Page 1
P10SS/P14SS/P15SS/
P20SS Cooker Hood
Page 2
User Manual for your Baumatic
P14SS Pythagora 60 cm cooker hood
P10SS/P15SS/P20SS Pythagora
90 cm cooker hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 20/06/07
2
Page 3
Contents Page
Environmental note 4
IMPORTANT SAFETY INFORMATION 5 – 7
Specifications of your cooker hood 8
Using your Baumatic cooker hood 9
The control panel 9
Controlling your cooker hood 10
The timer button 10
Grease filter maintenance alarm 10
Cleaning your Baumatic cooker hood 11
The grease filter 11
Maintenance 12
Removing and cleaning the grease filter 12
Changing a light bulb (P10SS only) 13
Changing a light bulb (P14SS, P15SS and P20SS) 14
Fitting the carbon filter 15
Installation 16
Electrical connection 17
Before beginning installation 18
Extraction mode or recirculation mode? 19
Installing your cooker hood 20 - 23
Connecting to external ducting 24
Fitting the chimney section 25 - 26
Troubleshooting 27
Baumatic Ltd. conditions of guarantee 28
Contact details 29
3
Page 4
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
Page 5
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of information contained in this
booklet, please contact the Baumatic Technical
Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product in any way. Do not tamper with it or attempt to modify
the appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
¾ Electric cookers: 700 mm
¾ Gas cookers: 700 mm
¾ Coal/ oil cookers: 800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
5
Page 6
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in extraction mode, then ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
o Ensure that the ducting used in extraction mode has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
6
Page 7
o The manufacturer refuses to accept any responsibility for
damages arising to the cooker hood or your property from a
failure to observe the fire safety advice contained in this
instruction booklet.
o Remember that when in extraction mode, your cooker hood is
removing air from the room it is installed in. Ensure that proper
ventilation measures are being observed. Note that it
removes odours from the room, not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including cleaning and
replacing light bulbs.
o Do not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
o Do not install the appliance above a cooker with a high level grill.
o Never leave frying pans unattended during use
as overheated fats and oils might catch fire.
o Never flambé cook under this cooker hood.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
o The lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7
Page 8
Specifications of your cooker hood
Congratulations on purchasing a Baumatic Cooker
Hood!
PRODUCT DIMENSIONS
P10SS P14SS P15SS P20SS
Height (mm) 572 -
1072
560 1060
560 1060
584 -
1070
Width (mm) 898 598 898 900
Depth (mm) 490 480 480 509
Chimney
dimensions (mm)
260 x
263
258 x
261
258 x
261
276 x
268
Your cooker hood is fitted with:
o High extraction tangential motor
o Touch control operation
o 4 Speeds
o 2 Stainless steel grease filters (P14SS only)
o 3 Stainless steel grease filters (P10SS, P15SS and
P20SS)
o 2 halogen lights (P10SS only)
o Fluorescent light
Extraction capacity: 800 m³/hr
Optional Extra: 1 x SCS14 carbon filter for air
recirculation mode
8
Page 9
Using your Baumatic cooker hood
The control panel
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o Find the control panel, which is located at the front of the cooker
hood.
o There are several buttons on the control panel, which perform
separate functions.
(Timer button)
(Increase speed)
(On/off button)
(Decrease speed)
(Light ON/OFF button)
(LCD display)
IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR
HOOD TEN MINUTES BEFORE YOU START TO COOK,
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
YOU SHOULD ALSO RUN YOUR HOOD FOR TEN
MINUTES AFTER YOU HAVE FINISHED COOKING.
9
Page 10
Controlling your cooker hood
o Use the ON/OFF button to switch the cooker hood on.
o Use the plus and minus buttons to regulate the speed that the
motor is running at.
o The speed level that you have selected will appear on the LCD
display.
o To switch the cooker hood off, press the ON/OFF button again.
The timer button
o If you press the timer button whilst the cooker hood is in
operation, then it will countdown for 15 minutes.
o During the countdown the light around the timer button will
flash.
o When the countdown has finished the cooker hood will switch
off.
o If you press the timer button again during the countdown, the
light around the timer button will go out and the cooker hood will
return to normal operation.
Grease filter maintenance reminder
o After approximately 30 hours of operation, the timer button will
glow red. This means that the grease filters need to be cleaned.
o You should follow the grease filter cleaning operation that is
outlined on pages 11-12 of this instruction booklet.
o When the grease filters have been put back in position, turn on
the hood and then hold down the timer button until the red light
goes out.
o Turn the hood off and then back on again, to check that the
alarm has been reset.
o IMPORTANT: The grease filter should be cleaned at the time
intervals suggested on page 11. You should not wait until the
maintenance alarm activates before cleaning the grease filter.
IMPORTANT: TO MAINTAIN THE CORRECT
FUNCTIONING OF THE CONTROL PANEL, WE
RECOMMEND THAT YOU REGULARLY CLEAN THIS
AREA.
10
Page 11
Cleaning your Baumatic cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS
ENSURE THAT YOU HAVE SWITCHED YOUR
COOKER HOOD
SWITCH, SET AT THE WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filter at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filters.
OFF AT THE OMNI-POLAR
The grease filters
o Your cooker hood includes grease filters which help to absorb
grease particles, to protect your kitchen & furniture from greasy
residues.
o This metallic filters may become flammable if they become
saturated with this greasy residue.
o To prevent a fire hazard, the filters should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at
least once a month, using hot water and normal washing-up
detergent.
o DO NOT WASH THE GREASE FILTERS IN A DISHWASHER.
11
Page 12
Maintenance
Removing and cleaning the grease filters
o Remove a grease filter by lifting up the catch
and then pulling the filter away from the
hood.
o Soak the grease filters in hot water and washing up liquid for
about an hour.
o Rinse them off thoroughly with hot water.
o Repeat the process if required.
o Refit the grease filters once they have dried.
o IMPORTANT: Let the grease filters dry thoroughly before
refitting them in the cooker hood.
12
Page 13
Changing a light bulb (P10SS only)
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
o Prior to touching the light bulbs ensure
they are cooled down.
o Find the bulb that requires replacement,
you will find it located in the light f
which is on the underneath of the
cooker hood.
o Using a flat tipped screwdriver, remove the bulb and
insert a new GU4 12V 20W (max) bulb.
o IMPORTANT: Defective bulbs should be replaced
immediately.
o If the light or lights still do not work, make sure that the lamps
are fitted properly into their housings before you call for
technical assistance.
ixture
13
Page 14
Changing a fluorescent bulb (P14SS, P15SS and P20SS)
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A FLUORESCENT TUBE, YOU MUST ENSURE THAT
YOU HAVE DISCONNECTED THE COOKER HOOD
FROM YOUR MAINS SUPPLY.
o Prior to touching the fluorescent tube ensure that it has cooled
down.
o Unscrew the fixing screws and remove the panel that covers the
fluorescent tube.
o Remove the fluorescent tube by rotating it through 90°.
o Replace the fluorescent tube with one of the same rating as the
tube originally supplied with the cooker hood.
o IMPORTANT: A defective fluorescent tube should be replaced
immediately.
o If the light still does not work, make sure that the fluorescent
tube is fitted properly into its housing before you call for
technical assistance.
o Replace the bottom panel and fully tighten the fixing screws.
14
Page 15
Fitting the carbon filter
If the appliance is going to be used in recirculation mode then it is
necessary to fit a carbon filter. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTER, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
o Remove the grease filters.
1) Locate the
SCS14 carbon
filter into the
slots on the
cooker hood,
below the
motor.
2) Push the other side of the filter upwards until it clicks into place.
3) Securely tighten the screw through the hole in the SCS14 carbon
filter and the corresponding hole in on the underneath of the cooker
hood.
o Refit the grease filters.
o The carbon filter should be replaced every three months or if it
shows signs of damage.
15
Page 16
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filters.
The manufacturer declines all responsibility in the event of the
installer failing to observe all the accident prevention
regulations in force, which are necessary for normal use and
the regular operation of the electric system.
16
Page 17
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The power cable must be connected to the terminals marked L
(live) and N (neutral) in the hood and fixed with a cable clamp.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet.
(UK ONLY).
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
o As the colour of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
o The blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
o The brown wire must be connected to the
terminal marked “L” (live), or coloured red.
17
Page 18
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Before commencing installation of the cooker hood the grease
filters should be removed.
o Check the inside of the product and ensure that there is no
transit packaging or any other materials, such as packets of
screws, guarantees etc. These should be removed and kept for
future use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
should be placed over the worktop, hob top or cooker. This will
help to protect these surfaces from damage and debris.
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood
parts and fittings on it.
o Rawl plugs are provided to secure the hood to most types of
walls and ceilings. However a qualified technician must verify the
suitability of the materials, in accordance with the type of wall
and ceiling. The wall and ceiling must be strong enough to take
the weight of the hood.
o Do not tile, grout or silicone this appliance to the wall. This
appliance is designed to be surface mounted only.
o Remove any protective wrapping that has been put on the
cooker hood or chimney sections, to protect them during transit.
18
Page 19
Extraction mode or recirculation mode?
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE.
What is the difference between extraction and recirculation
modes?
In extraction mode, the stale air will be taken out of the room via
external ducting.
In recirculation mode stale air is taken via the grease filter, and passed
through a charcoal filter for purification. The air then re-enters the
kitchen via an opening in the hood.
For optimum performance, we recommend that the cooker hood is
used in extraction mode and connected to external ducting.
Unfortunately if you live in a flat or the hood is too far from an outside
wall, this may not be possible. The only alternative is to recirculate the
air.
Do I need a charcoal filter?
All cooker hoods have grease filters but if you are using your cooker
hood in recirculation mode, then a charcoal filter must be fitted in
addition to the grease filters.
19
Page 20
Installing your cooker hood
o We recommend that at least two people install this hood.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO
YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION
PROCESS HAS BEEN COMPLETED.
1) Remove the metal grease filters.
2) The mounting bar that you hang the hood on can be found on the
side of the housing motor or in the package that contains the fixing
screws and instruction manual.
3) Measure a distance of 700
mm from the hob top that will
be underneath the cooker hood.
Then measure out a further 310
mm above the height of
measurement Y (Y being the
thickness of the canopy section
of the cooker hood).
20
Page 21
4) Using a pencil, mark the
centre of the wall where the
cooker hood will be installed.
Place the mounting bar against
the wall and ensure that the
middle of it is placed on the
centre mark.
o Use a pencil to mark the
position of where the
screw holes will be drilled.
o Use a spirit level to ensure
that the two markings are
horizontally level.
5) Using a drill bit with an 8 mm
diameter, make holes in the wall on the
positions that you marked in step 4.
6) Insert rawl plugs into the two holes that you have
just drilled.
o Screw the mounting bar to the wall using 2 x 8
mm screws.
o IMPORTANT: You must make sure that the
mounting bar is the right way up and the
right way around. Please see picture 4 if you
are unclear of the correct position for the
mounting bar.
o Fully tighten these screws to fix the mounting bar to the wall.
21
Page 22
7) Hook the hood onto the
mounting bar.
8) If required you can adjust the alignment of the cooker hood using
the screws on the brackets that hook over the mounting bar.
o The top screw (B) adjusts the distance from the wall and the
bottom screw (C) adjusts the height.
22
Page 23
9) Mark the position of the lower screw holes that need to be drilled
out in step 10. The holes can be found immediately below the motor
housing. (The position of one of the holes is indicated in the above
photograph by the screwdriver).
10) Remove the hood from the
mounting bar and then using a drill bit
with an 8 mm diameter, make holes in
the wall on the positions that you
marked in step 9.
11) Insert rawl plugs into the holes that you have just
drilled.
o Follow steps 7 and 8 again (i.e. rehang the hood
on the mounting bar and then adjust its angle and
height, so that the drilled holes line up with the
lower holes inside the hood again).
o From the inside of the hood, tighten screws into
the holes that you drilled in step 10.
o IMPORTANT: You must fully tighten these screws, as they
assist in fixing the hood to the wall.
23
Page 24
Connecting to external ducting
12) Connect the coupling (D) to the top of the cooker hood.
o You may find an anti-draft flap included with the fixtures and
fittings for the cooker hood. You should sit this in the top of the
coupling.
o Connect a 125 mm ducting hose (E) to the coupling. Please note
that the ducting hose is not supplied with the appliance.*
o The other end of the ducting hose should be connected to a
discharge outlet that is suitable for cooking vapours. It should
have a cross section of at least 150 cm².
o The maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend.
* It is possible to purchase a ducting kit from the Baumatic Spares
Department (either the DK5 or DK10).
24
Page 25
Fitting the chimney
13) Separate the two
chimney sections (G and H).
o Rest the bottom of
chimney section G on the
top of the hood. Making
sure that the holes at the
bottom of it, line up with
the securing holes on top
of the motor housing.
o If you want to install the
appliance at its minimum
height (i.e. only using one
section of chimney), then
you should complete
steps 14-18 using
chimney section G only.
14) Lift chimney section H upwards to the desired height. You must
ensure that it is perpendicular to the hood.
o Mark the side measurement of both sides of chimney section H
on the wall with a pencil and then remove chimney sections G
and H.
15) Take the fixing bracket (L) and place it between the two pencil
marks that you made in step 14. Use a spirit level to ensure that the
bracket is level before marking the position of the screw holes.
o Keeping the bracket in contact with the wall, use a pencil to
mark the position of the holes at either end of the bracket on the
wall.
25
Page 26
16) Using a 4 mm drill bit, drill out holes on the pencil markings that
you made in step 15. Insert rawl plugs into the holes and then use a
screwdriver to secure the fixing bracket to the wall.
17) Place chimney section G back onto the hood.
o Make sure that the holes in the bottom of chimney section G line
up with the securing holes on top of the main body of the motor
housing.
o From inside of the motor housing, screw chimney section G to
the hood. You should make sure that you fully tighten these
screws.
o Slide chimney section H back inside of chimney section G (unless
you are installing the cooker hood at its minimum height and
only using the lower chimney section).
26
Page 27
o IMPORTANT: Make sure that the vent on either side of chimney
section H is pointing upwards and not inside of chimney section
G.
18) Lift chimney section H up to the fixing bracket that you secured to
the wall in step 16. Secure it to the fixing bracket using the screws
provided. Make sure that these screws are fully tightened.
o If you are installing the appliance at its minimum height, then
you should connect chimney section G to the fixing bracket.
Electrical connection
The electrical connection must correspond to the electrical requirement
noted on the rating plate, which is placed inside of the cooker hood.
The appliance should be connected to the electrical supply. See pages
16 – 17 for detailed information on the electrical connection.
Refit the grease filters and then switch on the mains
supply to the appliance. Press the ON/OFF button and
check that the appliance is operating correctly.
27
Page 28
Troubleshooting
IMPORTANT: If your cooker hood appears not to be operating
properly, before contacting the Baumatic Service Department,
please refer to the checklist below.
My cooker hood will not start.
o Check that the hood is connected to the power supply and
whether you have selected any of the fan speeds.
My cooker hood is not working effectively.
o Check that fan speed is set to an appropriate setting.
o Check that the grease filter is not dirty and if it requires
cleaning.
o If the hood is set up for recirculation mode, check that the
carbon filters do not need to be replaced.
o If the hood is set up for extraction mode, check that the ducting
hose and discharge outlet are not blocked.
o
My cooker hood is noisy and/or vibrating.
o Check whether the installation has been completed as per the
instruction booklet.
o It is normal to get a certain amount of noise and vibration, due
to the extraction capacity of the cooker hood.
DO NOT MAKE ANY ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF. IF THE APPLIANCE IS STILL NOT OPERATING
CORRECTLY, PLEASE CONTACT THE BAUMATIC SERVICE
DEPARTMENT ON TELEPHONE NUMBER (0118) 933 6911.
28
Page 29
Baumatic Ltd. Conditions of guarantee
Dear Customer,
Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and
labour costs resulting from defective materials or workmanship.
Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12
months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period
applies to England, Scotland, Wales and Northern Ireland only.
To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase
to be covered under this guarantee. This can be done online via: www.baumatic.co.uk or through returning
the guarantee card which can be found in each new Baumatic appliance.
* In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of
charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any
defect that arises due to faulty materials or workmanship within a period of 5 years from the original
purchase date.
* An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the
warranty period.
Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the
policy is negated and Baumatic Ltd will be under no further liability.
The guarantee covers the appliance for normal domestic use only, unless otherwise stated.
Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale
issued at the time of purchase.
This guarantee is transferable only with the written consent of Baumatic Ltd.
If the appliance fails and is considered either not repairable or uneconomical to repair between 12 months
(2 years if registered) and five years, a free of charge replacement will not be offered.
The guarantee for any replacement will only be for the remainder of the guarantee on the original product
purchased.
The guarantee does not cover:
- Sinks and taps
- Failure to comply with the manufacturers instructions for use.
- The replacement of cosmetic components of accessories
- Accidental damage or wilful abuse.
- Subsequent loss or damage owing to the failure of the appliance or electrical supply
- Incorrect installation
- Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts
- Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers,
baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals.
In the course of the work carried out it may be necessary to remove the appliance from it operating
position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage
sustained to any property whatsoever in this process.
This guarantee is in addition to and does not diminish your statutory or legal rights.
Contacting Baumatic Ltd
Sales Service Spares Technical/Advice
TEL: 0118 933 6900 TEL: 0118 933 6911 TEL: 0118 933 6922 0118 933 6933
FAX: 0118 931 0035 FAX: 0118 986 9124 FAX: 0118 933 6942 0118 933 6942
For ROI (Republic of Ireland), please contact one of the numbers below:
TEL: 01 – 6266798 FAX: 01 - 6266634
Thanks you for buying Baumatic.
*
Applies to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year labour & 1 year parts warranty only)
29
Page 30
Headquarters
Baumatic Ltd.
Baumatic Buildings,
6 Bennet Road,
Reading,
Berkshire
RG2 0QX, United Kingdom
Sales Telephone
+44 118 933 6900
Sales Fax
+44 118 931 0035
Service Telephone
+44 118 933 6911
Service Fax
+44 118 986 9124
Spares Telephone
+44 118 933 6922
Technical / Advice Telephone
+44 118 933 6933
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Website
http://www.baumatic.com
30
Page 31
31
Page 32
32
32
Loading...