Page 1
BWR1005/BWR1206
Fully integrated
washing machine
Page 2
USER MANUAL FOR YOUR BAUMATIC
BWR1005/BWR1206
Fully integrated washing
machine
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference.
DD 10/05/11
2
Page 3
Contents
Environmental note 4
Important safety information 5 - 6
Specifications 7 – 11
Product and aperture dimensions 7
Product specifications 7 - 8
Description of the appliance 8
Control panel 9 - 10
Detergent drawer 11
Preparing the wash cycle 12 - 16
Preparing your garments for washing 12
A selection of wash care symbols 13
Detergents and conditioners 13 - 14
Program table 15 - 16
Wash program guidance 16
Selecting a wash program 16 – 21
At the end of a wash cycle 17
Pausing a wash program 18
Cancelling a wash program 18
Spin selection button 19
Temperature selection button 19
Soak option button 19
Extra rinse option button 20
Delay start button 20
Child lock 21
Maintenance and cleaning 22 - 23
In daily use 22
Control panel and washing machine cabinet 22
Detergent drawer 22- 23
The washing machine drum 23
Door 23
Error code failure system 24 - 31
General troubleshooting 26
Poor wash results 27
Removing stains 28
Stain removal rules 28
Stain removal guide 28 - 29
Cleaning the drain pump filter 30 - 31
Installation 31 - 39
Unpacking and removing the transit bolts 31 - 32
Positioning and levelling the appliance 33 - 34
Fitting the décor strip 34
Connecting to the mains water supply 34 - 36
Water outlet 36
Fitting the furniture door 37
Power supply 38
Before first use maintenance wash 39
Contact details 40
3
Page 4
Environmental note
Note
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
: Before discarding an old appliance, switch off and
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
Page 5
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Safety
o Repairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorised service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your washing machine.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
o The appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The glass of the porthole door may become hot during the higher
temperature wash programs.
o The machine should be allowed to cool before carrying out an
emergency drain or cleaning the drain filter.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard.
Installation
o The installation instructions contained within this user manual
should be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
5
Page 6
o Before the first use of the appliance, we advise that the
intense 90°C wash program is completed. No garments
should be placed inside the machine; however a small
amount of detergent must be used.
During Use
o It is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
o This appliance is only designed to wash normal domestic
washloads. If you use your washing machine in any other way or
it is incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
o No attempt should be made to alter or modify the specifications
of this appliance.
o The detergents that you place in this appliance should be
suitable for automatic washing machines. With regards to dosage
levels, the detergent manufacturer’s recommendations should be
followed.
o You should not wash garments that have been in contact with
flammable materials.
o Your washing machine should not be used for dry cleaning.
o If you use either dyes or bleaching agents inside this machine,
then you should consult with the manufacturer of these products
to make sure they are suitable for use in your washing machine.
Baumatic cannot be held responsible for any damage that may
result.
Child Safety
o Your washing machine should only be used by adults. You should
not allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
washing machine through the porthole door. Therefore please
check the drum before using the appliance.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
6
Page 7
Specifications
Product and aperture dimensions
Appliance dimensions Aperture dimensions
Height: 825 mm 830-860 mm
(excluding décor strip)
Width : 595 mm 600 mm
Depth: 565 mm 580 mm
Product specifications
o 15 wash programs
o 6 kg wash load
o 1000 rpm maximum spin speed (BWR1005)
o 1200 rpm maximum spin speed (BWR1206)
o LCD display
o Delay start timer with remain time indicator
o 2 Option buttons: Extra rinse
Soak
o Spin and temperature selection buttons
o Door safety lock
o Child lock
o Stainless steel drum
o Adjustable feet
o Error code failure system
o Overflow protection
7
Page 8
o Imbalance control system
o Tilted drum
Energy efficiency (BWR1005) (BWR1206)
Energy rating A A
Wash performance A A
Water extraction performance B B
Electrical details
Rated voltage: 220 - 240 Vac 50 Hz
Supply connection: 13 A (double pole switched fused outlet with
3 mm contact gap)
Description of the appliance
8
Page 9
Control panel
A Wash program selection knob
B Start/pause button
C Temperature selection button
D Spin selection button
E Delay start button
F Soak option button
G Extra rinse option button
H Detergent drawer
I LCD display
J Timer indicator neons
K Spin speed indicator neons
L Wash temperature indicator neons
M Start/pause indicator neon
Wash program selection knob
o Turning the control knob anti-clockwise or clockwise allows you
to select the wash program of your choice.
Start/pause button
o Once a wash program has been selected, this button should be
pressed to start the wash cycle. Or to pause a wash cycle that is
in progress.
Temperature selection button
o Press this button to select the temperature that you require for a
particular wash program.
9
Page 10
Spin selection button
o Press this button to select the spin speed that you require for a
particular wash program.
Delay start button
o Press this button to delay the start of the wash program for a
maximum of 24 hours.
Soak option button
o Press this button to select the “soak” wash program option.
o When the wash cycle reaches the final rinse, instead of draining
the water, it will suspend the clothing in water. This option
allows you to spin the wash load at a later time.
Extra rinse option button
o Press this button to select the “extra rinse” wash program
option.
o The appliance will then perform an additional rinse.
LCD display
o The LCD display will show how much time a wash cycle has until
it completes.
o If the delay start button has been pressed, then the LCD display
will show the remaining time until the wash cycle will commence.
10
Page 11
Detergent drawer
1) Pre wash section
This compartment should have detergent placed in, if you are going to
select a wash program that has a pre wash as part of it.
2) Main wash section
This compartment should have detergent placed in it (you should also
put a water softening agent in this section, if you use one). The
detergent will be added to the drum at the start of the main wash
program.
3) Conditioner section
This compartment should be used for liquid conditioners (fabric
softener, starch). They will be added to the wash load during the final
rinse.
IMPORTANT: Liquid detergent should not be placed in sections
1 or 2 of the detergent drawer.
11
Page 12
Preparing the wash cycle
Preparing your garments for washing
o Your washing should be sorted out, according to
the fabric type and the wash care symbol that is
printed on the garment’s wash care label. (see
separate section on wash care symbols).
o Your washing should also be sorted out
according to the degree of soiling.
o Check all pockets on a garment to make sure
that they are empty.
o Remove any detachable metal items (badges,
paperclips, safety pins etc).
o Zips should be closed, duvet covers and pillow cases should be
buttoned up and any loose straps should be tied up. This will
help to prevent other garments from getting damaged during the
wash.
o Woollens and knitted coloured fabrics should be turned inside out
before being washed in the appliance.
o Small delicate items (tights, baby socks) should be placed in
either a washing net or a zipped pillow case.
o Curtains should be handled with particular care. All plastic hooks
or metal strips must be removed before being washed in the
appliance.
o Coloured items and whites should be washed
in separate wash cycles.
o New garments often contain an excess of
dye, therefore it is advisable to wash them separately for their
first wash.
o Garments should be unfolded and shook out before being placed
inside the machine.
12
Page 13
A selection of wash care symbols
Washing
Dry
cleaning
Spin
dryer
Ironing
Boiling
temp
95°C
Delicate
temp
30°C
Normal
110°C
Normal
Delicate
temp
60°C
temp
40°C
Low
150°C
Normal
temp
40°C
Hand
wash
High
200°C
only
solvents
Do not
wash!
All
Do not
dry!
Do not
iron!
Bleachable
in cold
All but TRI
Hang to
water
dry
Do not
bleach!
Benzine
only
Drip dry
o The wash care symbols should be used to help you to select the
most suitable wash program. They will also help you to sort your
laundry into different loads, depending on the fabric type and the
highest temperature which the garment can be washed at.
o If the wash care label does not appear in the above table, then
please refer to the washing machine program chart. This gives
more detailed descriptions of the types of fabric that are suitable
to be washed using a particular wash program.
Wool
seal
Do not
clean!
Dry
flat
Detergents and conditioners
The amount of detergent that you need to use in your appliance, will
depend on
o The degree of soiling. Lightly soiled garments in general
require less detergent.
o The size of the wash load. A smaller wash load will require a
reduction in the amount of detergent.
o The hardness of your tap water. The harder your water is,
then the more detergent you will need to use. The detergent
manufacturers normally give guidance as to how much extra
detergent should be used, depending on the hardness of the
water.
13
Page 14
Liquid detergent
o If you are using liquid detergent, then it should be placed inside
the dosing device supplied by the detergent manufacturer.
o IMPORTANT: Liquid detergent should not be placed in
sections 1 or 2 of the detergent drawer.
o All instructions on the detergent packaging should be followed.
Water softening agents
If your tap water is hard, then it may be prudent to utilise a water
softening agent. This will help to ensure that the appliance does not
become clogged with hard water deposits. You may also find that it will
allow you to lessen the amount of detergent that you are using.
When using any detergent or water softening
agent, the recommendations of the
manufacturer should be followed.
14
Page 15
15
15
Page 16
- Indicates that softener can be added if required.
- Indicates that detergent MUST be added.
- Indicates that detergent MUST not be added.
Wash program guidance
o The default setting column shows the wash temperature and spin
speed that the appliance will automatically select for a particular
wash program. It is possible to override these settings, using the
spin selection button and temperature selection button.
o IMPORTANT: You should make sure that the spin speed and
temperature that you select are appropriate for the garments
that you are washing.
o The wash cycle times that are quoted and shown by the LCD
display, are intended as a guide only. Please note that factors
external to the machine, e.g. the temperature of your water
supply, your water pressure etc. can affect the time it takes for
the wash cycle to complete.
o If you select the soak option, the machine will not spin the
clothing at the end of a wash cycle. If you pick this option, then
the machine will stop with water inside of the drum.
o Important: Before opening the door of the appliance, you MUST
select the drain program to clear this water.
Selecting a wash program
9 Load your laundry and put detergent in the relevant
compartment(s) of the soap drawer.
9 Close the porthole door firmly.
9 Select the most appropriate wash program for the garments that
you are washing, by turning the program selector knob.
o The washing machine will automatically select a spin speed and
wash temperature for the wash program that you have chosen.
o The spin speed indicator neon will light to confirm the spin speed
that has been chosen. The wash temperature indicator neon will
light to confirm the wash temperature that has been chosen.
16
Page 17
9 If you press the spin selection button, then you can adjust the
spin speed. The spin speed indicator neon will light next to the
spin speed that you have chosen.
9 If you press the temperature selection button, then you can
adjust the wash temperature. The wash temperature indicator
neon will light next to the wash temperature that you have
chosen.
9 Select any program options that you require (soak, extra rinse,
delay start) by using the relevant buttons. For more information,
please refer to pages 19 - 20.
o Any program option that you select, will affect the length of time
that the wash cycle will take to complete.
9 Press the Start/pause button.
o After approximately 5 seconds, you will hear your washing
machine start the wash cycle.
o Throughout the wash cycle, the LCD display will countdown the
remaining time of the wash cycle that is in progress.
If there is a power failure or the plug is pulled out of the socket
when a wash cycle is in progress. Once power has been
restored, the wash program will continue.
At the end of a wash cycle
o The washing machine will stop automatically when it has
completed a wash cycle.
o The LCD display will show the word “End”.
o At the end of the drain program, the door will remain locked for
2 – 3 minutes before it is possible to open the door and take out
the garments.
o If the spin speed indicator neon next to the
at the end of the wash program, the washing machine will not
have spun the wash load.
symbol is lit, then
17
Page 18
Pausing a wash program
9 Press the Start/pause button whilst a wash cycle is in progress
and the appliance will go into pause status.
o In pause status, the Start/pause indicator neon will flash.
9 Press the Start/pause button again and the wash cycle will
continue.
Cancelling a wash program
9 Press the Start/pause button whilst a wash program is in
progress and the appliance will go into pause status.
o Turn the wash program selection knob until it is at the off
position (zero).
Before opening the porthole door, you MUST drain the
appliance; otherwise there may still be water in the
drum when you open the door.
9 Turn the wash program selection knob to the drain program
(number 15) then press the Start/pause button.
o The appliance will then drain the water that is left in the drum.
o The washing machine will stop automatically when it has
completed a wash cycle.
o The LCD display will show the word “End”.
o At the end of the drain program, the door will remain locked for
2 – 3 minutes before it is possible to open the door and take out
the garments.
18
Page 19
Spin selection button
o If you press the spin selection button, then the spin speed will
reduce downwards from the one selected automatically for a
particular wash program.
o The spin speed indicator neon will light next to the spin speed
that has been selected.
o If the spin speed indicator neon next to the symbol is lit, then
at the end of the wash program, the washing machine will not
spin the wash load.
Temperature selection button
o If you press the temperature selection button, then the wash
temperature will reduce downwards from the one selected
automatically for a particular wash program.
o The wash temperature indicator neon will light next to the wash
temperature that has been selected.
o If the wash temperature indicator neon next to the symbol is
lit, then the wash cycle will be performed in cold water and not
heated.
Soak option button
o If you press the soak option button, the indicator neon above it
will light.
o When the wash cycle reaches the final rinse, instead of draining
the water away, it will suspend the wash load in water.
o When you want to spin the wash load, press the soak option
button again. The indicator neon will go out and the spin stage of
the wash cycle will take place.
o IMPORTANT: This option can be utilised on synthetic and
delicate wash programs (programs 5 – 11).
19
Page 20
Extra rinse option button
o If you press the extra rinse option button, the indicator neon
above it will light.
o If you select this option, an additional rinse will be performed for
the selected wash program.
o IMPORTANT: This option can be utilised on cotton, synthetic,
wool, cashmere and silk wash programs (programs 1 – 10).
Delay start button
o If you press the delay start button, then you can program the
wash cycle to commence at a period of time in the future.
o You should select your wash program as normal, but instead of
pressing the Start/pause button to get the wash cycle to
commence. You should press the delay start button.
o Each time the delay start button is pressed, the length of time
until the wash cycle commences will increase by 30 minutes. The
minimum delay start is 2 hours 30 minutes.
o It is possible to delay the start of the wash cycle by a maximum
of 24 hours.
o Press the Start/pause button and the countdown time will
commence. The delay time indicator neon will light and the LCD
display will countdown the remaining time until the wash cycle
commences.
o Once the delay start time has been reached, the wash program
that you have previously selected will start. The remaining time
indicator neon will light and the LCD display will countdown the
remaining time of the wash cycle that is in progress.
20
Page 21
Child lock
o Your appliance has a child lock option, if this is set, it will mean
that nobody can affect the operation of the wash program once it
has started.
o The child lock should be activated, once a wash program and any
program options that you wish to use have been selected.
o Press the Start/pause button to commence the wash cycle. Then
press the soak option button and the delay start button
simultaneously.
o The word “LOCt” will appear on the LCD display, alternating with
the remaining program time.
o When the child lock is engaged, all other buttons on the control
panel are disabled.
o To switch the child lock off, you should again press the soak
option button and the delay start button simultaneously.
21
Page 22
Maintenance and cleaning
In daily use
9 Once a wash cycle has completed, you should pull out the
detergent drawer slightly, so it can dry out.
9 Leave the porthole door ajar for a short while after a wash
cycle has completed. This should help to prevent stagnant
smells and to protect the door seal.
9 Close the water tap.
9 We suggest that you disconnect the appliance from your
mains supply, when it is not in use.
Control panel and washing machine cabinet.
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
9 Wipe over the control panel and the external surface of the
machine using a brand new damp cloth with warm water.
9 If you ever spill any liquid detergent or conditioner from the
detergent drawer onto the washing machine cabinet, then
these should be cleaned up immediately as they could be
corrosive.
Detergent drawer
Occasionally the detergent drawer should be cleaned.
o Swing open the detergent drawer and
then remove the drawer by pulling it
forward.
22
Page 23
o Use warm water and a brush to thoroughly
clean the three compartments of the
detergen
o Clean the area that the detergent drawer
slides into with a brush.
o Replace the detergent drawer by placing it back into the slot.
Then slide the drawer fully back into position.
The washing machine drum
t drawer.
The drum of your washing machine is constructed from stainless steel.
However if there are objects that can rust placed inside the drum, then
it is possible for the drum to become stained.
IMPORTANT: Do not use a descaling agent, iron/steel wool or
scouring agents to clean the drum of your appliance.
9 Remove any rust stains on the drum with an appropriate
stainless steel cleaning agent.
Door
9 You should regularly check to see if any deposits have
formed, or there are any foreign bodies in the rubber door
gasket. This sits inside the opening of the porthole door.
23
Page 24
Error code failure system
If your appliance senses that it is not operating correctly, then an error
code may appear in the LCD display.
Some of the error codes can possibly be remedied by the customer
and the steps outlined below should be followed.
BEFORE COMPLETING ANY MAINTAINEANCE ON THE
APPLIANCE, IT SHOULD BE DISCONNECTED FROM YOUR MAINS
POWER SUPPLY.
Err1
o Door is not shut properly
9 You should regularly check to see if any deposits have formed, or
there are any foreign bodies in the rubber door gasket. This sits
inside the opening of the porthole door.
Err2
o Drainage error, water has not emptied within 4 minutes.
9 Clean the drain pump filter and check that the outlet hose is not
blocked or kinked.
Err3
o Temperature sensor short circuit or open circuit.
9 Contact the Baumatic Customer Care Department.
Err4
o Machine does not fill to the specified level within 8 minutes.
9 Check that the inlet hose is not kinked or blocked and that the
water tap the machine is connected to is fully open.
Err5
o Machine has filled to an abnormal level.
9 Contact the Baumatic Customer Care Department.
Err7
o Motor error
9 Contact the Baumatic Customer Care Department.
24
Page 25
If a fault code reappears after following the
advice given on the preceding page, you
should turn the wash program selection knob
to the off position. Disconnect the appliance
from your mains supply. Then arrange for an
engineer to attend the appliance. You should
contact the Baumatic Customer Care
Department on (0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
IMPORTANT: Baumatic Ltd. operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.
25
Page 26
General troubleshooting
Water under the washing machine
o Tighten the drain pump filter.
o Check the drain and inlet hose and make sure that they are fully
tightened.
Washing machine vibrates during the spin cycle
o Check that the transit bolts have been removed (see installation
instructions).
o Make sure that the washing machine is installed on a flat and level
floor.
o Ensure that all four feet are resting firmly on the floor, by pressing
down on each corner and making sure that the appliance is stable.
o If it is unstable then follow the “Positioning and levelling the
appliance” section.
Poor spin results
o Clean the drain pump (see “Cleaning the drain pump filter” section).
Water in the detergent dispenser
o Although there will be some water residue left in the detergent
drawer after a wash cycle has completed. If the drawer is full of
water then you may need to clean the detergent drawer.
Spinning starts late or the machine does not spin
o The imbalance control system has activated because the laundry
is unevenly distributed in the drum.
o The appliance will redistribute the laundry by reversing the drum
rotation. This may take several attempts before the laundry is
evenly distributed and normal spinning can resume.
o If the laundry is still not evenly distributed after 10 minutes, the
machine will not spin. In the event of this, redistribute the load
manually and select the program again.
Uneven load distribution can be caused by too large a wash
load or too small a wash load. It can also occur if a single item
if washed inside the appliance.
26
Page 27
Poor wash results
My garments are looking grey and there are limescale
deposits present in the drum of my washing machine.
o There is not enough detergent being added.
o The incorrect detergent is being used.
o Stains are not being pre-treated.
o The correct wash program or wash temperature was not
selected.
I have followed the advice given above, but my
garments are still coming out with grey stains on them.
o The garments are soiled with oils, ointments or grease
and were washed without enough detergent.
o The wash temperature selected was too low.
o Fabric conditioner has come into contact with the
garments. If this happens try to wash out these stains
as quickly as you can and try to avoid getting
conditioner on the garments in future.
After the final rinse, I can still see foam.
o Modern detergents can result in there still being foam in the final
rinse, this does not mean that the washing is not being rinsed
properly.
There is white residue on my garments when I remove
them from the appliance.
o Modern detergents can contain insoluble contents, and white
residue after a wash cycle is not necessarily a sign of the garments
not being rinsed properly.
o You should shake out the garment or brush it off. In future possibly
turn the garment inside out before it is washed. You may wish to
move from a powder detergent and switch to a liquid detergent
instead.
27
Page 28
Removing stains
Garments that are covered in stains, grease or are heavily soiled may
need to be pre-washed or soaked before being placed inside of the
washer dryer.
o Soaking helps to remove protein-type stains, like blood, milk or
grass.
o Pre-washing helps to loosen soil before the main wash.
Stain removal rules
o Use warm water for soaking or pre-washing stained laundry. Hot
water can set stains.
o Most stains are easier to remove when they are fresh.
o Before treating any stain try to establish; what kind of stain it is,
how old the stain is, what the fabric type is and whether the
fabric is colourfast (check the care label to find this out).
o Washing and drying can fix some stains.
o When bleach is recommended, use a mild fabric bleach that is
safe for the fabric.
o If you need to use a stain remover, put the stained area face
down on a paper towel or white cloth. Apply the stain remover to
the back of the stain. This forces the stain off the fabric, instead
of through it.
Stain removal guide
Stain Removal Method
Alcoholic
beverages
Shoe polish The stain should be softly scratched without ruining the
Tea and
coffee
Chocolate
and cocoa
The stain should be first washed with cold water, then
wiped with glycerine and water and rinsed with water
mixed with vinegar.
material, then rubbed with detergent and rinsed. In case
it is not eliminated, rub with 1 unit of pure alcohol (96
degrees) mixed in 2 units of water and then washed with
lukewarm water.
Stretch the stained area of material on the top of a
container and pour water as hot as the material can
endure on it. If the type of material is suitable, wash it
with lye.
Leave your clothes in cold water and rub with soap or
detergent, wash it in the highest temperature that the
material type can endure. If there is still a stai n of oil left,
wipe with oxygenated water (in proportion of 3%).
28
Page 29
Tomato
paste
Meat broth/
egg
Grease and
oil stains
Mustard First apply glycerine to the stained area. Rub with
Blood stain Lay your clothes in cold water for 30 minutes. If the stain
Cream, ice-
cream and
milk
Mould Mould stains should be cleaned as soon as possible. The
Ink Hold th e stained area under cold water an d wait until the
Fruit Stretch the stained area of your clothes on the top part of
Grass stain Rub the stained part with detergent. If the type of fabric
Oil paint Th e stain should be eliminated before it dries by applying
Burnt stain If your fabric is suitable for the use of lye, you can add
Scrape the dried pieces without ruining the material, then
leave in cold water for about 30 minutes and wash by
rubbing with detergent.
Eliminate the dried stain residues and wipe with a sponge
or soft cloth wetted in cold water. Rub with detergent and
wash with diluted lye.
First wipe the residues. Rub the stain with detergent and
then wash with lukewarm soapy water.
detergent and then wash. If the stain still does not
disappear, wipe with alcohol (on synthetic and coloured
cloth, a mixture of 1 unit alcohol, 2 units water should be
used).
still does not disappear, lay in mixture of water and
ammonia (3 table-spoons of ammonia in 4 litres of water)
for 30 minutes.
Lay your clothes in cold water and rub the stained area
with detergent. If the stain has still not disappeared,
apply lye on the fabric of your clothes in proper
proportion. (Do not use lye on coloured clothes).
stain should be washed with detergent, and if it does not
disappear, it should be wiped with oxygenated water (in
proportion of 3%).
inky water completely runs off. Then rub with water
diluted with lemon juice and detergent. Wait five minutes
and then wash.
a container and pour cold water on it. Do not pour hot
water on the stain. Wipe with cold water and apply
glycerine. Wait for 1-2 hours and rinse after wiping with a
few drops of white vinegar.
is suitable for use of lye, wash it with lye. Rub your
woollen clothes with alcohol (for coloured one, a mixture
of 1 unit pure alcohol and 2 units of water).
thinner on it. Then it should be rubbed with detergent and
washed.
lye into your washing water. For woollen fab rics, a cloth
dampened in oxygenated water should be pressed on the
stain and it should be ironed with a dry cloth on it. It
should be washed after rinsing well.
29
Page 30
Cleaning the drain pump filter
IMPORTANT: Switch off your washing machine and
disconnect the plug from your mains supply.
You should clean out the filter approximately every twenty
washes. If the drain pump filter is not cleaned regularly, then
your appliance may find it difficult to pump out water
efficiently.
o Locate the drain pump filter in the
bottom right hand corner of the
appliance.
o Place a container under the drain
pump filter, to collect any excess
water that may come out of the drain
pump when it is removed.
o Turn the filter a quarter turn anti clockwise, water
will start to come out of the drain pump. Continue
to turn the filter anti clockwise until you reach a
half turn, more water will come out of the drain
pump.
o When all the water has drained out of
the washing machine, turn the filter
several times anti clockwise, until it
can be removed complete
ly.
30
Page 31
o Remove the filter and
rinse out the filter under
the ta
p.
o Remove any debris from
the filter.
o Remove any debris that is in the area of the appliance that you
removed the drain pump filter from.
o Screw the filter clockwise back into position, making sure that it
is fully tightened. You should keep turning until you cannot turn
it any further.
o IMPORTANT: Do not perform this operation if the
appliance has stuck on a cycle, until the water inside of
the machine has cooled sufficiently. Otherwise the water
that comes out of the drain pump filter may still be hot.
Installation
IMPORTANT: THIS INSTALLATION MUST BE
COMPLETED BY A SUITABLY QUALIFIED PERSON.
BAUMATIC ONLY SANCTION THE INSTALLATION
GIVEN IN THIS INSTRUCTION MANUAL. YOU
SHOULD KEEP THE TRANSIT PACKAGING, IN CASE
YOU NEED TO TRANSPORT THE MACHINE IN THE
FUTURE.
Unpacking the machine and removing the transit bolts
IMPORTANT: The transit bolts MUST be removed before your
washing machine is used for the first time.
o Remove the back plate
from the rear of the
appliance.
31
Page 32
o The location of the three
transit bolts are shown in the
diagram opposite.
o You should use a spanner to
loosen and remove the top
transit bolt first.
o There is also a transit bar
across the top of the
appliance which should be
removed.
o Use a spanner to loosen and remove the two remaining transit
bolts.
o You should also remove the rubber
grommets from the holes; these are
exposed once the transit bolts are removed.
o Replace the back plate on the rear of the appliance.
o Insert the plastic
caps that are
supplied, into the
holes that you
have removed the
transit bolts from.
32
Page 33
Positioning and levelling the appliance
9 Place the washing machine on a solid and level floor surface.
9 DO NOT PLACE THE WASHING MACHINE ON A CARPET.
9 Loosen the adjustable feet
that are positioned on the
base of the appliance.
9 Slacken off the lock nut on each of the washing
machine feet using a spanner.
9 Adjust the feet to level off the washing
machine.
9 Once levelle
lock nut ba
machine feet using a spanner.
IMPORTANT: Wh en the washing machine is positioned in the location
where it will be used. Make sure that all four feet are resting firmly on
the floor, by pressing down on each corner and checking that the
appliance stands still.
d correctly, you should tighten the
ck up on each of the washing
33
Page 34
o If you are fitting the optional décor strip (see below). You should
take into account the height that this will add to the appliance,
when adjusting the levelling feet.
Fitting the décor strip
o Your appliance is supplied with an optional décor strip that can
be fitted to the top of the appliance.
9 You should screw the décor strip to the front edge of the
appliance, using the screws provided.
Connecting to the mains water supply
o Your appliance is a hot and cold fill
machine. Ideally you should
connect an inlet hose to the hot
water inlet valve and the cold
water inlet valve.
o If you only have a cold water supply available, you should connect
the two hoses to the cold water outlet, by using a “Y” connection
piece.
o Alternatively, there is a blanking cap supplied with the appliance,
you can securely tighten this over the hot water valve. The washing
machine will adjust to allow the correct amount of water through
the cold inlet hose.
o The water inlet hoses will be
inside the drum of your washing
machine, when you receive the
appliance.
34
Page 35
o When you are facing the rear of the appliance, you will see two
water inlet valves next to each other. The cold water inlet valve
is on the left hand side and the hot water inlet valve is on the
right hand side.
9 Place the water inlet hose on the water inlet valve at the rear of the
washing machine.
9 Connect and fully tighten the inlet hoses to the threaded inlet valve
that is located at the rear of the washing machine. On the end of
the water inlet hoses there are connectors that have a nut on it,
you should use these to secure the hoses.
9 Connect the other end of the inlet hoses to your mains
water supply
o IMPORTANT: If you are using both inlet hoses, then
you must ensure that you connect the inlet hoses to
the correct taps. The cold water inlet valve must be
connected to your cold water tap. The hot water inlet
valve must be connected to your hot water tap.
35
Page 36
9 IMPORTANT: There should be a filter sitting inside the end of the
inlet hoses that connects to your mains water supply. The inlet
hoses may leak if this filter is missing. This filter is supplied with the
appliance, you should contact Baumatic to obtain one, if it is
missing.
9 Tighten the inlet hoses to your mains supply fully, but do not over
tighten as this may distort the filter that sits in the end of the inlet
hoses.
9 Test for any leaks.
Water outlet
9 Secure the drain hose, so that it cannot move whilst the washing
machine is in use.
9 Place the end of the drain hose on your drain pipe. Push it a
short way down into your drain pipe.
9 IMPORTANT: Do not insert the drain hose too deeply into the
water pipe, as this may cause siphoning.
9 NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
36
Page 37
Fitting the furniture door
o Please refer to the building in template for instructions on how to
fit your integrated appliance and connect the furniture door to
the product.
o Mount the furniture door to the cabinet of the washing machine,
using the hinges supplied.
o Fix the magnet assembly to the front of the washing machine
and the furniture door.
37
Page 38
Power supply
9 IMPORTANT: As your appliance is a built in product, the
electrical socket must still be accessible once the
appliance is installed.
9 Consult the rating plate, located on the back of the appliance
BEFORE making the electrical connections. Ensure that the
voltage reaching the plug, is the same as that on the rating
plate.
9 DO NOT REMOVE THE RATING PLATE AS THE
INFORMATION ON IT IS IMPORTANT.
9 The moulded plug that is supplied with the appliance must be
placed into an earthed and insulated socket.
9 Broken or damaged power leads must only be replaced by a
suitably qualified person. A power lead of a similar type must be
used in replacement.
9 Power lead type – H 0 V V – F 3G 1,5.
9 IMPORTANT: We do not recommend that this appliance is
connected to an extension lead.
38
Page 39
Before first use maintenance wash
o When your washing machine has been correctly installed, we
recommend that you perform a maintenance wash cycle.
o This will check that all aspects of the installation are correct; it will
also remove any deposits that may have been left on the drum by
the manufacturing process.
o Select the intense 90°C wash program.
o A small quantity of detergent should be used during this
maintenance wash.
39
Page 40
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Republic of Ireland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
Czech Republic
Baumatic CR s.r.o.
Lípová 665
460 01 Liberec 4
Czech Republic
+420 483 577 200
www.baumatic.cz
Slovakia
Baumatic Slovakia, s.r.o.
Galvániho 7/D
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Lilienthalstrasse 1
320 52 Herford
Deutschland
+49 5221 694 99-0
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
Nederland
+3136 549 1555
www.baumatic.nl
40
Page 41
41
Page 42
42
Page 43
43
Page 44
44
Loading...