergent with
colorant was used
• Make sure you use detergent
without colorant.
Dishes are not
dried!
• Rinse agent dispenser
is empty
• Make sure that the rinse agent
dispenser is filled.
Dishes and
Flatware not
Clean!
• Improper program
• Select stronger program.
• Make sure there are no large dishes
blocking the action of the detergent
dispenser
and the spray arms.
• Improper rack loading
To remove spots from glassware:
Spots and Filming
on Glasses and
Flatware!
1. Take all metal utensils out of the
• Extremely hard water
dishwasher.
• Low inlet temperature
2. Do not add detergent.
• Overloading the
dishwasher
3. Choose the longest cycle.
4. Start the dishwasher and let it to run for
• Improper loading
18 - 22 minutes, then it will be in the main
• Old or damp powder
detergent
wash.
5. Open the door and pour 2 cups of white
• Empty rinse agent
vinegar into the bottom of the dishwasher.
dispenser
6. Close the door and let the dishwasher
• Incorrect dosage of
detergent
complete the cycle.
7. If the vinegar does not work, repeat as
above, only use ¼ cup (60ml) of citric acid
crystals
instead of vinegar.
19
Page 21
BAUMATIC SUPREMA1W/SS dishwasher user manual
20
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
Cloudiness on
glass!
• Combination of soft
water and too much
detergent
water and select a shorter cycle to
• Use less detergent if you have soft
clean the glassware.
Yellow or brown
film on inside
surfaces!
• Use a solution of ½ cup of bleach
and 3 cups warm water to remove
• Tea or coffee stains
the stains by hand. Rinse
thoroughly.
• Iron deposits in water
can cause an overall
film
company for a special filter.
• You have to call a water softener
White film on
inside surface!
• To clean the interior, use a damp
sponge with dishwasher detergent
and wear rubber gloves. Never use
• Hard water minerals
any other cleaner than dishwasher
detergent for the risk of foaming or
suds.
Detergent cup lid
won’t latch!
• Button is not in the
• Turn the Button to ‘OFF’ position
and
slide the door latch to the left.
‘OFF’ position
Detergent left in
dispenser cups!
• Dishes block detergent
cups
• Reload the dishes properly.
through the vent by the door latch
• There is some steam coming
Steam!
• Normal phenomenon
during drying and water draining.
20
Page 22
BAUMATIC SUPREMA1W/SS dishwasher user manual
21
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
Black or grey
marks on dishes!
• Aluminium utensils
have rubbed against
dishes
• Use a mild abrasive cleaner to
eliminate those marks by hand.
Water standing in
the bottom of the
tub!
around the outlet on the tub bottom
• A small amount of clean water
• This is normal
at the back of the tub keeps the
water seal lubricated. No action
needed.
• Be careful not to overfill the rinse
aid dispenser.
oversudsing and lead to
• Spilled rinse aid could cause
• Overfilled dispenser or
rinse aid has spilled
overflowing.
cloth.
• Wipe away any spills with a damp
Dishwasher leaks!
• Dishwasher isn’t level
• Make sure the dishwasher is level.
• Make sure if you’re using 3-in-1
tablets that you do not put rinse aid
and salt into the appliance as well.
• 3-in-1 Tablets
attaching appliance to work surface
• Level appliance & ensure top screws
Door popping
open!
• Appliance not level
are not lifting the weight of the
dishwasher.
WARNING!
IF OVERFLOW OCCURS, TURN OFF THE MAIN WATER SUPPLY BEFORE CALLING A SERVICE
TECHNICIAN.
IF
THERE IS WATER IN THE BASE OF THE TANK PAN BECAUSE OF AN OVERFILL
OR SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE DISHWASHER.
21
Page 23
BAUMATIC
‘Err4’ MESSAGE.
REFER TO
SUPREMA1W/SS dishwasher user manual
22
ERROR CODES -
WHAT THEY MEAN
* YOUR DISHWASHER MAY EXPERIENCE A FAULT. SHOULD THIS HAPPEN, A
CODE
CONSISTING OF ‘E’
& A
NUMBER FROM 1-7 CAN BE DISPLAYED.
USE
O
NDERSTAND WHAT IS RONGTHIS TABLE T U W .
*NOTE* : ALWAYS CALL FOR A Baumatic Ltd ENDORSED / APPROVED
SERVICE TECHNICIAN TO CARRY OUT REPAIRS.
CODE
SYMPTOM:
CAUSE:
WHAT TO DO:
Ensure that inlet hose is not
‘Err1’
LONGER FILL TIME.
FAUCET IS NOT OPENED.
kinked or crushed.
THE DRAIN PIPE WAS PLACED
TOO HIGH WHEN IT WAS
INSTALLED.
Ensure drainage system is as
‘Err2’
per
manual and not
LONGER or EXTENDED DRAINING TIME
extended.
MALFUNCTION OF
TEMPERATURE SENSOR OR OF
HEATING ELEMENT.
LONGER HEATING TIME – NOT
REACHING REQUIRED TEMPERATURE
CALL FOR A QUALIFIED
‘Err3’
S ERVICE TECHNICIAN.
TOO MUCH INLET WATER.
Overdosing. 3-in-1 put in
with salt and/or rinse aid in
*NOTE * - THERE ARE
NUMEROUS CAUSES OF AN
the appliance =overdose.
‘Err4’
OVERFILLED
APPLIANCE USAGE SECTION
OF
THIS MANUAL FOR
GUIDELINES
ON
HOW TO
PREVENT AN OVERFILL.
Could also be a Water
P ressure problem.
CALL FOR A QUALIFIED
‘Err6’
OPEN CIRCUIT
THERMISTOR.
S ERVICE TECHNICIAN.
CALL FOR A QUALIFIED
‘Err7’
SHORT CIRCUIT
THERMISTOR.
SERVICE TECHNICIAN.
WARNING!
IF OVERFLOW OCCURS, TURN OFF THE MAIN WATER SUPPLY BEFORE CALLING A SERVICE
TECHNICIAN.
IF
THERE IS WATER IN THE BASE OF THE TANK PAN BECAUSE OF AN OVERFILL
OR
SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE DISHWASHER.
22
Page 24
BAUMATIC SUPREMA1W/SS dishwasher user manual
23
DISHWASHER CHARACTERISTICS
The BAUMATIC SUPREMA1W/SS dishwasher model is based firmly on convenience.
Apart
from having the same general workings as other household dishwashers, it has
several
extra features.
14 place settings -
Normal wash load of 14 place settings.
Dishwasher -
Your dishwasher has a A rated wash
performance,
A
rated drying performance and A rated energy
efficiency.
Rinse aid Warning
Indicator -
If the rinse aid is running low,
this
signal will light up on the control panel, alerting
Overflow protection -
Your
dishwasher has an overfill protection program which could
you to top the rinse aid level up so the machine can
keep
at
its optimum performance level.
automatically shut off the inlet valve and start the drain pump if the
w ater Overflows.
Automatic Power off
Stainless steel tub-
function
Y ou need not worry about stains to the tub.
Automatically shuts the power off after washing.
6 wash programs -
You can choose
desired
program according to the soiled level. Such as, intensive
wash,
normal wash, economy, rinse, glass, rapid and pre-wash,
etc.
Then you can change the temperature of the wash.
Adjustable upper basket
-
Even if the dishware is large, you can load the dishes by
adjusting
the basket.
Error alarm–
Fault codes
show on the display if there is a fault with your
dishwasher.
Salt Warning Indicator -
If the salt is running low, this signal will light up on the control
panel
to
alert you to top the salt level up so the machine can
keep
at
its optimum performance level.
Temperature display -
Displays the wash temperature at any moment. If you know the
water temperature, you’ll be less likely to be scalded when you
open
the door.
Broad applied
voltage -
This appliance uses AC
Remaining time
(alternating current) voltage. Please be aware that this
will
make its operation vulnerable to uneven current in
your
home and power surges.
indicator
The length of time left in the program will be clearly
displayed
in
the text window, leaving you in no doubt
as to when the program will end.
4 Different wash
temperatures
Time delay feature –
This
The intensive, normal, economic, rinse, glass
and rapid wash have different temperature
options which you can set before you start a
washing cycle.
allows the start of the program to be delayed between 1 and 9½
hours for your convenience and for saving on energy!
23
Page 25
BAUMATIC SUPREMA1W/SS dishwasher user manual
24
INSTALLATION INSTRUCTIONS
NOTE: APPLIANCE SHOULD ONLY BE FITTED
BY A TRAINED TECHNICIAN
INSTALLING YOUR DISHWASHER
Your
sher s with a freestanding feature, youdishwa i
only
to o
ollowing:need d f
80;/
1 Levelling the Appliance(pls see the section “get your dishwasher
level
in
page 25)
2 Connect the water inlet (pls see page 26)
3 Electrical connection (see page 27)
Also
i
nstall it to a cabinet cavity accordingyou can
follow
i
ng:
a) PREPARATION
Before you install your appliance, make sure that the place you
have
chosen to fit it is:
o
Near the existing
power
socket
(marked 4 in figure).
o
So that you can
choose
one side of the
cabinet cavity to
easily
connect the
dishwasher’s
drain
hoses.
o
Near your sink so
you
have easy
access to the water
inlet
and drain hoses
(marked 3
[inlet] & 2 [drain] in
figure).
24
Page 26
BAUMATIC
OF YOUR DISHWASHER!
SUPREMA1W/SS dishwasher user manual
25
INSTALLING
REMEMBER THE DIMENSIONS
YOUR
THESE ARE (measured in
DISHWASHER
figure in mm):
INTO A
ETCABIN
AREA
o If
dishwasher is to be
installed
at
the corner
of cabinet area, make
sure you have enough
space when the door is
opened.
o
Is structured so that
you have
less
than
5
mm between the
top of the dish w a sh er
and cabinet. Also
check
that the
outer
door is aligned
to cabinet.
FIRSTLY, GET YOUR DISHWASHER LEVEL
-
Use spirit levels to
level
your
dishwasher
Note:
Once the appliance is positioned, adjust the
Four
feet (screwing them in or out)
to adjust the height of the dishwasher, making
it level. In any case, the appliance should
not be inclined more than 2°.
25
Page 27
b) Connecting
to
he mains water supplyt
IMPORTANT: Do not connect the appliance to your mains water supply
using an old or an ex ist ing w at er in let h ose. The inlet ho se su pplied wit h
the dishwasher is the ONLY one that should be used.
o The inlet hose will be located inside the cabinet of the dishw asher.
o Connect the water inlet hose to a threaded water tap that has a 3/4” thread.
o Fully tighten the inlet hose to the water tap.
c)
DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP.
IMPORTANT: If the inlet hose is fitted with an aqua stop. This
MUST be fitted in the upright position, as shown in the above
diagram.
ing he rain hoseConnect t d
9
Secure the drain hose, so that it cannot move whilst the dishwasher is in use.
9
Place the end of the drain hose on your drain pipe. Push it a short way down
into your drain pipe.
9
IMPORTANT: Do not insert the drain hose too deeply into the water pipe, as
this may cause siphoning.
9
NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH.
26
Page 28
BAUMATIC SUPREMA1W/SS dishwasher user manual
27
d) NOW YOU ARE READY TO CONNECT THE
POWER CORD.
WARNING!
ELECTRICITY CAN BE DANGEROUS. PLEASE READ THE FOLLOWING
CAREFULLY :
ELECTRICAL CONNECTION
Electrical Requirements
The di
shwasher is designed for operation on an adequately wired
individual 220-240V AC,
50Hz system. The requi
red fuse rating is 13amp.
Fused elect
rical supply is req
uired –
copper wire
only. Time
delay fuse or circuit breaker is
recommended. Make
sure that this
applia
nce runs off its own separate circ
uit. Outlet
should be placed in
adjacent cabinet.
WARNING
ENSURE PROPER GROUND EXISTS–
BEFORE
SEU .
After making sure that the
voltage and the
frequency values for the
current in your home
corres
pond to those on the rating plate and
that
the electrical
system is
sized for the
maximum voltage on the rating pl
ate, i
nsert the plug into an electrical
socket which is earthed
properly. If the electrical socket to which the ap
pli
ance must be connected is not right for
the
plug, replace the
socket, rather than using ad
aptors of the like as they
could cause
overheating and fire.
27
Page 29
BAUMATIC SUPREMA1W/SS dishwasher user manual
28
e) THEN, APPLY THE CONDENSATION STRIP.
The Condensation Strip must be fitted to the
underside of the worktop above your dishwasher
to protect it against any moisture. Its purpose
is to deflect steam rising from your appliance to
protect your worktop’s underside.
• The strip is located inside your
dishwasher.
• Ensure the surface is clean prior to
sticking to underside of the worktop.
• Separate the backing paper from the
strip.
• Stick to the underside of the worktop.
Note: Failure to attach strip could
result in damage to the underside
of your work surface!
f) NOW YOU ARE READY TO PUSH THE
DISHWASHER INTO POSITION
(SEE FIGURE BELOW):
NOTE
–
MAKE SURE YOU HAVE THE
DISHWASHER
ON
ITS SLIDE
RAILS
(SEE I
LLUSTRATION ON
RIGHT).
* Note *
You can detach the top board
(5)
that comes as part of your
dishwasher
if you want to
i
nstall your dishwasher in
your
cabinet.
THEN MOVE IT INTO THE
CABINET RECESS (AS
PICTURED ON RIGHT, 6-7
),
ENSURING
THAT IT IS BACKED
UP AGAINST THE WALL.
g) ENSURE THAT DISHWASHER IS LEVELYOUR
IN ITS NEW POSITION
.
28
Page 30
BAUMATIC SUPREMA1W/SS dishwasher user manual
29
NOTE:
YOUR DISHWASHER MUST BE
LEVEL
FOR PROPER DISH RACK
OPERATION
AND WASH
PERFORMANCE.
(GO BACK AND LOOK
AT THE BOTTOM RIGHT DIAGRAM ON PAGE
24).
IT’S IMPORTANT TO MAKE SURE
THAT
YOUR DISHWASHER IS
LEVEL
AGAIN, BECAUSE THE
FLOOR
SURFACE MAY BE
DIFFERENT
TO
WHERE YOU HAD
ADJUSTED IT BEFORE YOU MOVED
THE
DISHWASHER INTO PLACE
WARNING!
BE CAREFUL WHILE YOU ARE LEVELLING YOUR DISHWASHER IN PLACE
– IT COULD TIP OVER AND INJURE YOU!
FINAL CHECKLIST BEFORE OPERATING
NOTE: BEFORE
YOU START USING YOUR DISHWASHER,
PLEASE
MAKE SURE YOU HAVE CHECKED
:
•
WHETHER THE DISHWASHER IS LEVEL AND
FIXED.
•
WHETHER THE INLET VALVE IS OPENED.
•
WHETHER THERE IS LEAKAGE AT THE
CONNECTIONS
OF
THE CONDUCTS.
•
WHETHER THE WIRES ARE TIGHTLY
CONNECTED.
•
WHETHER THE POWER IS SWITCHED ON.
•
WHETHER THE INLET AND DRAIN HOSES
ARE
KNOTTED / KINKED.
•
WHETHER ALL PACKING MATERIALS &
PRINTED
MATTER HAVE BEEN REMOVED
FROM
THE DISHWASHER.
PLEASE
HIS MANUAL FOR FUTUREKEEP T
29
REFERENCE
Page 31
Minimum and maximum plate sizes
Maximum height of
dishes (upper basket)
With upper
19 cm 30 cm
Maximum height of
dishes (lower basket)
basket raised
With upper
24 cm 25 cm
basket lowered
IMPORTANT: Care should be taken to make sure that the spray
arms can move freely when items have been loaded into the
baskets.
Page 32
Environmental note
ging
ging
o The packa
friendly and can be recycled.
o Please discard all packa
environment.
materials that Baumatic uses are environmentally
material with due regard for the
Page 33
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Service Telephone
(0118) 933 6911
Service Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Technical Advice Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Republic of Ireland
01- 6266 798
Czech Republic
Baumatic CR spol s.r.o.
Amperova 495
46215, Librec
Czech Republic
+420 800 185 263
www.baumatic.cz
Slovak Republic
Baumatic Slovakia, s.r.o.
Skultetyho 1
831 04 Bratislava 3
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Janderstrasse 9
Mannheim, 68199
Germany
+4962 112 9190
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Caltana 129
Campodarsego (Padova), 35011
Italy
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
The Netherlands
+3136 549 1555
www.baumatic.nl
Page 34
Page 35
Page 36
22
Loading...