Page 1
CKBM-Z01
BWTE42 electronic
wine cooler
Page 2
User Manual for your
WINE COOLER
NOTE : This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference.
YOUR WINE COOLER'S SPECIFICATIONS ................... 3
SAFETY INFORMATION / ENVIRONMENTAL NOTE .... 4
USING YOUR WINE COOLER .................................. 5-11
YOUR WINE COOLER ................................................... 5
BEFORE USING YOUR WINE COOLER .........................6-7
USING YOUR WINE COOLER ................................... 8-10
CARE AND MAINTENANCE.......................................... 11
TROUBLESHOOTING ......................................... 12-13
CONTACT DETAILS .................................................... 14
CONTENTS
,
1
2
DUAL TEMPERATURE ZONE
LCD DISPLAY
DD 12/02/07
Page 3
Congratulations on purchasing a Baumatic wine cooler
Your wine cooler has:
Gross capacity: 150 litres
4 waved chrome shelves
Two Compartments(upper/bottom): 51/57 litres
1 chrome wine rack
Stainless-steel door frame
Adjustable feet
Dimensions mm (W x D x H)
500 x 590 x 840
To fully enjoy using your appliance long into the future,
please firstly familiarise yourself with the specifications,
safety advice and operational instructions included in this
manual.
NOTE:
When you install your wine cooler, it is important to bear in mind
its climatic rating. In order to find out the climatic rating of your
appliance, check the data rating tag inside of your wine cooler.
It indicates the ambient temperature range in which your
appliance will function properly in. The rating tag can be found on
the left hand side of the of the cabinet. See table on page 7.
Specifications of your wine cooler
Electronic control with LED display
Important Safety Information: Please Read this before installing & using.
Never allow the back coils of the wine cooler
to come into contact with any wall surface.
YOU ARE PLACING YOUR APPLIANCE IN, IS
FREE OF STORED ITEMS SUCH AS PAPER OR
OTHER FLAMMABLE MATERIALS.
NEVER BLOCK THE VENTILATION OPENINGS OF THE
APPLIANCE EITHER INSIDE OR ON ITS EXTERIOR.
IT IS VITAL TO KEEP YOUR WINE COOLER WELL
VENTILATED SO THAT THERE IS PROPER AIR FLOW
BETWEEN THE BOTTOM OF THE UNIT AND THE
PLINTH / KICK PLATE WHICH IT IS SITTING ON.
– WARNING: DO NOT DAMAGE THE REFRIGERANT
CIRCUIT. AT THE END OF THE FUNCTIONAL LIFE
OF THE EQUIPMENT IT MUST BE DISPOSED OF
IN ACCORDANCE WITH THE W.E.E.E DIRECTIVE.
(SEE BELOW). YOUR APPLIANCE CONTAINS R600A
REFRIGERANT AND INFLAMMABLE GAS IN THE
ALWAYS ENSURE THAT THE AREA WHICH
INSULATING FOAM.
ELECTRICAL SAFETY
NOTE - This appliance must be earthed. In the event of a malfunction or breakdown, earthing
will reduce the risk of electric shock by providing the path of least resistance for the electrical
current.
The manufacturer declines all responsibility for any damage due to the non-earthing of the appliance.
BAUMATIC SHOULD CARRY OUT REPAIRS ON THIS UNIT.
DO NOT USE THE APPLIANCE IF THE SUPPLY CORD IS DAMAGED. NEVER TAKE A RISK WITH FIRE!
EN SURE THAT YOU CONNECT THIS APPLIANCE TO A SUPPLY RATED 220-240V (or 200-230V) and 50Hz.
NOTE: the supporting structure of the appliance is constructed in panels of treated stainless steel, which is
electrostatically enamelled to give a long-lasting beauty and shine, providing that it is maintained properly.
Do not attempt to alter the specifications of
this appliance. Doing so could damage the
machine, cause injury & invalidate your warranty.
DO NOT USE AN EXTENSION LEAD.
Do not allow children to play with, near or
inside of this wine cooler.
Do not pull on the power supply cable to remove
the plug from the wall!
Do not attempt to use your wine cooler
outdoors or in any location where it is likely to
come into contact with the elements.
Do not pull out or insert the plug with wet
hands.
Before commencing any cleaning or maintenance
work, ensure that the appliance has been
disconnected from the mains supply.
PLEASE OBSERVE ALL INSTALLATION ADVICE IN THIS MANUAL TO ENSURE
THAT YOU ARE USING YOUR APPLIANCE IN A SAFE MANNER.
Note : Before discarding your wine cooler, switch it off and disconnect it from the power
supply. Cut off and render any plug useless. Ensure that the door cannot shut
completely, regardless of whether or not it can be pushed open from the inside (removing the
door is best). AN OLD WINE COOLER CAN BE A DEADLY PLAYTHING FOR CHILDREN!
CONFORMITY TO W.E.E.E. DIRECTIVE
DURING THE GUARANTEE PERIOD ONLY BAUMATIC SERVICE ENGINEERS OR AN AUTHORISED AGENT OF
3
4
Page 4
5
9. Temperature Sensor
7. Interior Lamp
6. Chrome Shelves
5. Glass Door
4. Wine Rack
3. Levelling Leg
2. Cabinet
1. Operation and Display Panel
8. Electrical Control Assembly (at the back)
6
YOUR WINE COOLER:
Important Safety Instructions
Read all instructions before attempting to use the appliance.
A child could become trapped and suffocate inside of an old and disgarded
wine cooler. Always make sure that the door is disabled and the appliance is
disposed of in a responsible manner.
Never allow children to operate, play with, or crawl inside of the appliance.
Never clean any part of the appliance with flammable fluids. The fumes can
create a fire hazard or explosion.
Do not store or use gasoline or any other flammable vapors and liquids
in the vicinity of
the wine cooler or any other domestic appliance. The fumes
can cause a fire hazard or explosion.
climb inside easily.
Take off the door and leave the shelves in place, so that children cannot
Before you dispose of your old wine cooler, please do the following:
INSTALLATION INSTRUCTIONS
Before Using Your Wine Cooler
Clean the interior surface with lukewarm water using a new soft cloth.
Before connecting the appliance to your mains power supply, you should let it
stand upright for approximately 8 hours. This will reduce the possibility
of the refrigerant not settling properly, if it has been disturbed whilst being
handled during the transportation process.
Remove the exterior and interior packaging, including the protective foam on
the door panels.
Installation of Your Wine Cooler
Place your appliance on a floor that is strong enough to support the
appliance when it is fully loaded. To level your appliance, adjust the
legs at the front of the appliance.
Locate the appliance away from direct sunlight and sources of heat
(E.g. stoves, heaters, radiators, etc.). Direct sunlight may affect the acrylic
coating and heat sources may increase electrical consumption.
Ambient temperatures below the climate classification stated on the rating plate
plate may also cause the appliance not to perform properly.
Allow a space of 5 inches between the back and sides of the appliance, this
will allow proper air circulation and helps to keep the compressor cool.
Using your Baumatic wine cooler Before using your Baumatic wine cooler
1
2
3
4
5
6
7
8
9
c
Page 5
8
7
Before using your Baumatic wine cooler
Do not store food in your wine cooler, as the interior temperature will not be
cool enough to prevent spoilage. The outside of the glass door may suffer
from condensation during the summer or if it is installed in an area of high
humidity. You can simply wipe the condensation away with a cloth.
IMPORTANT SAFEGUARDS
We recommend that you install the wine cooler in a place where the ambient
temperature is between +16 and +32 degrees centigrade. If the ambient
temperature falls outside of this temperature range then it may cause the
interior temperature to fluctuate. The recommended temperatures for
chilling wine are as follows:-
OPERATING YOUR WINE COOLER
Before starting the wine cooler, ensure that the cabinet is level. This will
eliminate the possibility of vibration when the wine cooler is in use.
SETTING THE TEMPERATURE CONTROLS
The wine cooler has two cooling compartments (upper & lower) which are
independently controlled. To set the temperature you should do as follows:-
1. Connect the power cord to a properly grounded outlet. The temperature
preset at factory of each compartment is:
12 C (54 F)-Upper Compartment
6 C (43 F)-Lower Compartment
2. Set the desired cooling temperature by pressing the button or these
are under the Upper Compartment/Lower Compartment text on the control panel.
When you push the buttons for the first time, the LCD readout will show the
previously set temperature. The temperature will increase by 1 degree centigrade
if you push the upward arrow ( ) once. Conversely the temperature will
decrease by 1 degree C by pushing (the downward arrow) once.
If you have altered the display so that it shows in farenheit, the temperature will
increase and decrease in one farenheit steps, rather than one centrigrade steps.
Red wines: 15-18 degrees centigrade
Dry/White Wines 10-15 degrees centigrade
Rose Wines 9-10 degrees centigrade
Sparkling Wines 6-9 degrees centigrade
Beverage 3-6 degrees centigrade
Using your Baumatic wine cooler
Plug the appliance into an exclusive, properly installed and earthed wall
socket. Do not under any circumstances cut or remove the earth wire
from the power cable. Any questions concerning the electrical connection
should be directed towards a certified electrician or the Baumatic Technical
Department.
You must attach the door handle to the left hand side of the frame before
you start to use the wine cooler.
Improper use of the earthed plug can result in the risk of electrical
shock. If the power cable is damaged you should have it replaced by
an authorised Baumatic engineer.
Avoid locating the appliance in a location that gets damp. Too much
moisture in the air will cause frost to form more quickly on the evaporator.
Climate classification Appropriate ambient temperature
SN +10 to +32 degrees centigrade
N +16 to +32 degrees centigrade
ST +18 to +38 degrees centigrade
T +18 to +43 degrees centigrade
Page 6
9
Upper Compartment: The temperature setting can be adjusted between
10 C - 18 C (50 F - 64.4 F) ;
Lower Compartment: The temperature setting can be adjusted between
3 C - 10 C (37.4 F - 50 F).
The temperature of the bottles may fluctuate, depending on whether they
are located in the upper/middle or lower section.
3. To view the set temperature at anytime, press the corresponding
or button, the set temperature will temporarily flash in the LCD
display for 5 seconds.
Flashing LCD = Set Temperature
Steady LCD = Cabinet Temperature
4. This unit has the option to display the temperature in either Celsius or
Fahrenheit. To change this setting, press the button marked C/F.
5. You can turn the interior lights on or off by pressing the button with a light
bulb on it. The interior lights are LED lights and low energy bulbs
(only 0.25W for each one) and low heat. However they should not be left on for long
periods of time, only whilst you are looking inside of the wine cooler.
6. Your wine cooler is designed with an Auto-Cycle defrost system. During
the Off-Cycle the refrigerated surface of the wine cooler (interior rear wall)
will defrost automatically. The defrost water is channelled into a drain pan
which is located at the back of the wine cooler on the top of the compressor,
from where it will evaporate.
Shelves
The shelving is chromed, so they can accommodate different sized bottles, they
can be moved up or down by sliding them out of their grooves. The original shelf
positions are designed to accommodate the maximum number of bottles.
Wine Rack
There is an additional wine rack at bottom section of the unit where you
can store up to 6 wine bottles. This rack is removable for cleaning purposes.
Using your Baumatic wine cooler
NOTE:
When you use the wine cooler for the first time or restart the wine cooler
after it has been turned off for a long time. There could be a few degrees
variance between the temperature that you have selected and the temperature
that the LCD shows that the inside of the cabinet is running at. This is normal
and the wine cooler will take a few hours to get down to temperature. Once
this happens, operation will return back to normal.
There is also a 2 to 3 C variance between the upper and lower shelves of
each wine compartment. Therefore, if you have set the wine cellar for red wine
only and the temperature reads 16 C and you want to place a mixture of white
and red wines in the appliance, you should place the white wine bottles on the
lower shelves and the red wine bottles on the upper shelves.
Using your Baumatic wine cooler
10
Page 7
CHANGING THE LIGHT BULBS
Note: All parts removed during this process must be saved and refitted
after the bulb has been replaced. Before removing the LED light, unplug
the wine cooler from your mains supply.
Failure to do so could result in electrical shock or personal injury.
You should use an LED bulb which is of the same type as the bulb
originally supplied with the appliance.
Make sure that the wine cooler remains in the upright position during
transportation.
Tape the doors shut.
Turn the levelling feet fully up to the base to avoid damage.
Securely tape down all loose items inside of your wine cooler.
Remove all of the bottles.
Moving Your Wine Cooler
During long absences, remove all of the bottles; unplug your wine cooler,
clean it, and leave the door open slightly to avoid the possible formation
of condensation or mould.
Vacation Time
Most power failures are corrected within a few hours and should not
affect the temperature of your wine cooler, as long as you minimize the
number of times that the door is opened. If the power is going to be off
for a longer period of time, you should take steps to protect the contents
of your wine cooler.
Power Failure
Maintenance of Your Wine Cooler
Unplug the wine cooler, and remove all bottles.
Wash the inside with a mixture of warm water and baking soda.
The solution should be approximately 2 tablespoons of baking soda to
one quart of water.
Wooden shelves do not require cleaning.
The outside of the wine cooler should be cleaned with a mild detergent
and warm water.
It may also be necessary to periodically wipe the bottom part of the
storage area, as the wine cooler is designed to retain humidity, and
condensation may collect there.
Cleaning Your Wine Cooler
CARE AND MAINTENANCE
11 12
The light bulbs have been switched off with the
The LED light has burnt out(see maintenance section
for the replacement procedure).
The wine cooler is unplugged.
The home circuit breaker or fuse has tripped.
The wine cooler does not have the correct ventilation
The door gasket does not seal properly.
The temperature control is not set correctly.
The door is not closed completely.
The door has been opened too often.
A large amount of warm wine has been added to the
wine cooler.
The room temperature is hotter than normal.
The wine cooler does not have the correct ventilation
The door gasket does not seal properly.
The door is not closed completely.
The door has been opened too often.
The e
xternal environment may require a lower setting.
Wine cooler is
not cold enough.
The circuit breaker has tripped or a fuse has
Wine cooler does
not operate.
PROBLEM
TROUBLESHOOTING GUIDE
You can solve many common wine cooler problems easily, saving
yourself the cost of a possible service call. Try the hints below to
see if you can solve the problem before calling the Baumatic Service
Troubleshooting
POSSIBLE CAUSE
Not plugged in.
T
he temperature control is not set correctly.
Compressor turns
on and off frequently
The light does
not work.
Troubleshooting
Department.
blown.
clearances to the rear or side of the wine cooler.
clearances to the rear or side of the wine cooler.
light bulb ON/OFF switch.
Page 8
14
13
The shelves are not positioned correctly.
Technical Specifications:
For detailed specifications, please refer to the rating plate at the back
of the wine cooler. The specifications are subject to change without
prior notice due to a policy of continuous product improvement.
The door gasket is dirty.
The doors were reversed and not properly installed.
The wine cooler is not level.
The wine cooler is not level.
Contraction and expansion of the inside walls may
cause popping and cracking noises.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in your wine cooler.
The rattling noise may come from the flow of the
refrigerant,which is normal.
Check to make sure the wine cooler is level
Vibration
The wine cooler
seems to make
too much noise.
The door will not
close properly.
Troubleshooting
Baumatic Ltd
Make-up for your kitchen
Headquarters
Baumatic Ltd.
Baumatic Buildings,
6 Bennet Road,
Reading,
Berkshire
RG2 0QX, United Kingdom
Sales Telephone
+44 118 933 6900
Sales Fax
+44 118 931 0035
Serv ice Telephone
+44 118 933 6911
Service Fax
+44 118 986 9124
Spares Telephone
+44 118 933 6922
Technical / Advice Telephone
+44 118 933 6933
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Http (Internet site):
www.baumatic.com
Baumatic UK/cod. 1230000666
Page 9
NOTE YOUR APPLIANCE DETAILS HERE:
DATE _______
DEALER:
ADDRESS:
SERIAL NUMBER:
15
Loading...